Question about Jeep Grand Cherokee

Open Question

Jeep 3.0 diesel mercedes engine cranks no injector pulse

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
polarcycle
  • 1392 Answers

SOURCE: no injector pulse, no current to the injector

Check the pickup in the distributor as this is the cam sensor. The injectors run of the pulses created while the rotor is turning around. It should be a plastic disk located under the rotor button.

Posted on Mar 13, 2009

Ad
  • 7 Answers

SOURCE: 99 ram diesel wont start

Did you check to see if there is power to the glow plugs if not then that may be the problem and if there is power when you cycle the key not to start but for the plugs to warm up you may have a bad glow plugs.

Posted on Apr 22, 2009

Molson02536
  • 3854 Answers

SOURCE: 1985 corvette no pulse to injectors

Very important that if you are not savvy of working on your Vette ...you would be better off - taking your car to a dealership for repairs on your trouble codes. However if you feel that you want to, First locate your car's alcl this component is located just below the instrument panel and to the left of the center console. Remove the plastic cover the first two slots to your right are the A & B slots.
The A slot is the diagnostic slot and the B slot is the ground slot. Insert the computer key into these slots if you do not have a computer key, a paper clip or wire jumper clip will do, (with the engine off) this is very important...now only put the ignition key to on ( not start !!!) the check engine light will display a code 12 which is one flash followed by two flashes. This code will be flashed three times ..followed by the trouble code stored in your car's computer.

What ever the code is it will be flashed three times. Have a paper and pencil ready and write down the code.

Code #12: Normal No Codes. 
Code #13: Open Oxygen Sensor Circuit. 
Code #14: Coolant Sensor Circuit Low.
Code #15: Coolant Sensor Circuit High. 
Code #21: Throttle Position Sensor High. 
Code #22: Throttle Position Sensor Low. 
Code #23: Manifold Air Temperature Circuit High.
Code #24: Vehicle Speed Sensor. 
Code #25: Manifold Air Temperature Circuit Low. 
Code #32: EGR System Failure. 
Code #33: Mass Air Flow Sensor High.
Code #34: Mass Air Flow Sensor Low. 
Code #36: Mas Air Flow Sensor Burn-Off Function Fault. 
Code #41: Cylinder Select Error. 
Code #42: Electronic Spark Timing.
Code #43: Electronic Spark Control. 
Code #44: Lean Exhaust indication. 
Code #45: Rich Exhaust Indication. 
Code #46: Vehicle Anti Theft Fault. 
Code #51: Faulty Mem-Cal. 
Code #52: Fuel Calpak Missing.
Code #52(1990-91 Corvette Only): Engine Oil Temperature Sensor Low. 
Code #53: System Over Voltage. 
Code #54: Fuel Pump Circuit Low Voltage. 
Code #55: Defective ECM. 
Code #62: Engine Oil Temperature Sensor Circuit High.

Please remember that if you have the computer key installed in the alcl and you start the engine (you will ruin the engine's computer) only put the ignition to on (not to start).

If you should get a check engine soon display.. you can use the above procedure and codes to buy the right part or at the very least to keep from getting taken for a ride and be made to pay hight prices for some inexpensive module that you could have installed yourself.

If your engine displays a trouble code ... your engine will go into limp mode ..it will still run but very poorly. You might be able to reset the computer if it will not start (just to get home) by disconnecting both battery cables and re-installing them ...this is not recommended ..but if you are stranded it might help unitl you get your car home or to a repair shop..good luck.

Good luck and hope this helps. 

Posted on May 08, 2009

  • 740 Answers

SOURCE: 1993 honda accord 2.2,no injector pulse

This sounds like a main relay problem here is a diagram its located under the dash under steering column its the brownish -orange box in the picture. http://www.tegger.com/hondafaq/mainrelaylocation/7-main_relay_closeup.jpg Good luck and thanks for using FIX YA

Posted on May 15, 2009

Larrysito
  • 73 Answers

SOURCE: diesel injector leaks air on 2002 jeep grand cherokee

There must by a copper ring if isnot under the jet it is y ....replace and tighten it .....

Posted on Jun 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

NO PULSE TO INJECTORS


wow, no plus
are we to guess how you know that>?
which engine, 3.7L? v6?
cant guess that either, we open hood first and look, omg its a diesel?
PULSE 101
  1. spark tips dry, way.?
  2. NOID lamp dead, x6 or just one.??????
  3. injector balance test shows all 6 injectors dead.
  4. ECU scans of pids shows PW at 0 mS.
  5. scope on injector pins, show 12vdc both pins. no plus.

be nice to know this and symptoms.
why not ask for trouble shooting advice?

engine runs at all?
or misfires
stalls.
what?
low engine power?

if not start?, does it start with test fueL and run for 3 seconds each time and repeats. ok>?
if yes, engines ok and spark if it sounds perfect. sounds matter.

Mar 18, 2016 | 2014 Jeep Compass

2 Answers

What causes no pulse to injectors?


