Question about 1986 Chrysler Fifth Avenue

Open Question

Power ignition coil 318

No spark from plugs

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 457 Answers

SOURCE: how do i replace spark plugs and ignition coil

this has to be the 2.4. your coil is fine, just replace the plug and cable.

Posted on Mar 05, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

It mayI have no fire going to the coil or from the coil to the plugs


Have you checked the wiring, the spark @ plug, Power to the coil???

Engine Won't Start No Spark - Auto Diagnosis Repair Help

aa1car.com/library/no_spark.htm
If your engine cranks normally but will not start because it has no spark, or it ... If an engine has a coil-on-plug ignition system with no plug wires, remove one of ...

No-start, No-Spark diagnosing simulated - YouTube

? 5:13
https://www.youtube.com/watch?v=XSWN1M8Hoqo
May 19, 2010 - Uploaded by FrankHurtAuto
Simulation of no start with no spark diagnosing, ... Ignition coiland module test with test light (ScannerDanner Premium lecture) - Duration: ...

getting fire from coil but not to plugs - CarGurus

www.cargurus.com > Questions > Dodge > Ram 1500

CarGurusJun 12, 2013 - 2000 dodge ram 1500 4x4 not getting fire changed distributor cap, coil, pickup ignition, rotor, plugs, plug wires 2 answers. ... 1994 dodge 5.9 just shut off and wont start back up there is no spark or fire from coil or plugs. ... 94 dodge van 318 eng will not start new plugs new crank ...

Ignition Coil Troubleshooting: (No) Fire in the Hole

www.secondchancegarage.com/public/coil-troubleshooting.cfm

Jan 27, 2016 | Cars & Trucks

2 Answers

I have a 1990 Dodge Ram 150 with the 318 engine that the coil isnt sending fire to the dist...But the coil is good. Could someone help?


Could be a bad coil, or a bad pickup coil inside the distributor, or worst case a bad pcm.

You said the coil is good, but didn't mention if you had tested the coil's primary and secondary circuits with an ohmmeter to see if they are within specs? And the pickup coil is like a crank position sensor: it tells the pcm crankshaft position and rpm so the computer can determine spark timing.

Dec 19, 2014 | Dodge Cars & Trucks

3 Answers

No spark on the plugs of 318(m40)


you don`t say what year this is so I will guess this has a distributor, check for power at the ignition coil and coming out of the coil on the wires. then check for spark coming out of the coil. check the distributor cap and rotor for cracks and burn areas that will allow the spark to go to ground and not the plugs.

Aug 21, 2014 | Cars & Trucks

1 Answer

I installed ECM unit & ignition coil still no spark to plugs,


try the pick up coil inside the distributor

Jun 09, 2012 | 1986 Dodge D150

1 Answer

On the coil how many volt is a coil should have on poistiveside whenswitch is on it have 6.2volt when swith on 12 volt when the ecu is disconnect it have 12 it will not start an run it 318


A standard ignition coil normally generate about 15,000 - 25,000 volt depending the requirement to spark the spark plugs. The input volt should be 12 volt but the amperage should run about 400Va.
So now what is the question?

Nov 19, 2010 | 1983 Dodge Pickup

3 Answers

1992 dodge 318 engine turns over, but no start. No spark present. Replaced ignition coil and pickup coil, still no spark. 1992 dodge ram 150 full size truck 318 engine. starts sometimes then wont start...


if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

May 09, 2009 | 1992 Dodge Ram 150 Club Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...