Question about 1993 Ford Festiva

Open Question

Timing cover removal - 1993 Ford Festiva

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Easy to change a lower timing belt cover gasket on a 1990 Honda Accord


Depends on what you call easy and if you are mechanically inclined. First jack up the vehicle, remove the tire, remove the inner fender cover to accessthe balancer pulley. remove the drive belts, remove the crankshaft bolt and the remove the pulley. Then remove the bolts holding the lower timing cover in place. Install in reverse order. Average time to replace the cover is about 2 hours.

Feb 21, 2015 | 1990 Honda Accord

4 Answers

Removing the lower timing belt cover


  1. Raise and safely support the vehicle.
  2. Remove the engine under covers and drain engine coolant from the radiator; be careful not to allow coolant to contact drive belts.
  3. Remove the front right side wheel and tire assembly. Remove the engine side cover.
  4. Remove the drive belts from the engine.
  5. Rotate the crankshaft to position the No. 1 cylinder at the TDC of it's compression stroke.
  6. Remove the upper radiator hose and the water inlet hose. Remove the water pump pulley.
  7. Remove the idler bracket of the compressor drive belt.
  8. Remove the crankshaft damper. It may be necessary to use a puller to remove the crankshaft damper from the crankshaft.
  9. Remove the upper and lower timing belt covers.
  10. Make sure the punch marks on the camshaft sprockets align with the punch marks on the rear timing belt cover and the punch mark on the crankshaft sprocket aligns with the punch mark on the oil pump.
0900823d801f49c7.jpg
Fig. 1: Line up the punchmarks on the sprockets with the marks on the rear timing belt cover before removal of the belt

  1. Loosen the timing belt idler pulley bolt. Using a hexagon wrench, rotate the idler pulley to release it's tension and remove the timing belt.
0900823d801f49c8.jpg
Fig. 2: After the timing marks are lined up, loosen the tensioner and remove the belt

Be careful not to bend the new belt installing it. Timing belts are designed to flex only the way they turn around the pulleys.
To install:
After removing timing belt, do not rotate crankshaft and camshaft separately, because valves will hit piston heads.
  1. Confirm that No. 1 cylinder is at TDC on its compression stroke. Install tensioner and tensioner spring. If stud is removed apply locking sealant to threads before installing.
0900823d801f49c9.jpg
Fig. 3: Make sure the aligning marks are correct before installing the timing belt onto the sprockets

  1. Swing tensioner fully clockwise with hexagon wrench and temporarily tighten locknut.
0900823d801f49ca.jpg
Fig. 4: The tensioner uses a spring to aid in tensioning the timing belt. Be sure to use locking sealant when replacing the stud.

  1. Set timing belt, align the arrow on the timing belt forward. Align the white lines on the timing belt with the punch marks on all 3 pulleys.
There are 133 total timing belt teeth. If timing belt is installed correctly there will be 40 teeth between left and right camshaft sprocket timing marks. There will be 43 teeth between left camshaft sprocket and crankshaft sprocket timing marks

go to this link for more help
http://www.autozone.com/az/cds/en_us/0900823d/80/1f/49/c6/0900823d801f49c6/repairInfoPages.htm

Aug 25, 2008 | 1990 Nissan Maxima

1 Answer

Change timing belt


timing belt? on a Jeep? 05 wrangler
what engine is this>?
ah the 2.4L
front cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the crankshaft vibration damper.
  3. Remove the generator drive belt tensioner assembly.
  4. Remove the timing belt front cover bolts, and remove the covers.


rear cover
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the front covers.
  3. Remove the timing belt.
  4. Hold the camshaft sprocket with Special Tool 6847, or equivalent, while removing the center bolt.
  5. Remove the timing belt idler pulley.
  6. Remove the rear cover fasteners and remove the cover from engine.

Apr 04, 2014 | 2005 Jeep Wrangler

2 Answers

Noise in the timing chain


May be its problem with timing chain and it has to be inspected and replaced.Or its possible that timing chain is got misaligned.

There are few help,links provided related to timing chain assembly and dis-assembly. Go through it and confirm proper inspecting of timing chain.

