Question about 1996 Nissan Pathfinder

Open Question

How to bleed hyundai I load clutch

Method to bleed hydraulic clutch in a hyundai iload diesel turbo van

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 5317 Answers

SOURCE: 1990 nissan sentra 1.8i 16v twincam coupe. clutchfluid is leaking at pedal

It can only be coming from the clutch master cylinder, the end that is bolted to the firewall, and that the push rod from your clutch pedal enters into. You will have to take it off for repair or replacement.

Posted on Apr 29, 2012

Testimonial: "thank you very much. I appreciate your time and expert advice u gave me. "

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2011 iload Diesel Turbo Auto is having a stalling issue.


same problem indicated on an isuzu diesel that turned out to be problem injector causing the ECM to shut down and then allow a restart-- no codes shown and the service center was stumped until a diesel repair shop checked it out and found an injector control was faulty
check for vent problem in the fuel tank starving the diesel for fuel

Nov 22, 2016 | Cars & Trucks

1 Answer

How to tighten up the clutch in a Hyundai accent 2000 model


You have a hydraulic clutch and there is no adjustment. If the clutch is spongie, try bleeding the clutch at the slave cylinder. Other than that, it may need replacing.

Oct 10, 2016 | Hyundai Cars & Trucks

2 Answers

How do I bleed a external clutch slave cylinder with no bleed screw on a 95 ford f250 turbo diesel


Need to remember that air rises. When replacing slave cylinder first hook everything up and bleed using the nut on the connecting line at the slave, then slowly depress and release pedal making sure to keep plenty of fluid in the reservoir, then after sitting a bit, tap on slave cylinder, line from bottom all the way up to the master, then loosen the nut connecting the line to the master and allow any air there to escape. Repeat whole process if needed.

Jan 05, 2015 | Ford Cars & Trucks

1 Answer

Ford Bantam rocam Clutch: How do I bleed the clutch?


Clutch bleeding on hydraulic slave cylinders are done in the exact same method as regular hydraulic brakes. If the slave cylinder has a separate reservoir, make sure it is above "MINIMUM" at all times. If it does not have a separate reservoir, then it works together with the master cylinder for the brakes, make sure that one is above minimum too. Pump the clutch pedal a couple of times (note you will rarely feel any resistance in the pedal), hold the pedal down, and have someone open the bleeder valve on the slave cylinder. Close it when no more fluid comes out with pressure, then rinse and repeat until the clutch pedal feels ok.

Jan 09, 2014 | 2006 Ford Bantam 1.6i

1 Answer

Hyundai Iload diesel won't start, have replaced engine in van with changeover from wrecker & it turns over but doesn't fire up


run the scanner to reset the ECM and immobiliser
make sure that the cranking speed is fast
check for air in the system
check that the stop solenoid is connected

Nov 03, 2012 | Hyundai Cars & Trucks

1 Answer

I have a 2001 holden rodeo turbo diesel and only just got the clutch and pressure plate replaced two days ago and now when you put your foot on the clutch it feels as though you are putting your foot on...


possibly air trapped in hydraulic clutch system causes pedal to go low and hard like brake pedal,
bleed from bleed nipple on firewall (bulkhead) under bonnet, left side of vehicle then under neath at slave cylinder.
when left for a while or turn vehicle off it comes good again due to air in line shifts position
these can be tricky to bleed also due to pedal doesnt come up when bleeding must pull up with foot or hand do it slowly and pump it for a while before opening bleeder nipple again.
hopefully you put the clutch fork in the right way again if you replaced the thrust bearing and the bearing itself depending on engine configuration.

Feb 03, 2011 | 2000 Isuzu Rodeo

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

The clutch is stuck down on hyundai 1998 wagon can anyone suggest how to fix?


inspect clutch linkage,hydraulic clutch system,oil level in master cylinder,if its low or empty,check for leakage from master to slave cylinder at transmission release lever,repair and bleed system at slave.

Mar 10, 2009 | 1998 Hyundai Elantra

1 Answer

Clutch pedal low near floor, can the clutch be adjusted?


hi the clutch on accent is hydraulic operation so if pedal is very low on disengaging clutch ? you may have a problem with the hydraulics 1st thing to check is fluid level? this is the reservoir that feeds both brakes and clutch but is seperaterated inside if fluid low? top up and bleed the slave cyl however if fluid low indicates a leak ? possibly slave cyl? if no loss of fluid ? then prob may be fault in the master cyl ? check fluid come back with any update please ps if this problem has just occured? check for leaks ?

Feb 02, 2009 | 2005 Hyundai Accent

Not finding what you are looking for?
1996 Nissan Pathfinder Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...