Question about 2004 Mitsubishi Colt

Open Question

Need to split mitshubishi colt 2.8tdi engine and gearbox for engine overhaul

How to split clutch Leed to remove engine for overhauln

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
shanat
  • 359 Answers

SOURCE: removal of evo6 gearbox

is the bellhousing removable? also check the flex plate isnt bolted on

Posted on May 24, 2008

Ad
  • 170 Answers

SOURCE: what gearbox oil for 1992 K reg Mitsubishi colt

IT IS SEPERATE FROM ENGINE THERE IS A FILLER BOLT AT FRONT OF BOX DRAIN PLUG IS AT THE BOTTOM NEAR THE OUT UT SHAFTS DRAIN IT AND REFILL WITH A SYNTHETIC CASTROL AUTO TRANS FLUID THIS WILL IMPROVE YOU GEAR SHIFTS

Posted on Sep 10, 2009

Testimonial: "Very grateful for reply to my query. Reply in mins. I had tried looking for a reply to my question online without success. Thank you."

  • 6 Answers

SOURCE: removing a pull type clutchsystem

what happen to my post ?

Posted on Apr 03, 2010

  • 17 Answers

SOURCE: removing clutch from mitsubishi legnum 2000

You need to remove a joining shaft between gear box and transfer there is a threaded end on shaft use a puller to extract and then transfer will come off.

Posted on Apr 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Clutch , presure plate and gearbox remove


You need the right equipment and knowledge to do this job there are a lot of cables wires etc that need to be removed before the gearbox can be loosened and removed.
There are also a lot of special tools required and the job is best done on a ramp or pit to gain access.
Trying to do this on the ground would be difficult and very dangerous also the engine needs to be suspended when the gearbox mounts are removed.
It is impossible to remove the clutch pressure plate, plate and hydraulic bearing on the C4 without removing the gearbox.
Take it to a garage/ clutch specialist.

Dec 26, 2013 | Citroen C4 Cars & Trucks

1 Answer

Clutch actuater probs on 2005 mitshubishi colt easytronic


a colt jeep, do send photos, we love frankencars.

Aug 12, 2013 | 1995 Jeep Wrangler

1 Answer

I need to know how to replace the clutch in a 1993 colt vista


0900c1528004723e.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Clutch release bearing - 1990 Colt hatchback and sedan w/ 1.6L engine, 1990 Colt Wagon w/1.8L engine, and 1990-93 Vista


0900c1528004723f.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Clutch driven and drive discs - 1990-93 all models


0900c15280047240.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Clutch release bearing - 1990 Colt Wagon w/1.5L engine, 1991-92 Colt hatchback and sedan w/4-speed and 1993 Colt hatchback and sedan w/1.8L engine

  1. Remove the transmission or transaxle as outlined.
  2. Insert a pilot shaft or an old input shaft into the center of the clutch disc, pressure plate, and the pilot bearing in the crankshaft.
  3. With the pilot tool supporting the clutch disc, loosen the pressure plate bolts gradually and in a crisscross pattern.
  4. Remove the pressure plate and clutch disc.
  5. Clean the transmission and clutch housing. Clean the flywheel surface with a non-oil based solvent. Wash your hands before installing or handling the clutch assembly parts. Hold the clutch disc by the center hub only.

Before assembly, slide the clutch disc up and down on the transmission input shaft to check for any binding. Remove any rough spots with crocus cloth and then lightly coat the shaft with Lubriplate.
  1. To remove the throwout bearing assembly: Remove the return clip and take out the throwout bearing carrier and the bearing.
  2. To replace the throwout arm use a / 16 in. punch, knock out the throwout shaft spring pin and remove the shaft, springs, and the center lever.
  3. Do not immerse the throwout bearing in solvent; it is permanently lubricated. Blow and wipe it clean. Check the bearing for wear, deterioration, or burning. Replace the bearing if there is any question about its condition.
  4. Check the shafts, lever, and springs for wear and defects. Replace them if necessary.
  5. If you hadn't planned on replacing the clutch disc, examine it for the following before reusing it. Loose rivets. Burned facing. Oil or grease on the facing. Less than 0.3mm left between the rivet head and the top of the facing.
  6. Check the pressure plate and replace it if any of the following conditions exist: Scored or excessively worn. Bent or distorted diaphragm spring. Loose rivets.
  7. Insert the control lever into the clutch housing. Install the two return springs and the throwout shaft.
  8. Lock the shift lever to the shaft with the spring pin.
  9. Fill the shaft oil seal with multipurpose grease.
  10. Install the throwout bearing carrier and the bearing. Install the return clip.
  11. Grease the carrier groove and inner surface.
  12. Lightly grease the clutch disc splines.

The clutch is installed with the larger boss facing the transmission.
  1. Support the clutch disc and pressure plate with the pilot tool.
  2. Turn the pressure plate so that its balance mark aligns with the notch in the flywheel.
  3. Install the pressure plate-to-flywheel bolts head-tight. Using a torque wrench and, working in a crisscross pattern, tighten the bolts to 11-15 ft. lbs.
  4. Install the transmission or transaxle as outlined.
  5. Adjust the clutch as described in the following information.

Jan 07, 2013 | Cars & Trucks

1 Answer

How to change a clutch on citroen xsara picasso


You have to remove cables, cooling pipes, gearbox lever links and driveshafts first, then get engine with gearbox out of engine bay.

Jan 18, 2012 | Citroen Xsara Cars & Trucks

1 Answer

My clutch gets noisy once i push on it before hitting a gear.. and i have an unstable idle, it goes up and down and sometimes my engine automatically turns off.. help please.. thanks.. by the way, my car...


It sounds like the thrust bearing has collapsed causing the noisy clutch. This means a gearbox removal and clutch overhaul. The rest is a case of a service and a tune up. but the important thing is the clutch.

Mar 05, 2011 | 1997 Honda Civic

3 Answers

Spiffire pops out of 3rd gear when decelerating


linkage too tight clutch going bad not enough fluid if hydraulic or low trans mission fluid levels check these areas 1st

Sep 24, 2009 | 2006 Triumph Tr 7

1 Answer

What gearbox oil for 1992 K reg Mitsubishi colt


IT IS SEPERATE FROM ENGINE THERE IS A FILLER BOLT AT FRONT OF BOX DRAIN PLUG IS AT THE BOTTOM NEAR THE OUT UT SHAFTS DRAIN IT AND REFILL WITH A SYNTHETIC CASTROL AUTO TRANS FLUID THIS WILL IMPROVE YOU GEAR SHIFTS

Sep 10, 2009 | Mitsubishi Colt Cars & Trucks

1 Answer

Mitsibishi colt 97 stuck in 1st gear


Your link broke off. What might have happened is the car got stuck in 1st, and when you shifted to second, the link broke. Not too clued up on your car, but you probably need to drop the gearbox. On some cars you can take out the shifter without having to drop the box and still see if the link is broken. Good luck

Mar 18, 2009 | 2006 Mitsubishi Colt

1 Answer

Clutch vibrating


Two reasons for this. Rattling is usually faulty pressure plate which means clutch overhaul. Depending on which Focus some have a rubber mounted flywheel which dies and must be replaced. Either way its gearbox out and check. First check all gearbox and engine mounts, but it sounds more serious.

Jun 30, 2008 | 2003 Ford Focus

2 Answers

Removal of evo6 gearbox


is the bellhousing removable? also check the flex plate isnt bolted on

May 18, 2008 | 2004 Mitsubishi Lancer Evolution

Not finding what you are looking for?
2004 Mitsubishi Colt Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...