Hi there can be a few things

1)Faulthy crank/cam position sensor
2)on diesel engine can be faulthy rail presure sensor cutting all 5v components
3)Broken off wiring
4)Ecu (engine control unit) Faulthy

Sep 18, 2015 | Cars & Trucks

1 Answer

2008 Jeep Grand Cherokee 3.0 Mercedes CRD will not start


does it start and run for 3 seconds on test fuel

yes, engine ok, EFI bad.

no, bad engine, engine must be good to run.

EFI cant run bad engines..

so compression at spec......????



why beat the EFI to death,

all engines run on test fuel.

with gas engines, takes spark and good engine

on diesel, takes only good engine. simple huh (and some air)



for test fuel try diesel in a spray bottle into the injection port.

google this

or use youtube on test fuel on any diesel car. or truck



this is called basics....... basic basics.

1: good engine, and pumps air ok. (must breath)

2: good fuel.

3: test fuel works now. if not check above.

May 09, 2015 | 2008 Jeep Grand Cherokee

1 Answer

Fuel injectors quit working


fuse power to rail injector must be good check fuses first.
is CEL glowing key ?
ok,no engine stated. this the 4 liter? I6? nah you said HEADS
not 2.5L I4
not 4.0 L I6
so must be V6, really
or the 2.1L diesel....>>>>
and 3 or 4 diffr. EFI systems, im not much help
why folks post engine free ,amazes me....

it takes 2 things.
fuel pressure over 30psi (generic)
and the noid lamp passing on injector.

and the knowledge that all jeeps,(cars) cut fuel (gas)
if the PCM see and errors with (crank for 5 seconds)
1: spark?
2: CMP?
3: CKP?
4: if IMMO , that too, no imm on 87, think , go lazy to look up.

If the NOID lamps fail x6 (no injection pulses)
then the ASD relay is dropping out)
87 is the really really old RENIX/Benicx injection system. on 4L
i had a 88. same car.
see alldata.com for permissive to inject.

on my old I6 4L Renix sys
the injectors are all grounded , that is correct
and the ECU drives this hot switched ! unlike most cars.
back then the ASD was called the LATCH relay.
if it dont pull in and stay , it will not run.

Ill stop there. until you say what engine and country car resides.
export jeeps are wired different (laws)

Feb 15, 2014 | 1987 Jeep Comanche

1 Answer

2004 jeep grand Cherokee fuel injectors stay open


If not pulsing, could be a bad pcm. The computer grounds the injectors internally for a split second to pulse them . If trash or debris is not making them stick open, buy a "noid light" for checking injector circuits. Plug it in to #1 or #5 and crank engine over: if circuit is working right, noid light will be blinking. If light is on steady, computer is not interrupting ground to cause pulsing.

Jul 11, 2013 | Jeep Grand Cherokee Cars & Trucks

2 Answers

Now the **** 1993 jeep does not start even after the asd and fuel pump relays click even though i have fuel pressure after the relays click w t f ???


If the check engine light never comes on, on the dash, with the ignition turned on, then the jeep will not start. You should try hooking up a noid light to the fuel injector wires, to see if the ecu is pulsing the injector while cranking. If the ecu does not send a pulse then the crank sensor or the ecu itself is bad and needs repair.

Oct 01, 2011 | 1993 Jeep Grand Cherokee

1 Answer

Detroit diesel injector installation


thoroughly clean area around injectors,and then blow with compressed air so no bits will fall in the holes when injectors removed.loosen main injector pipe nut,remove return fuel line,dont lose copper washers,put special fuel bolts back in top of injector firm[by hand] undo holding down bolts evenly,undo fully injector pipe nut,.gently pry injector loose,and remove,making sure sealing washer at bottom also comes out..while I dont specifically know this particular engine,this guide applies to most diesel motors.I have rebuilt a 6v72 detroit motor,yrs ago.Assembly is reversal.may need to crank over to bleed diesel at injector,always use new sealing washers.

Jul 01, 2010 | 1990 Mercedes-Benz 300 Diesel

1 Answer

Runs ok for 10 min then no inj pulse 2.5 engine this ditributor has no wires going to pick up coil is thi normal


I'm thinking the crank angle sensor is going out. I'd bet when you get no injector pulse, you loose fire too. that would tell me your crank angle sensor is gone.

May 27, 2009 | 1989 Jeep Wrangler

1 Answer

2001 jeep Grand Cherokee fuel injectors


check the injectors on that bank for pulses.. a regular 12v text light will do it should flash when cranking... its very possible that the crank sensor or camshaft sensor on the replacement engine is bad and giving you all the problems you have now.. are you using the original injectors? if you have injector pulses then check the coil for pulses the same way.. btw make sure you have 12v to them even before cranking engine could be a bad asd relay..wet plugs on one bank would also indicate a possible leaking injector and basicly draing the fuel starving the oposite bank for fuel.. to verify that the rail must be lifted by removing all 4 bolts make sure the clips hold the injectors firmly and turn the key to run but dont crank it then look for fuel leakin from bottom of injector(s) any drips is a bad injector..

Jan 28, 2009 | 2001 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...