Question about 2006 Ford Five Hundred

1 Answer

How to reprogram a key fob for a 2006 ford 500

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

  • Expert
  • 25 Answers

You are in luck! You can program a 2006 Ford Five Hundred key fob yourself and don't need to go to a dealer or professional. The steps are pretty easy, it's the timing of the steps that you have to pay attention to. You most likely will not get the programming correct on the first try, keep at it, you will get it.

Here are the key fob programming instructions for a 2006 Ford Five Hundred:
*** THERE ARE 2 POSSIBLE PROGRAMMING PROCEDURES. ***Procedure #1Note: Obtain all remote transmitters for this vehicle.
Note: Do not depress the brake pedal during procedure.

  1. Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. Door locks will cycle to confirm programming mode. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
  2. Within 20 seconds press any button on the first keyless remote to be programmed. Door locks will cycle to confirm programming. If you only have one remote then skip to step 4.
  3. Within 20 seconds, press any button on the second keyless remote. Door locks will cycle again to confirm programming. Repeat step 3. For all other remotes.
  4. Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

    Procedure #2Note: Obtain all remote transmitters for this vehicle.1Fasten seat belts and close all doors.
  5. Turn ignition from OFF to RUN 4 times within 6 seconds, with the 4th time ending in RUN. (Off is the position where you can remove your key, RUN is the position just shy of starting your car.)
  6. Turn ignition to OFF. Acoustic signal will sound and system warning lamp will illuminate to confirm programming mode.
  7. Within 10 seconds, press and hold any button on the first keyless remote. Wait for acoustic sound and warning lamp to flash (confirming programming) then release button on remote. Wait 2 seconds but within 10 seconds repeat step 4. For all other remotes. If you only have one remote then continue to step 5.
  8. Turn ignition to Crank or wait 10 seconds to end programming mode.
Make sure you have a spare key fob too. You can save a bunch of money ordering a spare key fob online at:
https://www.keylessentryremotefob.com/Ford-Five-Hundred-Remotes-and-Keys-s/5167.htm

Posted on Jul 12, 2018

  • Anonymous Jul 12, 2018

    hopefully he reprogrammed it 4 years ago

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: how do i reprogram my02 ford focus remote locking key fob please.

get in your car close door hit the unlock button then put key in the ignition cycle the key from off to on (STOP BEFORE START POSITION) cycle key off to on 7 times after the 7th trime the doors should lock the unlock automatically that means u are in trainning mode hit the unlock button on key fob. the key fob should now work if it doesn't then try changing batt

Posted on Nov 27, 2008

emissionwiz
  • 80531 Answers

SOURCE: key fob not working after battery change ford focus 2006

Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

Posted on May 28, 2009

bonedivers
  • 1140 Answers

SOURCE: one of my fobs and keys was stolen. I need to

Dealer only I think.

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: key fob stolen

You CAN reprogram it. You'll have to look for the exact directions, but it CAN be done. It has to do with turning the ignition to the RUN position a number of times, and then pressing one of the buttons on the existing fob. I just did it this past weekend. It worked!

Posted on Oct 19, 2009

fletch24990
  • 7 Answers

SOURCE: Do I have to reprogram a used ecm i'm putting on a 2006 ford focus?

I am not a mechanic but when we replaced one on my Moms Chrysler we were told all we had to do was disconnect it from the power source for 10 min and it would reset itself. Call you local dealer service department or parts department, they are usually pretty good about answering this type question.

Posted on Apr 05, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tire sensor fault on information center and drivers door will not unlock with remote key fob


Looks as though you have 2 separate issues here ,some vehicles but both may be related to a key fob reprogram.Do you have a second one to try and see if it is resolved.Look in you vehicle manual ,sometimes they have a section on how to reprogram them.

