Question about 1996 Oldsmobile Cutlass Ciera

Open Question

3.1l v6 head bolt torque

What is the torque specs for head bolts

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
picatudo
  • 239 Answers

SOURCE: 1999 Oldsmobile Alero 2.4L.

75-85 lb

Posted on Jan 05, 2009

Ad

SOURCE: need to know cylinder head bolt torque specs

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. clearpixel.gif clearpixel.gif clearpixel.gif Foot pounds (Final torque) clearpixel.gif Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.

Posted on Feb 07, 2009

ddegroote
  • 35 Answers

SOURCE: 1995 Oldsmobile Cutlass Ciera SL 2.2 head bolts

you have long bolts and short bolts, long bolts go in positions 1,4,5,8,9 - short bolts remaining positions, all long bolts go in back of engine, toward fire wall or front of dash, those are positions starting at passenger side to drivers side, 8,4,1,5,9, so 1 is in the center position, 9 on drivers side. short bolts in front, positions passenger side 7, 3, 2, 6,10, stud is in position 10. Tighten bolts in sequence, starting at 1, long bolts get 32Nm, short bolts get 29Nm, next pass torque all to 58NM, than final pass add an angle of 100 degrees, little more than 1/4 turn with wrench. Bolts should have 11.9 on head, the tightening specification is called a torque plus angle to yield, that is why in your gasket kit is tells you to replace the bolts, it is recommended. I know, because I am the GM Manager for fastening engineering. Hope this helps

Posted on May 29, 2009

  • 1810 Answers

SOURCE: looking for head bolt torque specs on 2.2 ltr olds

chilton and haynes have a great bible for your car
chapters indago sell em cheep

Posted on Jan 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

I need the head bolt torque specs for a 94 bonniville with the 3.8l v6


A few notes. These head bolts are what are called torque to yield, this means they are like a spring and are only used once or the torque spec is not valid.
1ST 37 ft/lbs + 130 degrees OF BOLT ROTATION THEN REPEAT WITH 30 MORE degrees OF ROTATION. there IS NOT A SET TORQUE SPEC IN FT POUNDS

Feb 15, 2012 | 1994 Pontiac Bonneville

1 Answer

I need head bolt torque specs. for a 2002 ford f150 v6


Torque Specifications for Ford 4.2L-256ci-V6
These bolts are torque and turn procedure!
STEP 1: 14 FtLbs STEP 2: 29 FtLbs STEP 3: 36 FtLbs STEP 4: LONG Bolts Loosen 3 Turns - re-torque to 33FtLbs STEP 4: SHORT Bolts Loosen 3 Turns - re-torque to 19FtLbs STEP 5: ALL Bolts +180deg turn

Aug 05, 2010 | 2002 Ford F150 Regular Cab

1 Answer

Head bolt torques spec


3.8L V6

cylinder head bolt torque

step 1 37 ft lbs.

step 2 an additional 130 degrees

step 3 4 center bolts an additional 30 degrees

Jul 07, 2010 | 1999 Buick LeSabre

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

1 Answer

Head tourqe specs for 403 olds and bolt tightening


Fig. : Cylinder head torque sequence, 260, 307, 350 403 Oldsmobile built engines

5c04c01.jpg


On the V8, tighten the bolts, in the sequence illustrated, to 100 ft. lbs. When all bolts have been tightened to this figure, begin the tightening sequence again, and torque all bolts to 130 ft. lbs.

On V6's, tighten all head bolts in sequence to the following torques:
* All except bolts 5, 6, 11, 12, 13 and 14 - 100 ft. lbs.(19-135.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 41 ft. lbs. (19-55.5 Nm)
* All bolts except 5, 6, 11, 12, 13, and 14 - 142 ft. lbs. (19-192.5 Nm)
* Bolts 5, 6, 11, 12, 13, and 14 - 59 ft. lbs. (19-80 Nm)

9fb545e.jpg

Hope this help (remember comment and rated this).

Mar 29, 2010 | 1984 Oldsmobile Cutlass

1 Answer

I need the engine torque specs for 99 chevy malibu. like the head bolt torque sequence and rocker bolt torque sequence


99 chevy malibu v6 3.1 engine, head bolt torque is-- 98 through 2001 is step1- 37 foot lbs, step 2- rotate an additional 90 degrees (1/4 turn). the rocker arm bolts are 168-in. lbs.

Mar 12, 2010 | 1999 Chevrolet Malibu

1 Answer

1986 Mustang 3.8L cyl. head torque.


The aluminum heads on a cast iron block require some gentle torque procedures.... It may not be necessary - but I suggest that you start near the center of the head and work out with each tightening step. This will ensure that you don't put too much pressure on a single portion of the head. The standard proceedure for the 3.8 V6 up until 1994 is as follows:
You will have some long and some shorter head bolts. Place a small mark on the long bolts to identify them during the final torque proceedure.

Step 1: 15 (on all bolts)
Step 2: 29 (on all bolts)
Step 3: 37 (on all bolts)
Step 4: Now, starting near the center of the head, loosen a single head bolt about 2 turns. Now, torque it down to about 15 (+/- 3 lbs) IF A LONG BOLT.
OR 11 (+/- 3 lbs) IF A SHORT BOLT.
Step 5:
After all bolts are set as described above, ....go over them 1 more time, starting near the center of the head and pull each bolt down another 1/4 turn (90 degrees).
You are done!!

Oct 10, 2009 | 1986 Ford Mustang

2 Answers

NEED TORQUE SPECS AND SEQUENCE FOR 02 DODGE 2.4 V6 STRATUS


  1. Tighten bolts in sequence shown in (Fig. 23), using the following steps and torque values:
    • Step 1: Bolts 1 - 8 to 48 Nm (35 ft. lbs.)
    • Step 2: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 3: Bolts 1 - 8 to 75 Nm (55 ft. lbs.)
    • Step 4: Bolts 1 - 8 to +90° . Turn Do not use a torque wrench for this step.
    • Step 5: Bolts 9 - 11 to 28 Nm (250 in. lbs.)
  • I tried to send a pic of the head bolt numbers but it wont let me so e mail me dbern002@att.net have a good day DB

Feb 01, 2009 | 1997 Dodge Avenger

Not finding what you are looking for?
1996 Oldsmobile Cutlass Ciera Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...