Question about 2005 Toyota Tundra SR5

1 Answer

Unable to remove harmonic balancer pulley on camaro z28 v8

How to remove harmonic balancer pulley off camaro z28 v8 that absolutley will NOT come off

Posted by Anonymous on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 18 Answers

Wheel puller will do the trick....

Posted on Mar 02, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1779 Answers

SOURCE: 95 corolla harmonic balancer

It's a pain to fix. U do have to replace the entire harmonic balancer. For a description of what is involved, go to autozone website, enter your vehicle info, click on products and how to, then the letter H for harmonic balancer. Good luck!!! Curt

Posted on Dec 06, 2008

blueextc3221
  • 15935 Answers

SOURCE: which is number one piston on 4 cyl 1995 camry

Left (see diagram)
49b48f0.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 18, 2009

  • 163 Answers

SOURCE: front crankshaft seal, 1989 hilux

Hello,

Yes, it's possible to change the seal after removing the balancer.
If the balancer shows signs of scratching, wear at the place of the seal, change that part too!

To remove the old seal, drill 2 small opposite holes in the seal flange ( there is metal in it ).
Screw 2 (parker) screws in the holes, so you can pull the seal out gently.
Grease the new seals' inner race, and put some sealant paste to the external race.
Push it back in place with a wooden piece ( drill a hole in the center for the crankshaft end )
Grease the outher race of the balancer. This will help the seal come gently into place.

Good luck!

Posted on Nov 01, 2009

c1apton15
  • 3400 Answers

SOURCE: Torque settings for water pump

18ft lbs for waterpump bolts & 80ft lbs for balancer bolt

Posted on Feb 21, 2011

  • 126 Answers

SOURCE: how do i take the

u will have to go to a parts store ie. auto zone and rent a puller for this it's looks like a steering wheel puller

Posted on Apr 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm trying to remove a harmonic balancer. I've got to the point of taking it off. The pulley remover is placed. But the bolt when completely down only turns the balancer. How to fix please


Are you using a gear puller or an actual harmonic bal. puller? You can use air tools(carefully), or to hold the balancer/pulley still, use a chain wrench with an old belt wrapped around to prevent damage. I would not recommend a 2 or 3 jaw type gear puller.

Oct 17, 2015 | 1996 Buick LeSabre

1 Answer

Harmonic balancer remove replace


i dont think is your harmonic balancer that dont make any sound check all the pulleys cose to change the harmonic ba... you havto remove and change your crank pulley along with it

Jan 29, 2014 | Plymouth Cars & Trucks

1 Answer

Why is it hard to get balancer pulley off 98 neon? Tried a pulley puller and impact. Still no luck. What should I do?


Did you take out the center bolt? You have to remove the center bolt, then use a harmonic balancer puller. Not the two or three armed pulley puller, but a harmonic balancer pulley puller-the pullers with jaws that hook around the outside of pulley can ruin a harmonic balancer.
Use the impact gun to remove the center bolt. You won't need an impact gun to remove the balancer pulley. The balancer puller will take it right off the crankshaft, no problem.

Jul 23, 2013 | Cars & Trucks

1 Answer

Unable to pull the harmonic balancer


need a harmonic balancer pulley you can rent them at your local auto part store

Feb 20, 2013 | 1999 Cadillac DeVille

1 Answer

The Serpentine belt keeps walking off the Crank shaft pulley by one rib as if the pulley moved away from the engine.. Is this where the harmonic balancer is. If so, is it difficult to change?


Before you change anything,,check and see if everything is in line..Also feel all the pulleys and make sure everything turns ok...If the powersteering pump has been replaced,,sometimes the pulley was not pressed on far enough..If it seem to be the harmonic balancer make sure its not damage and the bolt in the middle is tight...If you remove it..You remove middle bolt,,then you have to use a puller to remove the harmonic balancer itself..unusuall for the harmonic balancer to be bad unless it was hit by something

Sep 20, 2011 | 2005 Ford Taurus

1 Answer

How much would it cost to replace a crankshaft position sensor for my 1996 chevy z28 5.7LT1


THE PART IS NOT THAT EXPENSIVE.YOU CAN JACK THE CAR UP AND LOOK UNDER THE HARMONIC BALANCER ,ITS RIGHT THERE 1 BOLT HOLDS IT IN.

Aug 28, 2011 | 1996 Chevrolet Camaro

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

2 Answers

I am unable to remove the crankshaft pulley on my 1999 ford taurus


the crankshaft pulley is also called the harmonic balancer.At any parts house checker,autozone,ect. will have the tool you need.It is called a harmonic balancer puller and bolts to the pulley and pulls it off.Let me know if this helped.

Jan 09, 2010 | 1999 Ford Taurus

2 Answers

Where is the crank sensor located on a 1999 oldsmobile intrigue 3.5 engine???? easy to replace or not...


usually all crankshaft sensors are located right next to the main drive pulley (Harmonic balancer). As far as being easy is concerned some are not so easy as some require the removal of the harmonic balancer to get to it.. but you might be lucky Gm is pretty good at making the Crankshaft sensor accessible without removing the harmonic balancer.

Dec 01, 2009 | Oldsmobile Intrigue Cars & Trucks

Not finding what you are looking for?
2005 Toyota Tundra SR5 Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...