Dec 28, 2013 | 2006 Ford Escape

1 Answer

My wife had her purse stolen with one of the 2008 Expedition Keys and FOB's. How do I deprogram the keys and Fobs and reprogram just the ones I still have?


get two new fob e-bay is cheap or dealer cycle key from off to run NOT CRANK JUST TILL LIGHT COME ON . do that 8 times you door lock will lock then unlock this is key fob reprograming mode press unlock on fob door lock will cycle up and down then press unlock on other fob door lock will cycle again now start truck and shut off. test each fob.

when you reprogram the new fobs the other ones will not work

hope that helps

Jan 30, 2013 | 2008 Ford Expedition Eddie

1 Answer

Saab experts


May be keyfob needs reprogramming.

Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------




Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------



2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Dec 04, 2012 | Cars & Trucks

1 Answer

Peugeot 206 key fob


Try with brand new key fob battery and see.If that helps.
Otherwise May be keyfob needs to be reprogrammed.

KEYFOB PROGRAMMING


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.

If the remote s faulty then key fob will not get programmed.

Insert the key in ignition. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote.

These are just the basic procedure, but sometimes it will not help.

On that case dealer is the only option.


---------

There are few much related troubleshooting links mentioned below for remote key fob reprogramming. I suggest you to go through the list and click the link below to go through its details and procedure: -------

2009 Toyota Highlander: Smart Key Not getting Detected?

http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html


----------

2007 Toyota Prius: Reprogram Remote Keyfob?

http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html

-----------

Pin that holds the flick key part to the key fob?

http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html

-------------


2006 Toyota Hilux: Programming New Key?

http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html

----------

Where is Key chip memory located on 2004 ford Freestar?

http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html

----------

Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html

----------

After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure?

http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html

-----------

Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------

Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------

Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------

Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------

KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------

Mitsubishi Car Key Not getting detected after replacing ECM

http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html

-----------

Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------

2000 Jeep Cherokee Limited: KeyFob Remote Not Working?

http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html

-----------

Chevrolet Malibu: Key Stuck in ON position?

http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html

-----------

Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------

2012 Dodge Ram: Ignition Key will not release?

http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html

--------------


These details will help.

Thanks.

Nov 28, 2012 | Peugeot Cars & Trucks

2 Answers

How program the key remot


Keyfob remote reprogramming is not very difficult but on some cases it can be done by dealer service tools.If the remote s faulty then keyfob will not get programmed.Insert the key in ignition.Turn the key to on position,and cycle the key three times off-on-off-on-off-on.Then with the keyfob remote select your remote and then try to operate the vehicle with remote.These is just the basic procedure,but sometimes it will not help.
On that case dealer is the only option.
---------There are few very relted troubleshooting links mentioned below for remote key fob reprogramming.I suggest you to go through the list and click the link below to go through its details and procedure:-------
2009 Toyota Highlander: Smart Key Not getting Detected? http://whatisbyme.blogspot.in/2012/05/2009-toyota-highlander-smart-key-not.html
----------2007 Toyota Prius: Reprogram Remote Keyfob? http://whatisbyme.blogspot.in/2012/05/2007-toyota-prius-reprogram-remote.html
----------- Pin that holds the flick key part to the key fob? http://whoisbyme.blogspot.in/2012/07/pin-that-holds-flick-key-part-to-key-fob.html
-------------
2006 Toyota Hilux: Programming New Key? http://technoanswers.blogspot.in/2012/04/2006-toyota-hilux-programming-new-key.html
----------Where is Key chip memory located on 2004 ford Freestar? http://technoanswers.blogspot.com/2012/01/where-is-key-chip-memory-located-on.html
----------Ford Keyless Remote Fob Reprogramming?


http://schematicsdiagram.blogspot.com/2011/12/ford-keyless-remote-fob-reprogramming.html
----------After getting car washed, check engine light is ON and key less entry not working, tried reprogramming. Also car shows fuel pressure? http://schematicsdiagram.blogspot.com/2011/12/after-getting-car-washedcheck-engine.html
-----------Audi A8 Key Fob Programming?