Click the required help link below:----How to Replace Timing Chain Cover & Seal on Audi A4 ? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-timing-chain-cover-seal.html
----------1982 Toyota Pickup: Set ignition timing, engine overheating, timing chain issue, dist off? http://whatisbyme.blogspot.in/2012/05/1982-toyota-pickup-set-ignition.html
----------How to Remove Timing Chain Cover and Seal on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-cover-and.html

--------


How to Remove Timing Chain and Gears on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-and-gears-on.html

-------


Ford Mondeo ST220 camshaft Timing specifications? http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
------------Replacing Timing Chain Cover For 2009 Ford?

http://repairhelpcenter.blogspot.in/2012/03/replacing-timing-chain-cover-ford-2009.html


-----------
Timing Chains & Front Cover Removal on 2008 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/timing-chains-front-cover-removal-on.html
----------How to Replace Timing Chain Cover, Chain, Sprockets, & Seal On Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-cover-chain.html
---------How to Replace Timing Chain & Sprockets on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
---------Timing Chain & Sprockets Replacing on Ford, Mercury and Lincoln? http://fordrepairhelp.blogspot.in/2012/03/timing-chain-sprockets-replacing-on.html
----------How to Replace Timing Chain & Sprockets on Ford Edge and Lincoln MKX? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
------How To Replace Timing Chain, Sprockets & Front Cover on Ford Expedition and Lincoln Navigator? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets_356.html
---------Timing Chain, Sprockets, Front Cover & Seal removal for Ford Mustang? http://schematicsdiagram.blogspot.in/2012/03/timing-chain-sprockets-front-cover-seal.html
---------How to Replace Timing Chain on Buick LaCrosse? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-on-buick.html
---------These details will help.For more help keep updated.Thanks.

Oct 15, 2012 | Cars & Trucks

2 Answers

Need timing gear marks for 2004 Kia Sadona 3.5L engine



Removal & Installation

3.5L Engine

  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Record the radio anti theft code data.
  3. Remove or disconnect the following:

    Negative battery cable Engine cover Accessory drive belts Idler pulley Crankshaft pulley Power steering pump pulley Belt tensioner pulley Upper and lower timing belt covers
  4. Support the engine with a floor jack and remove the engine mount.
  5. Rotate the engine to align the camshaft sprocket timing marks with the cylinder head cover timing marks.

    0996b43f8022cb71.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt routing and timing marks-3.5L Engine

  6. Remove or disconnect the following:

    Auto tensioner Timing belt

    0996b43f8022cb72.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Timing belt and related components-3.5L Engine


To install:
  1. Ensure that the engine is set to Top Dead Center (TDC).
  2. Prepare the auto tensioner for installation by compressing it in a vise and installing a retaining pin.
  3. Install the timing belt in the following order:
    1. Crankshaft sprocket
    2. Idler pulley
    3. Left bank exhaust camshaft sprocket
    4. Left bank intake camshaft sprocket
    5. Water pump pulley
    6. Right bank intake camshaft sprocket
    7. Right bank exhaust camshaft sprocket
    8. Tensioner pulley

  4. Install the auto tensioner. Do not remove the retaining pin at this time.
  5. Check that the crankshaft and camshaft timing marks are aligned correctly.
  6. Rotate the crankshaft 1 / 4 turn Counterclockwise .
  7. Rotate the crankshaft 1 / 4 turn Clockwise to return the engine to TDC.
  8. Loosen the tensioner pulley center bolt.
  9. Apply 44 inch lbs. (5 Nm) torque to the tensioner pulley as shown and tighten the center bolt to 32-41 ft. lbs. (43-55 Nm).

    0996b43f8022cb73.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Adjusting the tensioner pulley-3.5L Engine

  10. Remove the auto tensioner retaining pin.
  11. Rotate the crankshaft 2 revolutions Clockwise , then wait 5 minutes for the auto tensioner to adjust.
  12. Measure the auto tensioner rod as shown. If the measurement is not 3.8-4.5 mm, then repeat the belt tensioning procedure.

