Question about Chrysler Imperial

Open Question

Headlight covers won't close - Imperial Chrysler Cars & Trucks

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I repair 1989 oldsmobile toranado headlights


if there are vacuum operated look for leaks or damage to covers or just out of alinement

Oct 03, 2014 | Cars & Trucks

1 Answer

Need motor for 1990 olds toronado headlight covers.Where can I find one?


You may be able to find one on eBay. Have you checked the relays for the motor? There is one to open and one to close.

Sep 21, 2014 | 1990 Oldsmobile Toronado

1 Answer

Headlights not working


It's grounding out after there open trace the wires looking for exposed or broken wires. Or run new wires

May 02, 2013 | Cars & Trucks

1 Answer

How to change headlight on 2000 galant


  • 1
    Place the Mitsubishi on a flat service in park. Set the parking brake before continuing.

  • 2Open the Galant's hood and locate the headlight cover -- roughly 3-inch wide circular piece of plastic -- behind the headlight bulb intended for replacement. Turn this cover clockwise to unlock it and pull it from the headlight assembly, exposing the headlight socket below it.


    3

    Hold the rear of the headlight socket and turn it counterclockwise to unlock it. Pull the headlight socket and bulb from the headlight assembly.


    4

    Grab the bulb and pull it from the socket with a slight wiggling motion.


    5

    Pick up the new 9003 headlight bulb using a clean, lint-free cloth and line up its prong with the slots in the socket. Never tough the bulb with your bare hands, as the oils left by your hands can cause the bulb to burn out prematurely.


    6

    Slide the socket and new bulb into the headlight assembly and turn the socket clockwise to lock it into place.


    7

    Place the plastic cover behind the bulb and turn it counterclockwise to lock it into place.


    8

    Repeat Steps 1 through 7 for the headlight bulb on the other side of the Galant, if needed.


    9Close the Galant's hood.


    Read more: How to Put in a Headlight Bulb on a 2000 Mitsubishi Galant ' eHow.com http://www.ehow.com/how_8210819_put-bulb-2000-mitsubishi-galant.html#ixzz27iQwCdOe

    Sep 27, 2012 | 2000 Mitsubishi Galant

    1 Answer

    Illistration on how to change a headlight bulb


    HEADLIGHT REMOVAL AND INSTALLATION
    SEALED BEAM HEADLIGHTS REMOVAL 1 When replacing the headlight,do not turn the spring-loaded adjusting screws or the headlight aim will be changed 2. Remove the cover over the headlight this vehicle has five screws securing the cover other models may have four or six screws. 3. Remove the four screws which secure the retaining ring around the headlight support the headlight as this is done. 4. Pull the light away, unplug the connector and remove it from the vehicle. INSTALLATION 5. Position the new unit close enough to connect the wires. Make sure the numbers molded into the lens are at the top. 6. Install the retaining ring and mounting screws. 7. Install the plastic cover to the headlights with the screws you took off and check for proper operation. If the adjusting screws (spring - loaded adjusting screws) were not turned, the headlight should not require adjustment.

    Jan 17, 2012 | 1993 Oldsmobile Cutlass Ciera

    1 Answer

    Need to replace headlight?


  • Open the hood of your Crossfire to gain access to the headlight assemblies. Press down on the tab on top of the light assembly cover. Remove the cover and set it aside.
  • 2 Pull the electrical connection free of the bulb socket. Press the spring clamps securing the bulb into the light assembly. Pull the bulb straight out of position.
  • 3 Insert the new bulb in the same position. Ensure that the spring clamps secure the bulb. Press the electrical connection into place.
  • 4 Replace the light assembly cover and press it into position until it clicks, securing it in place. Repeat the same process on the opposite headlight if required. Close the hood and test the headlight I would replace them both sides if i were you
  • Dec 02, 2010 | 2004 Chrysler Crossfire

    1 Answer

    I am having problems with my 1988 Chrysler New Yorker motorized headlight covers. Both headlight covers don't close completely when I shut the headlights off. There is about 3 inches to go on both...


    I have the same problem with my 93 Salon. Take a look at the torsion bar rod end close to each headlight.There are collars that have a set screw which can be loosened to adjust the range of the door opening and closing. If the doors are going through the full cycle open to close but fall back and leave a gap such as you describe, most likely you will only need to adjust those screws. Each door will require adjustment individually. May require an allen wrench. Hope this helps.

    Aug 11, 2010 | 1988 Chrysler New Yorker

    1 Answer

    How to replace headlight bulb? Looks complicated.


    From MidSouth Tech Tips:
    1. Before you try removing the headlight housings, check for a blown fuse first, since the headlight circuits on these cars are fused. The fuse is located on the regular fuse panel inside the car, on the left side of the dashboard behind the removable cover.Well, since there are no visible screws anywhere around, how do I get the headlight out? It’s not that hard at all.
    2. Open the hood. Locate the seam between the nosepiece and the front fender (either side). Go up between the first two fender mounting bolts and look down a few inches. See a small knob sticking out at you? That is a release lever for the headlight assembly. Push in on it slightly and pull all the way up as far as the lever will go.
    3. Now push on the headlight from behind with one hand and be prepared to catch the assembly with the free hand from the front. It may take a bit of a push because there is some gooey adhesive between the headlight and the fender.
    4. Once you have the headlight out, pull the connector off the back of the housing and take the headlight somewhere where it is easy to work on. Put it on a pillow or something soft so you don’t risk scratching the lens.
    5. There is a black plastic cover on the back of the housing. See a tab on it? Push on this tab and pull the cover down to expose the bulbs.
    6. There is a metal spring clip that holds these bulbs in place. Undo this and the bulb will fall out. Take out the new bulb and compare it with the one you are replacing. Make sure the wattage is correct, since they are both H1 bulbs.Never touch the glass part of the bulb itself with your fingers.
    7. Use the soft cloth to handle the bulb if needed. Line up the tabs of the bulb base with the slots in the reflector housing and drop the bulb in. Put the spring clip back on and make sure the ends of the clip are in securely. Put the bulb cover back on.Now is the time to clean up the mess around the fender where the headlight mounts. Remember seeing that nasty-looking goo seep out from around the rubber seal on your headlights? That’s the adhesive I was talking about earlier.
    8. Take the adhesive remover on the paper towels and remove this stuff from the fender before putting the headlight back in. Don’t remove all of it from behind the headlight itself, as it is there to keep excess amounts of water from getting behind the headlight. Just remove enough to where it won’t make a mess anymore. A little wax around the mounting area on the fender will detail things out nicely.
    9. Position the headlight up to the fender. Push on the wire connector. Line up the tabs on the headlight assembly to the slots in the headlight housing in the fender and push the whole thing in. Sometimes things won’t line up on the first try, but keep trying. The headlight should go up against the fender fairly easily.
    10. Once you get it to this point, grab the release lever, push all the way down, and lock the headlight assembly into place.
    All you do now is test the lights. That’s it! The headlight aim should not have been affected during this procedure. Some wax or glass cleaner will be good for cleaning the lenses and make them sparkle again. If you have those trick blue bulbs or other colors, always keep a spare bulb handy, of the same color and manufacturer, so you won’t be stuck with odd colors until you get the right replacemen

    Oct 01, 2009 | 1999 Volkswagen Beetle

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chrysler Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Chrysler Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...