Question about 1995 Jeep Grand Cherokee

1 Answer

Ignition problem with jeep

My jeep will not start.ignition will not turn over. all electrical items work but when key is turned to full position, electrial items turn off. they come back on is key is released slighty

Posted by on

  • Mike Butler
    Mike Butler May 11, 2010

    What happens with a boost?

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Howdy, several things come to mind, so here's a few things to check. most likely you have an automatic transmission, have you tried cranking in neutral instead of park? if you can crank it in neutral then the neutral safety switch/transmission range sensor could be your problem. also, when you turn the key to crank, do you hear the starter relay(in the underhood fusebox) or the starter solenoid clicking? the starter & ignition switch can also cause this problem. check all your fuses inside and under the hood. good luck.

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn on ignition jeep starts ok sometimes spedo and idicators wont work unless you move key adain while running


There could be some play in the ign switch allowing the voltage to be lost in certain position. Turn key to run position, do start engine. Turn on blower fan, turn signal, radio . Wiggle the key to see if they go off with key movement. If so replace electrical switch behind the key and tumbler

Nov 02, 2013 | Cars & Trucks

1 Answer

2009 Jeep Commander --- Ignition problems. For the past few weeks, roughly 75% of turning the ignition OFF from RUN, the ignition will not release the key. Need to turn ignition on and off (potentially...


Hey Anon, Is this a total electronic key,,(push button start)..if so, its an electrical issue. If its a standard key urn ignition. try some DRY graphite on the key.. it will lubricate the switch without the mess of liquids... put the key in and out several times, put some more dry graphite on the key and repeat.. give this some time to work,, if this does not improve the switch.. its time for a new switch assy,

Jun 24, 2017 | Jeep Commander Cars & Trucks

1 Answer

I have an air rush noise coming from under the hood of my jeep. it happens when i turn ignition on and its constantly going. it sounds like a gust of wind. any ideas as to what it can be?


Check if you have electric fans for the radiator as it may be them going in the run position. If the ac is left switched on then when in the run position of the ignition key the fan for the ac condensor may be starting up

Apr 22, 2013 | Jeep Liberty Cars & Trucks

1 Answer

Re program my key fobik for a 2011 grand Cherokee jeep


put program key in ignition turn ignition switch to on position engine off for 3 to 15 seconds.you should hear acoustic signal and immobilizer lamp will flash then turn off ignition switch.you need two program keys to do this procedure twice. with in sixty second insert non program key in the ignition switch turn to on position engine off for at least with ten minutes you should hear acoustic noise immobilizer lamp flashing turn off ignition switch if all failed the dealership have to use diagnostic equipment to reprogram ignition key or keys.

Oct 26, 2012 | 2011 Jeep Grand Cherokee

1 Answer

The security system locked the jeeps ignition but i dont know how to restart the system and i try to start it and it wont not even jumping it help


if you have both ' original ' keys that came with the Jeep - you can try and flip them through the system and get the Jeeps computer to accept them,, take both keys and sit in the drivers seat -- with one key put it in the ignition and turn to the on position - wait about 15 -20 seconds, remove the key and then put the other key in and turn to the on postion -- wait 15 to 20 seconds,remove the key and now put the first key back into the ignition and turn to the on postion and wait 15 to 20 seconds,,, now try and start the Jeep.
now if one of the keys is not an original key ( a clone key ) -- then this might not work,, and you will need a automotive locksmith to come out and re-program your keys to the Jeeps computer. since you already have keys, this is not a very expensive trip -- you will just be charged for the service call and the programming of the Jeep.

c...

Jan 05, 2011 | 2002 Jeep Grand Cherokee

1 Answer

I have an 1989 jeep comanche. It had an ignition switch bypass. I took it off and replaced the switch and the relay. If i touch the positive battery cable to the green starter wire on the relay it...


on the relay there will be a small wire that gets power when you turn the key to the start position
find that wire and connect it to the small terminal of the starter solenoid
then if you get it right , when you turn the key to start, power will get to the starter solenoid , energize the solenoid and the starter will engage

Jun 03, 2017 | 1989 Jeep Comanche

1 Answer

99 jeep wont start and the starter works battery is good what could be thew problem?


Even though it's called a starter, it's only job is to turn the engine so it can start. (technically you could call it an engine turning motor) You need to determine if you have fuel and spark. If you can hear the pump in the tank running when you turn the key on then the problem is most likely in the ignition system or crankshaft position sensor. To do any meaningful testing you need a chiltons (best) or haynes (ok) manual and a digital multi-meter made for testing those items that make your system operate..

Jun 19, 2010 | Jeep Grand Cherokee Cars & Trucks

2 Answers

My radio, wipers and blinkers all do not work. If


just renew the whole thing ignition switch and ignition barrel

Jan 23, 2010 | 1988 Jeep Cherokee

1 Answer

2002 jeep


If your battery is full charged I'd give a 90% chance your starter is the problem. Sometimes you can tap the starter with a hammer while someone has the ignition key in the start position and the starter will work. Also make sure your battery terminal connections are clean and tightend properly so the full power is able to reach the starter.

Dec 30, 2009 | Cars & Trucks

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

311 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...