    0996b43f8022cb74.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Measuring the auto tensioner rod-3.5L Engine

  13. When the auto tensioner measurement is correct, install or connect the following:

    Engine mount Upper and lower timing belt covers Belt tensioner pulley Power steering pump pulley Crankshaft pulley Idler pulley Accessory drive belts Engine cover Negative battery cable
  14. Reprogram the radio anti theft codes.

    Kia_Sedona_2002-2006
    Timing Chain, Sprockets, Front Cover & Seal

    Print


    Removal & Installation

    3.8L Engine

    1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
    2. Record the radio anti theft code data.
    3. Remove the engine from the vehicle.
    4. Remove the drive belt. Remove the power steering pump. Remove the air conditioning compressor.
    5. Remove the alternator. Remove the drive belt idler. Remove the drive belt tensioner. Remove the water pump pulley. Remove the intake manifold.
    6. Remove the connector bracket from the left cylinder head cover. Disconnect the right ignition coil connector, condenser connector and remove the bracket.
    7. Remove the left cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    8. Remove the right cylinder head cover retaining bolts. Remove the cylinder head cover from the engine.
    9. Set the No. 1 cylinder to TDC on the compression stroke. Turn the crankshaft pulley and align its groove with the timing mark T of the lower timing chain cover.
    10. Check that the mark of the camshaft timing sprockets are in straight line positioning on the cylinder head surface. If not rotate the crankshaft 360 degrees. Do not rotate the engine counterclockwise.
    11. Remove the oil pan. Remove the crankshaft damper pulley. Remove the timing chain cover.
      NOTE Be careful not to damage the contact surfaces of the cylinder block, cylinder head and timing chain cover. Before removing the timing chain, mark the right and left timing chains with an identification mark based on the location of the sprocket because the identification mark on the chain for TDC can be erased.
    12. After compressing the timing chain tensioner, install a set pin. Remove the right cam to cam guide. Remove the right timing chain auto tensioner and timing chain tensioner arm.
    13. Remove the oil pump chain cover. Remove the oil pump chain tensioner assembly. Remove the oil pump chain guide. Remove the right timing chain.
    14. Remove the right timing chain guide. Remove the oil pump chain sprocket and oil pump chain. Remove the crankshaft sprocket, oil pump and camshaft drive gear.
    15. Remove the left cam to cam guide. Remove the left timing chain auto tensioner and timing chain tensioner arm. Remove the left timing chain.
    16. Remove the left timing chain guide. Remove the crankshaft sprocket and left camshaft drive. Remove the tensioner adapter assembly.

      0996b43f8020193b.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing chain and related components-3.8L Engine


    To install:
    1. Check the camshaft and crankshaft sprockets for wear and damage, replace as required.
    2. Inspect the tensioner arm and chain guide for wear and damage, replace as required.
    3. Check that the tensioner pin moves smoothly when the ratchet pawl is released with a thin rod.
    4. The key of the crankshaft should be aligned with the timing mark of the timing chain cover. This indicates that the piston is at TDC on the compression stroke.
    5. Install the tensioner adapter assembly. Install the crankshaft sprocket and left camshaft drive.
    6. Install the left timing chain guide and torque the retaining bolts 14-18 ft. lbs.
    7. Install the left timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, timing chain guide, exhaust camshaft sprocket, intake camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201924.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Left timing chain markings and installation: (D) exhaust camshaft sprocket (C) intake camshaft sprocket-3.8L Engine

    8. Install the left timing chain tensioner arm and torque the retaining bolts 14-16 ft. lbs.
    9. Install the left timing chain tensioner and torque the retaining bolts 7-9 ft. lbs.
    10. Install the left cam to cam guide and torque the retaining bolts 7-9 ft. lbs.
    11. Install the crankshaft sprocket, oil pump and right camshaft drive.
    12. Install the oil pump chain and oil pump sprocket. Torque the retaining bolt to 14-16 ft. lbs.
    13. Install the right timing chain guide. Torque the retaining bolts to 14-18 ft. lbs.
    14. Install the right timing chain. Be sure to install the chain with no slack between the camshaft and the crankshaft (crankshaft sprocket, intake camshaft sprocket, exhaust camshaft sprocket). The timing mark of each sprocket should be matched with the timing mark (color ink) of the timing chain at installation of the timing chain.

