Question about 1995 Dodge Intrepid

1 Answer

I have the same problem in 95 intrepid

I actualy clunks i changed the drive shaft and still clunks i thingk i have tu to change the stub shaft

Posted by on

  • herodestrigu Jun 21, 2009

    i looked at it but it doesnt move i removed the drive shaft and the stub shaft is wearing out doy you konw if i can just by that with out buying the whole tranny repair kit

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Does it clunk when you accelerate only ? if so you need new engine mounts. To make sure, open your hood and observe the engine movement when pressing the gas pedal while in drive(other foot on the brake of course )

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi, when i'm coming off the third and the second gear mainly the 2nd gear it makes a clanking noise


My first thought here is your drive shaft u joints, but only because I've been stranded more than once by these. The higher torque of second will definitely make a worn u-joint "clunk". with the window down listen carefully as you engage and release your clutch in 1st gear, if you here any "clunking" noise I would check your u-joints. To do this SAFELY;ie, using jack stand etc. get under your car and try to turn the drive shaft by hand with the car in gear. ANY play in the drive shaft is bad. I'm not sure if you meant you've changed your clutch and the pressure plate or you did change out you flywheel. either way whichever you did not change could definitely be warped.

Nov 20, 2011 | Cars & Trucks

1 Answer

How to remove front axle on a 2002 dodge intrepid


raise you vehicle on jackstands. remove front wheel and tire.remove front caliper from steering knuckle assembly, remove rotor from hub by pulling it staright off. remove speed sensor bracket from strut assembly. remove hub and bearing to stub axle retaining nut. dislodge inner CV stub shaft retaining ringon transaxle assembly. insert small pry bar between transaxle case and inner CV joint by prying on it.remove strut assembly to steering knuckle bolts remove top of steering knuckle from strut assembly, then rotate CV assembly out of vehicle. Remove inner shaft from transaxle stub shaft grasp inner CV joint and interconnecting shaft and pull both pieces out at the same time. good luck!

Oct 30, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

Daewoo lanos how do i replace the cv gaiter please


Hi, most hyundai's you just undo the large drive shaft nu in the centre of the wheelnutst, the 2 bolts securing the strut(shocker) to the stub axle, sometimes you have to pop the tie rod end as well & even the inner control arm bolt, turn the stub full lock so you can get the shaft out through the back of it, then lever the shaft out of the diff with a screwdriver. Usually you have to pull the shaft appart to change the rubber boot, you'll need circlip pliers for this & it's pretty self explanatory which end to pull appart. It's a good idea to clean the grease off first so you can see what you're doing, good luck, hope this helps :)

Apr 20, 2010 | 1999 Daewoo Lanos

1 Answer

S-10 Clunk Sound


Possible U joint on drive shaft, give it a wiggle, or look for rust around one of the joints

Mar 28, 2010 | 1995 Chevrolet S-10 CA Edition

1 Answer

Clunking noise when outting 95 jeep in gear


that will be worn u joints
grab the drive shaft and wiggle it by all u joints and see what ones have excessive play and replace them

Mar 07, 2010 | 1995 Jeep Cherokee 2 Door

1 Answer

1999 dodge intrepid, transaxle 42LE


your cv joint is getting bad you will need to replace it

Nov 02, 2009 | 1999 Dodge Intrepid

1 Answer

When it goes in gear it maks a clunking sound


Check your motor mounts. They tend to seperate and allow the engine to raise under a load.

Sep 14, 2009 | 1994 Dodge Intrepid

3 Answers

2.2 95 cavalier front clunking noise when turning


Check your CV joints and then your struts.

Apr 27, 2009 | 1995 Chevrolet Cavalier

1 Answer

95 f-250 right front stub shaft removal


I think if you put a pry bar behind the knuckle and give it a quick bump it will just pop out it has a ring on the inside that holds it in. Just uses pressure to keep it in place I will look in a few but I am sure that is what to do.

Jan 02, 2009 | 1995 Ford F250

Not finding what you are looking for?
1995 Dodge Intrepid Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...