Question about 1999 Mercedes-Benz S-Class

1 Answer

WHERE IS THE BRAKE SENSOR LOCATED ON THAT CAR M.B.S320 1998

I THINK MY CAR SENSOR IS BAD BECAUSE I CHANGED THE ANT-LOCK BRAKE PUMP AND THE LIGHT STILL COMES ON.PLUS THE BRAKE PADDLES GOES TO THE FLOOR OFF AND ON WHEN DRIVING.

Posted by Anonymous on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

Possible bad master cylinder or air trapped in the system. Take it to a brake shop and have a power bleeding done on the system. Other possible causes could be low brake pads that have little sensors built into them that have to be replaced at same time as the pads.

Posted on Dec 19, 2014

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

355ttrex
  • 249 Answers

SOURCE: the brake pad warning light

Nothing special just be carefull of the clip at the pad to chassis harness , they can be a bugger to get apart sometimes . Have a good look at the new one before you attempt to take apart the one one the car.

Posted on Jul 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have an audi a4 quattro 2005 convertible problem is 3rd brake light will stop working and than work again. i also get dash warning when it goes out. will replacing brake switch fix this. also 2nd issue...


The brake light issue isn't likely the the brake switch (since it sounds like your other brake lights are working properly). It's likely a bulb in the third brake light. When the filaments get old they sometimes lose and regain contact as the car vibrates on the road. Change the bilbs and see if the problem goes away. If it doesn't, look for a bad wire connection around the third brake light. Also, have someone verify the third brake light isn't working from the back of the car when you see the alert, it could be a bad sensor.

Jan 05, 2013 | 2001 Audi A4

1 Answer

2003 mercury mountaineer brakes locking up abs light is on


Possibly has a bad wheel speed sensor or has a problem with the ABS control module and/or pump. Need to have the ABS codes pulled by a service center. Also, some auto parts stores can pull codes and may be able to pull ABS codes.

Dec 12, 2012 | Mercury Mountaineer Cars & Trucks

1 Answer

How do i remove the sensor for the rear tailgate?


1) Locate and remove sensor.
The sensor is located under the drivers tail light. Unclip it from the body and then unplug it.

2) Bypass the tail light circuit.
Connect the tail light signal wire (Green) to the tail light wire (Green w/ Red Stripe). I recommend using wire tap in squeeze connectors that way you dont have to cut any wires.

3) Bypass the brake light circuit.
Connect the brakelight signal wire (Green w/ White Stripe) to the brake light wire (Red w/ Blue stripe) and the the 3rd brake light wire (Red w/ White Stripe). Again all three of these wires are to be connected together.

4) Throw away your broken Tail Lamp Failure Sensor
Do not plug your sensor back in. Doing so will cause the annoying orange lamp failure warning light on your dash to stay on. Leave it unplugged ant the light will stay off.

5) Test your work
Turn on your lights and make sure your tail lights work properly. Have a friend step on the brake pedal, and make sure your brake lights work properly as well. Dont forget to check the Third brake light.