      0996b43f80201925.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Right timing chain markings and installation: (C) exhaust camshaft sprocket (B) intake camshaft sprocket-3.8L Engine

    15. Install the right timing chain tensioner arm. Torque the retaining bolts to 14-17 ft. lbs.
    16. Install the right timing chain auto tensioner. Torque the retaining bolts to 7-9 ft. lbs.
    17. Install the right cam to cam guide and torque the retaining bolts to 7-9 ft. lbs.
    18. Install the oil pump chain guide. Torque the retaining bolts to 7-9 ft. lbs.
    19. Install the oil pump tensioner assembly. Torque the retaining bolts to 7-9 ft. lbs.
    20. Pull out the pins on both the left and right hydraulic tensioners. Install the oil pump chain cover.
    21. Rotate the crankshaft two revolutions in the clockwise direction. Confirm the timing mark. Be sure to rotate the crankshaft in the clockwise direction.
    22. Apply sealant on the chain cover and on the cylinder head, cylinder block, and lower oil pan. Be sure these parts are free of engine oil and dirt.
      NOTE Before assembling the timing chain cover, the liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201926.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Sealant application (1 inch bead width)-3.8L Engine

    23. Apply sealant on the chain cover.
      NOTE The liquid sealant TB1217H should be applied on the gap between the cylinder head and block. The part must be assembled with five minutes after the sealant is applied.


      0996b43f80201927.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover sealant application-3.8L Engine

    24. Install a new gasket to the timing case cover.
      NOTE It is important that the dowel pins on the cylinder block and holes on the timing chain cover should be used as a reference in order to assemble the timing chain cover in the correct position.


      0996b43f80201928.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover gasket installation (A) gaskets-3.8L Engine

    25. Install the timing chain cover. Torque the retaining bolts in the proper sequence and to specification. The engine should not be started for at least thirty minutes after timing chain cover assembly.

      0996b43f80201929.jpg enlarge_icon.gifenlarge_tooltip.gif

      Fig. Timing cover bolt torque sequence and specification-3.8L Engine

    26. Install the timing case cover oil seal.
    27. Continue the installation in the reverse order of the removal procedure.

May 19, 2012 | 2004 Kia Sedona

1 Answer

How do you remove timing cover on a 2001 dodge durango 5.9


this thing, has a lot things to do. a certified technicians only can do the job. but if you wanna do it alone, here are some instruction(s) after removing the parts to have acces on it.
1. Remove the crankshaft pulley using the appropriate socket.
2. Remove the harmonic balancer using the harmonic balancer puller.
3. Loosen the oil pan bolts.
4. Remove the front two oil pan bolts--one on each side of the crankshaft--these two bolts help hold the timing cover in place.
4. Remove the timing cover bolts using the appropriate socket.
5.Pull the cover off the block.
6.Remove the seal from the timing cover using a seal puller(if it is your problem).
7. Clean the gasket mounting surfaces on the engine and timing cover with the scraper.
8. Smear a thin layer of silicone on the timing cover's gasket mounting surface.
9. Fit the gasket on the timing cover.
10. Install the timing cover and tighten the bolts to it's specified torque.
11. Reinstall the two oil pan bolts and tighten them to it's specified torque.
12. Reinstall the accessories in reverse order of removal.

Feb 19, 2012 | 2001 Dodge Durango

1 Answer

How i do the timing on my 87 subaru gl awd


It's a bit of a pain but here is what you set it to:


c17hydro_187.gif

Aligning the marks on the flywheel with the marks on the flywheel cover



c17hydro_188.gif

Driver side timing belt (No. 2) and No. 2 tensioner-1.8L engine




c17hydro_189.gif

Passenger side timing belt (No. 1) and No. 1 tensioner


  1. Disconnect the negative battery cable.
  2. Loosen the water pump pulley mounting bolts.
  3. Loosen the alternator mounting bolts and remove the alternator belt.
  4. Remove the water pump pulley bolts and remove the water pump pulley.
  5. Disconnect the electrical harness from the oil pressure switch.
  6. Remove the dipstick tube.
  7. Remove the crankshaft pulley.
  8. Remove the timing belt cover plate, if equipped.
  9. Remove the timing belt cover bolts on the left, right, and center covers.
  10. Remove the timing belt covers.
  11. Remove the rubber cover seal. Clean all mating surfaces.

