Question about 1996 Honda Accord

1 Answer

How to replace clutch slave on 1996 honda accord

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

First brake loose the line that feeds the slave cylinder. you will need a line wrench for this. then remove the 2 twelve millimeter bolts that hold the slave to the trans. remove the hydraulic line from the slave. reinstall in the reverse order(before installing slave break loose the 8 mm bleeder screw) then bleed the clutch by yourself or with an assistant. bleeding processes vary

Posted on Apr 25, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What could cause a clutch pedal in a 1996 honda accord to lost pressure


no fluid in the clutch reservoir due to a failed clutch slave cylinder
time to replace both the clutch slave and master cylinder

Dec 02, 2017 | 1996 Honda Accord

1 Answer

I put a slave cylinder in a year ago, a new clutch in august, an three master cylinders since then an my clutch is still engaging then disengaging when the pedal is on the floor, what could the problem be?


I have always found the slave bleeding instructions inadequate. The way they design the slave with the bleeder away from the piston makes the standard bleeding ineffective. Unbolt the slave and put a wrench on the bleeder nut. Hold the slave in your left hand with your thumb over the pusher. Open the bleeder with your right hand and push the piston into the slave. Close the bleeder, release the piston, and repeat until air is out. This is essentially a bench bleed on the car.

jturcotte_351.gif

Nov 29, 2010 | 1996 Honda Accord

1 Answer

97 honda Ex Accord Standard Transmission. Having problem shifting into 1st or reverse when starting up car. while going down road it shifts fine. week prior same problem, told son to check fluid level,...


problem is in the hydraulic clutch system
low fluid indicates a leak at the slave cylinder and not holding pressure indicates a leak at the slave cylinder or in the clutch master cylinder
If the master cylinder and slave cylinder have not been replace in side 5 years ago , the have them replace by a specialist brake and clutch shop
at this point there is nothing wrong with the clutch proper

Nov 27, 2017 | 1997 Honda Accord

2 Answers

I have a 96 honda accord and changed the clutch master cylinder and the slave cylinder and bled the system there still is no clutch pressure


You need to PRE BLEED the master cylinder, or you may never get pressure. Parts houses sell little hoses for this purpose.

May 30, 2010 | 1996 Honda Accord

1 Answer

1996 accord with manual trans won't shift into gear


could be clutch slave or master cylinder at fault but check clutch pedal first to make sure pedal mounting bracket has not broken

Dec 06, 2009 | 1996 Honda Accord

1 Answer

Trying to find clutch slave cylinder on 1996 Honda Accord.


go to napaonline or to local napa store part 37889 nnc. should run around 22.00

Sep 10, 2009 | 1996 Honda Accord

1 Answer

Bleeding Clutch Cylinder with no bleeder screw


I have not tried myself but see if the link below will work for your case. It is not the same model as you have but most vehicles have the same components for the non electronic parts. http://www.2carpros.com/forum/1988-dodge-dakota--bleding-air-out-of-clutch-master-cylinder-vt248517.html

Jun 04, 2009 | 1996 Honda Accord

1 Answer

1996 honda accord clutch goes all the way to the floor


check the slave and clutch master cylinder for leakage. look under the dash , at the clutch master) push rod attached to the clutch pedal) . try to see if there are any leaks around it. if so have it replaced and have the system bled to remove all fluid and air stuck in the system.

Apr 04, 2009 | 1996 Honda Accord

1 Answer

Sticky clutch


slave cyl is sepreate from master cyl you have air in the clutch hydraulic system replace slave and inspect clutch master for leaks on drivers floor board area pull carpet back and make sure to bleed system properly!!!!!!!

Feb 26, 2009 | 1992 Honda Accord

2 Answers

Bleeding clutch slave cylinder


i think youre doing the right thing. they are very stubborn to bleed because the hyd. line goes up high across back of engine before droppiing back down to slave cyl., trapping air. could try to gravity bleed by opening bleeder at slave, cap off of master cyl, full with fluid then it may start to come out after a bit. then try your process again. or can try to bleed at connections further up the line, working your way back to bleeder. hope this helps. be patient.

Nov 15, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

889 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...