Question about 2011 Chevrolet Chevrolet Cruze LT

Open Question

Replace rear view mirror

Need to tighten inside rear view mirror. How do you remove plastic cover?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2920 Answers

SOURCE: Need to glue rear view

they sell a rearview mirror adhesive you apply to the windshield in the spot you want to put it in any parts store carries it...its called rearview mirror adhesive

Posted on Aug 22, 2008

  • 69 Answers

SOURCE: I need to replace the Passenger rear view mirror on a 2002 Chevy

Use a long flat head screw driver with electrical tape wrapped around it(to prevent scratches). Have some one help you and hold a light so you can see the snaps on the inside, be really nice about it and pry the panel from the door frame.

Posted on Aug 21, 2009

Testimonial: "Thank you very much, great help."

dmsr63
  • 2050 Answers

SOURCE: 1993-2002 Camaro INSIDE REAR VIEW MIRROR REMOVAL?

There is a small screw in the mirror, an allen (or hex) wrench fits in it.

Posted on Sep 04, 2009

  • 593 Answers

SOURCE: remove inside door panel passenger side front to

to remove the panel they make special tools that make the job alot
easier available at most any parts store. that said there should a screw
that holds the trim piece by your door handal and then you will see nut
that holds it remove it this nut can also be located under the arm rest pad that should pop off make sure any door speakers are not mounted
through the panel if you have crank window one of the tools i mentioned
to remove the u shaped spring clip behind crank if you have pwr. windows there should be enough wire to pull it out + unplug it if not remove the trim plate + win. ctrl. the panel is held by spring clips use the other side of the window tool starting at the bottom work your way
accross + up both sides the clips will stay in the panel once yoe have poped all clips lift panel from sides over the top lip of the door + change
your mirror to put panel back line the clips up with holes + pop them in
make sure you pu the panel tool it's so much easier.
hope this helps good luck.

Posted on Jan 15, 2010

daltonp
  • 361 Answers

SOURCE: I need to replace the pass. side rear view mirror,

all of it. Its pretty easy just take your time there r blanks that cover the screws on the handles and bottom of the door. Best bet is to buy a Haynes workshop manual and read it

Posted on Apr 18, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear view mirror mounting hole cover (17K709)


The mirror is attached inside the door, you must remove the door panel, the part you think is just a cover doesn't come off.

Jun 13, 2016 | 2009 Ford F-250 Super Duty

2 Answers

How can I tighten my loose inside rear view mirror?


I don't think you can. You just have to replace it.

Jun 24, 2015 | 1995 Toyota Corolla

1 Answer

Wish to replace a rear view mirror on the passenger side of a 1992 honda accord wagon.


Behind the mirror on the inside of the door there will be a triangular shape piece of plastic, gently pry the plastic from the door, now that it is removed you will see a multi electrical plug for the mirror if you have electric mirrors, seperate the plug.
look in the small holes in the door where the plastic cover was removed and you should see 2 or 3 bolt heads, remove those bolts and the mirror should now be free to remove from the vehicle

Jan 29, 2011 | 1992 Honda Accord

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do you get the plastic housing open on the inside of the windshield? I see how the screw on the mirror fits in the bracket but can you "open" the plastic around it?


if your talking bout the rear view mirror its a flat piece of metal glued to your windshield and the screw tightens the mirror bracket to the small piece of metal once you loosen or remove the screw you should be able to slide the mirror bracket off i believe it slides downward hope this helps

Jan 03, 2011 | Hyundai Accent Cars & Trucks

1 Answer

How to replace Inside Rear View Mirror on 2000


Hello, to replace the rear mirror, try the following:

1. Roll the passenger side door window all the way down. Turn off the ignition and remove the keys.


2. Gently pry the window control panel from the arm rest with the pry tool or screwdriver starting at the bottom of the panel. Flip it over and unplug all the wire harness outlets from it. Set the panel aside.

3. Locate and remove the two panel door plugs near the arm rest concealing the two screws and remove the screws with the Phillips head screwdriver.

4. Remove the door panel retainer plugs along the edge of the door by pressing in the middle of the plug to unlock it and removing the plug.


5. Detach the mounting triangle from the upper inside door panel covering the side-view mirror.

6. Remove the door panel by lifting outward and then upward. Disconnect the speaker wire harness from the underside of the door panel and set the door panel aside.

7. Locate and disconnect the mirror wire harness.

8. Pull back the foam insulation from the inside panel covering the side-view mirror.

9. Unscrew the three mounting nuts from the mirror using the ratchet, extension and a socket. Do not drop the nuts into the door cavity.

10. Pry the mirror gently away from the outside of the door.

11. Install the new mirror and replace the mounting nuts on the mirror studs and tighten with the ratchet, socket, and extension. Plug the mirror wire harness back in. Replace the foam insulation. Replace the mounting triangle.


12. Replace the door panel by reversing the procedure. Start by plugging in the speaker wire first.


Thanks
































Jul 26, 2010 | 2002 Pontiac Grand Prix

1 Answer

Need a diagram for installing a drivers side electric power mirror on a 1995 mercury villager van


here's 1996, all I have. Please rate.

Mirror, Power — Outside Rear View NOTE: This procedure applies to both RH and LH power outside rear view mirrors.

Removal
  1. Remove the front door trim panel (23942). Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws and the outside rear view mirror mounting hole cover (17K709) from the front door (20124).




  1. Remove the wire clip.
  1. Disconnect the power outside rear view mirror electrical connector.




  1. Remove the three power outside rear view mirror bolts and the power outside rear view mirror.




Installation
To install, reverse the removal procedure. Tighten the three power outside rear view mirror bolts to 3-4 Nm (27-35 lb-in). Glass, Outside Mirror
Removal and Installation
Refer to the glass replacement procedures in Manual Mirror for power outside rear view mirror glass (17K707) Trim Cover
Removal
  1. Remove the front door trim panel. Refer to Section 01-05 for the removal procedure.
  1. Remove the two outside rear view mirror inside mounting hole cover screws.


    Remove the outside rear view mirror mounting hole cover.
Installation
To install, reverse the removal procedure. Mirror Control
Removal
  1. Use a small flat-blade screwdriver to pry the power outside rear view mirror control switch from the instrument panel (04320).


May 13, 2010 | 1995 Mercury Villager

1 Answer

How to replace rearview mirrors on yukon 1996


The replacement of outside rearview mirrors is straight-forward and can be done in an hour or so. If you need new power mirrors, first shop with local body parts suppliers in your area. The after-market mirrors are nearly identical and can be purchased for about $20-$30 per side. Remove the plastic triangular cover over the inside of the mirror by lifting up at base and then release clip at the top which is an upward motion off of a slot in the rear of the triangle. Then pull out the foam insulation carefully. The 3 nuts are 10mm and a long scket works best. For the one at the very front, you will have to use an open end wrench to loosen the nut. There is not much room for a socket. Be carefull to not drop the nuts down the inside of the door, because you don't want to remove the door panel and then the inner metal panel to get them out. If you lose them, buy new ones or replace with proper treaded ones in your garage. After the three nuts are off you need to disconect the wiring. Stop here and make sure you have enough slack in the wiring to be able to hold the female end securely, while you refit your new mirror. I took a piece of wire an dwrapped it around the female end to keep it within reach to re-attach the wiring after the nuts are tightened. Then just replace your foam insulation, and install the triangular cover and you're all set.

Nov 30, 2009 | 1996 GMC Yukon

Not finding what you are looking for?
2011 Chevrolet Chevrolet Cruze LT Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...