To install:

  1. Install a new timing belt cover seal.
  2. Install the timing belt covers on the engine using the mounting bolts. Tighten the bolts to 48 inch lbs. (5 Nm).
  3. Install the timing belt cover plate, if removed.
  4. Install the crankshaft pulley, and tighten the bolt to 69-76 ft. lbs. (93-103 Nm)
  5. Install the dipstick tube.
  6. Connect the electrical harness to the oil pressure switch.
  7. Install the water pump pulley and loosely install the mounting bolts.
  8. Install the drive belt and adjust the tension as necessary. Tighten the alternator mounting bolts.
  9. Tighten the water pump pulley mounting bolts.
  10. Connect the negative battery cable.
// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 77; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

Jun 20, 2011 | 1987 Subaru Gl 4WD

1 Answer

How do i remove the timing belt cover off my 98 escort lx?


if you are only removing the timing belt cover 1st remove the negative battery cable from the battery, next remove the drive belt (alternator belt) and belt tensioner next remove the three nuts and three bolts from the timing belt cover then remove the cover, you mite have to finesse the cover a little to get it off from behind the crank pulley but it will come out .

Dec 29, 2010 | 1998 Ford Escort

1 Answer

Timing belt removal 94 mercury villager


Hi, Disconnect battery ground cable, then drain coolant. Remove accessory drive belts. Remove A/C compressor drive belt idler pulley (tensioner) bolts, then idler pulley (tensioner). Remove upper radiator hose bracket bolt. Loosen two upper radiator hose clamps, then remove upper hose and bracket. Remove coolant bypass hose between thermostat housing and intake manifold coolant outlet. Disconnect main wiring harness from upper front cover (timing belt) cover, then remove eight upper timing belt cover bolts, then the upper cover, Fig. 20. Raise and support vehicle. Remove right front wheel and tire assembly and splash shield. Use strap wrench tool No. D85L-6000-A, or equivalent, to hold water pump pulley while removing water pump pulley bolts. Remove water pump pulley from water pump. Remove crankshaft pulley. Remove five lower timing belt cover attaching bolts and the cover. Rotate crankshaft in a clockwise direction to align crankshaft and camshaft sprocket timing marks, Fig. 21. If timing belt is to be reused, mark direction of rotation. Loosen timing belt tensioner nut, then remove timing belt. CAUTION: With timing belt removed, avoid turning camshaft or crankshaft. If movement is required, exercise extreme caution to avoid valve damage caused by piston contact.
Take care

Jul 24, 2010 | 1995 Mercury Villager

1 Answer

Ifailed to get on tdc before removing old timing belt how do I get back in time so Icanreplacebelt.


This is the complete procedure from the service manual on how to replace the timing belt start to finish, start over to assure u get it right, if u mess up the engine will be damaged

Removal for 1.6L engines : ONLY 2006 to 2009 CARS


Engine removal is not required for this procedure.

1.Remove the engine cover.

2.Remove the RH front wheel.

3.Remove the 2 bolts and RH side cover.

4.Temporarily loosen the water pump pulley bolts.

5.Remove the alternator drive belt

6.Remove the air conditioner compressor drive belt

7.Remove the power steering pump drive belt

8.Remove the 4 bolts and water pump pulley.

9.Remove the 4 bolts and
timing belt2_bing.gif upper cover

10.Turn the crankshaft pulley, and align its groove with timing mark "T" of the timing belt cover. Check that the timing mark of camshaft sprocket is aligned with the timing mark of cylinder head cover. (No.1 cylinder compression TDC position)

11.Remove the crankshaft pulley bolt and crankshaft pulley

12.Remove the crankshaft flange

13.Remove the 4 bolts and timing belt lower cover

14.Remove the timing belt tensioner and timing belt.

15.Remove the bolt and timing belt idler

16.Remove the crankshaft sprocket

17.Remove the cylinder head cover.