http://technoanswers.blogspot.com/2011/12/audi-a8-key-fob-programming.html

----------------
Oldsmobile Aurora Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/olds-aurora-key-fob-reprogramming.html

-------------
Buick Lesabre Key Fob Reprogramming?

http://technoanswers.blogspot.com/2011/12/buick-lesabre-key-fob-reprogramming.html

---------------
Keyfob remote not working on 2003 Ford E350 Econoline?

http://technoanswers.blogspot.in/2012/01/keyfob-remote-not-working-on-2003-ford.html

-----------
KeyFob will open the doors but not start on BMW?

http://technoanswers.blogspot.in/2012/02/key-will-open-doors-but-not-start-on.html

------------
Mitsubishi Car Key Not getting detected after replacing ECM http://repairhelpcenter.blogspot.com/2012/11/mitsubishi-car-key-not-getting-detected.html
----------- Key Fob will not lock and unlock doors?

http://technoanswers.blogspot.in/2012/02/key-fob-will-not-lock-and-unlock-doors.html

-------------
2000 Jeep Cherokee Limited: KeyFob Remote Not Working? http://schematicsdiagram.blogspot.in/2012/06/2000-jeep-cherokee-limited-keyfob.html
----------- Chevrolet Malibu: Key Stuck in ON position? http://technoanswers.blogspot.in/2012/04/chevrolet-malibukey-stuck-in-on.html
----------- Theft indicator not letting car to start?

http://technoanswers.blogspot.in/2012/02/theft-indicator-not-letting-car-to.html

-------------
2012 Dodge Ram: Ignition Key will not release? http://whoisbyme.blogspot.in/2012/07/2012-dodge-ram-ignition-key-will-not.html
--------------
These details will help.Thanks.

Nov 23, 2012 | 2006 Toyota Tacoma

1 Answer

I can't open the car door with the key, i have to use the beeper but for some reason that is not connecting with the car (03 ford expidition). The car has two alarms, one i turned off with a key...


The key fob battery, the theft module , must be causing the problem.The car not getting open with key, may be key needs reprogramming.-------- There is a battery in a key fob, many a times battery gets weak or dead, causing the problem.But if battery in key fob is already replaced, then theft alarm needs to be reprogrammed by the dealer.The theft system is not letting the car to start.----------- Both key fob and theft module needs to be reprogrammed by the dealer.Its done by a reprogramming scanner.Not a error code scanned, but a reprogramming tool scanner.----------- That will only pin point the problem,if the theft module is got faulty or just needs reprogramming.---------- This will help.Thanks.Helpmech.

Sep 14, 2011 | 2003 Ford Expedition

1 Answer

My key fob has quit working and it tells me no key fob detected. My car is a 2006 Caddie STS. Both fobs have stopped working.


Mine did the same thing. I put the fob into the reprogramming slot located in the center console and was able to get it started by leaving the in the slot. Hope it works for you.

Sep 11, 2011 | 2006 Cadillac STS

2 Answers

Key fob not working after battery change ford focus 2006


Try reprogramming it.

1. Turn the ignition from OFF to RUN 4 times within 6 seconds.
2. Turn the ignition OFF. The system will chime to confirm programming mode.
3. Within 20 seconds, press any button on first keyless remote.
The system will chime once to confirm programming.

4. Within 20 seconds, press any button on second keyless remote.
System will chime once to confirm programming.

5. Turn ignition to RUN to exit programming mode.

May 28, 2009 | 2006 Ford Focus

1 Answer

The key of my honda 2006 does not work upon pressing lock and unlock button. I need to insert the key to the principal door to lock all the doors and activate the alarm. The trunk is locked as well. Any...


the key fob remotes need to be reprogramed or have the battery checked... make sure to have all key fob remotes present when reprogramming...

Apr 06, 2009 | 2006 Honda Accord

Not finding what you are looking for?
2006 Ford Five Hundred Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80531 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...