Question about 2007 Chevrolet Matiz 1.0

Open Question

Matiz chevrolet can't take plastic covers off to replace brake lights

I cant get the plastic cover off the brake light housing?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 39 Answers

SOURCE: rear brake light and taillight out how to remove cover chevy subu

When you open the rear door there should be 2 screws in the door jam holding the tail light in.

Posted on Apr 09, 2009

  • 1 Answer

SOURCE: replace turn signal switch 1998 chevy lumina

You may look or feel the back side of the steering wheel, looking for 2 screws that hold the airbag to the wheel, these will be internal torq type screws (star) you may have to rotate the steering wheel 90 degrees to access the screws. You should first disable the airbag, by removing the airbag fuse, and or by disconnecting a yellow connector located near the base of the steering column. under the knee bolster.(panel below column). Once the retaining screws are removed, lift bag and disconnect the 2 connector to the airbag, the ground for the horn, and the horn contact wire, which requires you to push down and twist counter clockwise, damage to the horn contact ring will occur if you try and just pull connector from the ring. Now you can remove the steering wheel, may require a puller, and the you will have access to the turn signal switch.

Posted on Jul 20, 2009

  • 1986 Answers

SOURCE: 1994 chevrolet pickup - brake light problems

There will be an electronic flasher module located under your dash near the steering column (don't know it's exactly location as it varies). It sounds like this unit may be faulty.

Posted on Aug 21, 2009

c17hydro
  • 2984 Answers

SOURCE: Timing Chain Cover, Chain, Sprockets, replacement

2.2L VIN 4 To Remove:

  1. Remove or disconnect the following:
    • Drive belt.
    • Drive belt tensioner.
    • Alternator.
    • Power steering pump. Place the pump aside with the lines attached.
  2. Lift the vehicle.
  3. Remove or disconnect the following:
    • Oil pan.
    • Crankshaft pulley and hub.
    • Timing cover bolts.
    • Timing cover. If necessary, tap with a rubber mallet to loosen the cover.
  4. Clean the mating surfaces.
To Install:
  1. Install or connect the following:
    • Timing cover gasket.
    • Timing cover and the bolts. Tighten the bolts to 11 Nm (97 in. lbs.).
    • Crankshaft pulley hub and the crankshaft pulley.
    • Oil pan.
  2. Lower the vehicle.
  3. Install or connect the following:
    • Power steering pump.
    • Alternator.
    • Drive belt tensioner.
    • Drive belt.

Posted on Aug 30, 2009

  • 56 Answers

SOURCE: 2004 Chevrolet Aveo Brake lights not working

A couple of days ago my brake lights on my 2004 Chevy Aveo wouldn't work, so I attempted to remove the lamp covers to check the bulbs. Also, before this my shifter would get stuck in park and could only be released by pressing the unlock gadget next to the shifter. Back to the brakes...Well, you open the trunk and remove the two screws just like the manual said, but it was very hard to pull off. There's 2 prongs holding the other half of the light on. The lamp will come loose by prying it (very hard). You think the cover will break, but it'll come loose. The bulbs were all OK.

After much frustration and internet info, the STOP LAMP SWITCH, GM#96436331 ($9.30 at Chevy dealer), which is located under the dash and has contact with the brake pedal, was defective. Once replaced, both my brake lights AND SHIFTING problems were cured. So if the brake lights suddenly don't work or you have problems getting the vehicle out of park, check the switch by pushing the prong (end that has contact with brake) of the switch in and out. If it doesn't retract smoothly...that's the PROBLEM. Good Luck.

Posted on Sep 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the brake light bulb in 2010 Chrysler Sebring retractable hardtop


Open the trunk, remove the plastic jamb cover and then the interior cover from the inside of whichever side you want to remove, the remove the plastic wing nuts, and the tail lamp assembly should pop right out allowing you access to the bulb housings which twist lock in to the back of the housing. Hope that helped!

Nov 23, 2014 | Chrysler Cars & Trucks

1 Answer

Have a 94 cavalier wagon and want to replace headliner. problem is i cant figure out how to get the dome light housings off. there are no screws visable. might be rivited?


did u pop the cover off the dome light?..screws are usually under the cover, where u would access to change the light bulb

Mar 13, 2011 | 1994 Chevrolet Cavalier

1 Answer

2005 Cad CTS. Rear brake light went out. Now the blinker on the same side blinks rapidly. I bought the replacement bulb from Auto Zone and have been able to remove the light kit from the back of the car...


There's about four to six plastic knobs to remove cover facing rear end. Pull the spare wheel cover. On each side in the quarter panel remove plastice knobs. Pull back. Each light has two nuts, remove. Pull light covers and change. Took me a 30 minutes, had to clean out the trunk first :). Good luck!

Dec 01, 2010 | 2005 Cadillac CTS

1 Answer

Replacing middle brake light


some of these are done from the trunk, open trunk and look for socket if its closed in then just go inside car and gentle pry rear cover off third brake light housing, once cover is off you can change bulb and more more required then remove housing.

Aug 25, 2010 | 1998 Chevrolet Monte Carlo

1 Answer

Get inside upper brake light housing to replace lens cover


If there are no push pins (like a button with a button in it, VERY carfully hook soemething around it and pull back... GM likes to use cheesy metal or plastic blind fasteners

Sep 12, 2009 | 2000 Saturn Ls 4dr Sedan

1 Answer

Break light bulb replacement


The brake light bulb is accessed from inside the trunk. There are 2 plastic wing nuts that release part of it. Then you pull back the covering just a bit and there are 2 more. That should release the entire Light housing. A small turn and the bulb holder removes from housing. Hope this helps and have a good day.

Jan 31, 2009 | 1992 Chevrolet Cavalier

3 Answers

Replace headlight for 2005 Chev Trailblazer


59Shadow.
Thank you for sharing the information on the light bulb. You just saved me money from having to take my 2003 Trailblazer in to have the low beam bulb replaced. I did exactly what you said.
1 Open hood and lock.
2. Take filter cover off (4 screws and they stay with the filter).
3. 3 inch cover pulls off.
4. Twist light bulb 1/8 turn.
5. Unclip the wiring harness to light bulb assembly.
6. Test by turning light switch on.
7. Align assembly with light housing and turn 1/8 until it snaps in.
8. Put 3 inch cover back on.
9. Place filter cover back on and hand tight the 4 screws.
10. Close hood.

Dec 12, 2008 | 2005 Chevrolet TrailBlazer

2 Answers

Drivers Side brake light bulb is burned out.


Pull the panel back on the INSIDE of the car's hatchback or trunk. The bulbs twist in from the back.

Dec 03, 2008 | 1993 Ford Mustang

4 Answers

Replacing a brake light bulb for a 2006 chevrolet equionx


I just replaced the p/s brake light:
1. Pop off the tabs that cover the screws. (flat screwdriver)
2. Unscrew both screws. (philips-head)
3. There is a metal post attached to the light assembly located towards the front of the assembly pointing in towards the center of the car. This post fits into a rubber grommet that is attached to the car. I had to wiggle and rock the assembly to get the post free from the grommet and the assembly off the car, by pulling to the right.
4. Re-assembly requires lining up and inserting the post back into the grommet (use your best Beavis and ******** sound effect now). Put the screws back in and don't forget the covers.

Jun 20, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
2007 Chevrolet Matiz 1.0 Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...