(1)Remove the wire harness bracket

(2)Remove the ignition coil.

(3)Remove the PCV (Positive Crankcase Ventilation) hose and the breather hose from the cylinder head cover

(4)Remove the engine cover bracket

(5)Loosen the cylinder head cover bolts and then remove the cover and gasket.

18.Remove the camshaft sprocket.

Hold the portion of the camshaft with a hexagonal wrench, and remove the bolt with a wrench and remove the camshaft sprocket.

INSTALLATION:

1.Install the camshaft sprocket and tighten the bolt to the specified torque.

(1)Temporarily install the camshaft sprocket bolt

(2)Hold the portion of the camshaft with a hexagonal wrench, and tighten the bolt with a wrench
Tightening torque :78.5 ~ 98.1N.m (8.0 ~ 10.0kgf.m, 57.9 ~ 72.3lb-ft)



2.Install the cylinder head cover.

(1)Install the cylinder head cover and bolts
Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

(2)Install the engine cover bracket

(3)Install the PCV(Positive Crankcase Ventilation) hose and breather hose to the cylinder head cover.

(4)Install the ignition coil.

3.Install the crankshaft sprocket

4.Align the timing marks of the camshaft sprocket and crankshaft sprocket with the No.1 piston placed at top dead center and its compression stroke.

5.Install the idler pulley and tighten the bolt to the specified torque.

Tightening torque :42.2 ~ 53.9N.m (4.3 ~ 5.5kgf.m, 31.1 ~ 39.8lb-ft)

6.Temporarily install the timing belt tensioner

7.Install the belt so as not give slack at each center of shaft. Use the following order when installing timing belt.
Crankshaft sprocket →idler pulley →camshaft sprocket →timing belt tensioner

8.Adjust the timing belt tension.

(1)Loosen the tensioner pulley mounting bolt and apply tension to the timing belt.

(2)After checking the alignment between each sprocket and each timing belt tooth, tighten the mounting bolt and one by one.

Tightening torque :19.6 ~ 26.5N.m (2.0 ~ 2.7kgf.m, 14.5 ~ 19.5lb-ft)

(3)Then recheck the belt tension.
Verify that when the tensioner and the tension side of the timing belt are pushed in horizontally with a moderate force [approx. 49N (11lb)], the timing belt cog end is aprox. 1/2 of the tensioner mounting bolt head radius (across flats) away from the bolt head center.

4)Timing belt tension measuring procedure
(by a sonic tension guage)
Rotate crankshaft in clockwise direction to set 1st piston on top dead center (TDC) and rotate crankshaft in counterclockwise to 90° then measure the belt tension in the middle of tension side span (in arrow direction of above illustration) by free vibration method.


9.Turn the crankshaft two turns in the operating direction (clockwise) and realign crankshaft sprocket and camshaft sprocket timing mark.


10.Install the timing belt lower cover with 5bolts

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

11.Install the flange and crankshaft pulley, and then tighten crankshaft pulley bolt. Make sure that crankshaft sprocket pin fits the small hole in the pulley.

Tightening torque :137.3 ~ 147.1N.m (14.0 ~ 15.0kgf.m, 101.3 ~ 108.5lb-ft)

12.Install the timing belt upper cover with 4 bolts.

Tightening torque :7.8 ~ 9.8N.m (0.8 ~ 1.0kgf.m, 5.8 ~ 7.2lb-ft)

13.Install the water pump pulley and 4 bolts.

14.Install the power steering pump drive belt

15.Install the air conditioner compressor drive belt

16.Install the alternator drive belt

17.Install the RH side cover with 2 bolts

18.Install the RH front wheel.


Tightening torque :88.3 ~ 98.1N.m (9.0 ~ 10.0kgf.m, 65.1 ~ 72.3lb-ft)

19.Install the engine cover with bolts.


Tightening torque :3.9 ~ 5.9N.m (0.4 ~ 0.6kgf.m, 2.9 ~ 4.3lb-ft)

May 20, 2010 | 2006 Kia Sorento

Not finding what you are looking for?
1993 Ford Festiva Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...