Question about 1992 Toyota Pickup

Open Question

Power steering bracket diagram - 1992 Toyota Pickup

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a power steering mounting diagram for a 1981 chevy caprice


The pump will bolt to the bracket, then you will have two bracket bolts to the water pump and another bracket bolt to a bracket attached to one of the exhaust manifold bolts.

Dec 04, 2015 | Cars & Trucks

1 Answer

I need a diagram for the brackets that hold on the power steering pump on a 1986 suburban


I am sorry but we do not have the factory repair manuals that show this. You can download the manuals here for a small fee.

Nov 06, 2012 | 1986 Chevrolet Suburban

1 Answer

I need a diagram of the bracket positions & mounting of the Power Steering pump for a 1989 Dodge Dakota 2wd - 4cylinder 2.5


Yes there is complete guide available for power steering pump and bracket positions mounting.Its will all details and diagram and lot more details.Please click on link below.Check the details http://technoanswers.blogspot.com/2011/03/1989-dodge-dakota-2wd-4cylinder-25.html ------------------ In this link is complete guide for steering and suspension of 1989 Dodge Dakota 2wd - 4cylinder 2.5------------------ This should help. Thanks.Helpmech.

Mar 29, 2011 | 1989 Dodge Dakota 2WD

1 Answer

Alternator mounting diagram


1999-2005 To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • The negative battery cable
    • The windshield wiper system module cover (if equipped)
    • The fuel injector sight shield (if equipped)
  3. Rotate and secure the engine forward.
  4. Remove or disconnect the following:
    • The generator B+ terminal nut chev_vent_99-05-alt-ec.gif

    • The generator B+ lead
    • The generator electrical connector
    • The drive belt from the generator gm_mv_ven_altbolt.gif

    • The generator front bolt gm_mv_ven_altrear.gif

    • The generator rear bolts gm_mv_ven_altbrack.gif

    • The generator from the generator bracket and position the generator above the drive axle
    • The drive belt tensioner
    • The generator bracket
    • The power steering pipes from the power steering pipe retainer
    • The fuel pressure test port (schrader valve) cap from the fuel injector rail NOTE: Do not disconnect the power steering pipes from the power steering pump.
    • The power steering pump and reposition in front of the timing chain cover in order to provide access for the generator
    • The generator from the vehicle
To Install:
  1. Install or connect the following:
    • The generator to the vehicle into position above the drive axle
    • The power steering pump to the engine
    • The fuel pressure test port (schrader valve) cap to the fuel injector rail
    • The power steering pipes to the power steering pipe retainer (if removed)
    • The generator bracket
    • The drive belt tensioner
    • The generator to the generator bracket and position the generator above the drive axle
    • The drive belt tensioner
    • The generator to the generator bracket
    • The generator front bolt
      1. Torque to: 37 ft. lbs. (50 Nm)
    • The generator rear bolts
      1. Torque to: 37 ft. lbs. (50 Nm)
    • The drive belt
    • The generator electrical connector
    • The generator B+ lead
    • The generator B+ terminal nut
      1. Torque to: 115 inch lbs. (3 Nm)
  2. Position the engine rearward.
  3. Install or connect the following:
    • The engine mount strut bracket bolts
    • The fuel injector sight shield
    • The windshield wiper system module cover
    • The negative battery cable
prev.gif next.gif
for removal to reposition the engine

Feb 15, 2011 | 2000 Pontiac Montana

1 Answer

Where do I find a diagram to change the power steering pressure line hose in my 1990 Lincoln Continental?


REMOVAL

  1. Disconnect negative battery cable.
  2. Remove sight shield.
  3. Remove module bracket.
  4. Disconnect No. 6 spark plug wire to prevent damage to wire.
  5. Remove radiator fan shroud assembly.
  6. Remove top RH isolated radiator mount bracket.
  7. Remove remote air cleaner.
  8. Remove ignition coil.
  9. Disconnect electrical connector on power steering pressure switch at steering gear.
  10. Remove pressure switch to allow for tool clearance.
  11. Remove screw at pressure switch and return line bracket.
  12. Remove anti rattle clips from power steering lines.
  13. Remove plastic strap attaching steering gear heat shield to power steering return line.
  14. Remove plastic strap attaching lines to transfer tube on the steering gear.
  15. Disconnect Electronic Vacuum Regulator (EVR) valve wire.
  16. Remove the ground wire from back of engine block.
  17. Remove pressure line fitting at power steering pump using a 5/8 inch flare nut wrench.
  18. Loosen clamp and remove return line at pump.
  19. Loosen clamps and remove return line at power steering oil cooler.
  20. Remove pressure line fitting (gold in color) at steering gear, using an 18mm open end wrench.
  21. Remove return line fitting (silver in color) at steering gear, using an 18mm open end wrench.
  22. Loosen two screws retaining power steering oil cooler to sub frame.
7c30cde.gif

Oct 21, 2010 | 1990 Lincoln Continental

2 Answers

Need diagram of installation of power steering bracket on a 1995 gmc 1500 with a 5.0


I suggest visit autozone.com (free register) and check all the information about this subject in there.

Good luck.

Apr 01, 2010 | 1995 GMC Sierra C1500

1 Answer

1975 chevy c-20 truck power steering mounts


This is for 5.7L engine, hope that's yours.34cefcc.jpg

Jul 21, 2009 | 1983 Chevrolet Chevy

1 Answer

I broke timing belt when replacing hormonic balancer


Here are some. Hope it helps =D

Timing Marks

Diagram


TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Jun 28, 2009 | 1992 Honda Accord

1 Answer

Need the belt diagram for the water pump belt for a 95 Auroa


42161874BELT, REPLACE
  1. Release belt tension and remove belt from power steering and alternator pulleys. Twist belt to get between tensioner and front cover and between power steering pulley and engine mount bracket.
  2. Raise and support vehicle.
  3. Turn wheel to the extreme right and remove right side splash shield.
  4. Remove belt from crankshaft and A/C compressor pulleys. Twist belt to get between idler pulley and engine mount bracket.
  5. Lower vehicle.
  6. Twisting new belt to get past the front cover, install belt around power steering pump pulley, Fig. 15. Allow belt to hang free.
  7. Twist belt to get between tensioner and front cover, wrap belt around alternator.
  8. Remove belt from power steering pulley and set aside.
  9. Raise and support vehicle, then twist belt to get between tensioner and front cover, wrap belt around crankshaft and A/C compressor pulleys.
  10. Install right side splash shield and lower vehicle.
  11. Position belt around power steering pulley and release tensioner.

Nov 23, 2008 | 1995 Oldsmobile Aurora

2 Answers

Water pump assembly and power steerin pump brackets


need to know year? engine size?what accesories equipped? a/c power steer smog pump etc.

Aug 26, 2008 | 1989 Dodge Ramcharger

Not finding what you are looking for?
1992 Toyota Pickup Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...