Sep 20, 2012 | 2002 Chrysler Voyager

1 Answer

Fuses panel described in English


Hope this helps your out. I know the diagram and locator is a bit blurry but hopefully it gets what you need.
Drivers kick panel:
Front wiper 20A - Front wiper system Cigar 15A- Cigarette lighter Audio 10A- Audio, remote control mirror Air Bag 10A -Air bag diagnostics Stop lights- 15A -Rear brake light, high mounted stop light ECU B+ 10A - Shift lock actuator, transaxle controle module, radio, engine control module Room 10A - Interior light, clock, ignition key reminder, rear cargo area light switch ABS 10A- Anti lock brake system control unit ECU IG1 10A - Transaxle control module, shift lock actuator, ABS control unit, DRL unit Meter 10A - Instrument panel, back-up switch, electronics time control module, inhibit switch Turn signal 10A- Hazard switch ,front and rear turn lights, turn indicator IGN1 20A - Ignition switch ABS 30A- ABS pump motor TNS 30A- Tail light, license plate light COOL/FAN 30A- Cooling fan Cond/Fan 20A- A/C condenser fan Starter 15A- Start signal , Fuel pump Blower 25A- Blower Motor SR/ACC 10A - Ignition switch Hazard 15A - Hazard and turn signal light D/Lock 25A- Door locks ABS 30A - Anti lock brake system control P/W RH 20A- Power window motor right hand P/W LH 20A- Power window motor left hand IGN2 25A- Ignition Switch
Engine compartment :
Head 25A- headlights IG 2 30A- Ignition switch IG coil 15A -Ignition coil, condenser,generator IC regulator, diagnostic connector. O2 down 10A- Rear O2 sensor O2 up 10A- Front O2 sensor Fuel pump 10A -Fuel pump unit Injector 10A -Fuel injector ,camshaft positioning sensor, purge solenoid valve, EVAP, IAC actuator, Mass Airflow sensor, EGR stepper motor. fuel pump relay coil, vehicle speed sensor. A/Con 10A - A/C compressor controls, cooling fan BTN 30A- Brake light , high mounted stop light. Tail light LH 10A- License plate light, tail light , rear combo light, instrument panel illumination Tail light RH 10A-License plate light, tail light , rear combo light, instrument panel illumination Head low 15A- Headlight Head Hi 15A-Headlight Horn 15A- Horn jlmacman.png jlmacman_0.png

Inside kick panel jlmacman_1.png

Mar 07, 2011 | 1995 Kia Sephia

2 Answers

My abs light just came on what is it to do with my car


probaly got debris in wheel sensor take off wheels and blow out

Feb 12, 2011 | 1995 Ford Aerostar

1 Answer

1994 Honda Passport,anti-lock and brake lights come on after about 5-10 seconds,brakes work great,Ive checked most connections,if you pull the park brake with engine running the brake light in the dash...


It may be that the brake system is contaminated with moisture, rust, or both. Bleed out or purge out all old brake fluid as a precaution, use a hand pump vacuum unit if possible to purge old fluid if not available thoroughly bleed out the system. The other possibility is that one of the reluctor sensors located behind the rotor's splash guard may loaded with dirt or just be faultly, purchase an ABS reluctor pick up sensor for the wheel that you think might be the culprit and change it out.

Nov 11, 2009 | 1994 Honda Passport

1 Answer

Light brake doesn't work-light on ant-lock brake


you need a rear left circuit board. they come with new lights, and is generaly inexpensive20-30 dollars

May 24, 2009 | 2003 Pontiac Montana

2 Answers

TURN RT APPLY BRAKES ABS/TRAC OFF COMES ON


bad front bearing/abs sensor The sensor is part of the bearing,or the wires are bad so that when you steer it open circuts and thinks the wheel is stopped. need to read codes or use a scan tool with live data to see which wheel the computer thinks is stopping. then look at that wheel for problems

Apr 25, 2009 | 2002 Pontiac Grand Prix

1 Answer

I have a 1998 town and country with traction control and the brakes drag after a few miles most notably the left front(smoke and melt caliper). I have replaced the calipers and rotors twice but this still...


I had a similar problem with my anti-lock brake.
One of the will wear down. I took it to the dealer, could not tell why.
Until one day the a brake light came on. It was a bad sensor. Replace the bad sensor and the problem went away.
The mechanic plug a portable instrument and drive the car around until he find out. (The brake light came on, then off.)
This anti-lock brake system is control by sensors and it one is not functioning properly then you have a problem.
I do hope this help you.

Mar 10, 2009 | 1998 Chrysler Town & Country

2 Answers

Anti lock brake light


abs relay some times go bad

Dec 05, 2008 | 1999 Oldsmobile Alero

Not finding what you are looking for?
1999 Mercedes-Benz S-Class Logo

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...