Question about 1989 Dodge Colt Vista

1 Answer

No power when in gear - 1989 Dodge Colt Vista

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Dodge Master
  • 987 Answers

Check air and fuel filter if you have not ck engine light on if light is on run scanner to retrieve codes

Posted on Apr 13, 2014

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace PS pressure hose on 95 Buick Roadmaster


Remove or Disconnect

Coolant recovery tank.
ECM cover.
Serpentine belt.
Power steering pressure line at pump.
Catch oil in drain pan.
Power steering pressure line at steering gear.
The pressure pipe is the lower line at the steering gear.
Use a 18 mm crow's foot line wrench with a 2 foot, 3/8 inch drive extension.
Access line from engine compartment, between the rocker arm cover and front of dash mat.
Raise and suitably support vehicle.
Steering gear heat shield bolts and heat shield.
Power steering gear line clamps at steering gear.
Power steering pressure line from vehicle.
Install or Connect

Power steering pressure line into vehicle.
Power steering gear line clamp at steering gear.
Steering gear heat shield and bolts.
Tighten
Bolts to 6 N.m (54 lb. in.) .
Lower vehicle.
Power steering pressure line at steering gear.
Use a 18 mm crow 5 foot line wrench with a 2 foot, 3/8 inch drive extension.
Power steering pressure line at pump.
Serpentine belt.
ECM cover.
Coolant recovery tank.
Fill system.
Bleed the system.
Inspect
For leaks.
To support the cradle while lowering it use a floor jack in the center of the rear.

yes, i would change both lines since you are there. no other disconnects.With the bolts removed it will drop about 4 to 5 inches. make sure the fronts are tight,take your time.

Mar 05, 2016 | Buick Cars & Trucks

1 Answer

Hi My Cadillac BLS 2.0T is losing power in gear 1,


You have a slipping clutch in the first epicycle gearing in the gearbox - it will have to be completely refurbished.

Oct 03, 2013 | Cars & Trucks

1 Answer

How to remove rack and pinion from 99 chrysler lhs


There are few help links showing exact accurate procedure to replace Rack and Pinion. Click the link below and follow the procedure:-----
Pinion Seal Replace on Dodge Dakota? http://howtobyme.blogspot.in/2012/04/pinion-seal-replace-on-dodge-dakota.html

-----------

How to Replace a Rear Pinion Seal.
http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-rear-pinion-seal.html
------------

How to replace Power steering rack and pinion gear on Chevy Silverado 2500 HD? http://technoanswers.blogspot.in/2012/02/how-to-replace-power-steering-rack-and.html

----------
How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html

-----------
How to replace power rack and pinion steering gear on Toyota cruiser? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-power-rack-and-pinion.html

----------


How to replace Power Rack and Pinion Steering Gear on Acura Car Models? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-power-rack-and-pinion.html


------------
Front Drive Pinion Seal Removal on Ford Explorer? http://repairhelpcenter.blogspot.in/2012/03/front-drive-pinion-seal-removal-on-ford.html

-------------
How to Replace Driveshaft, Pinion Flange & Seal?

http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-driveshaft-pinion-flange.html

------------


How to Replace Power Rack & Pinion Steering Gear On 2007 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


----------
How to Remove Power Rack & Pinion Steering Gear on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-remove-power-rack-pinion.html

-----------

Power Rack & Pinion Steering Gear replacing details for Buick Park Avenue and Pontiac Bonneville

http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

-------------


How to Replace Power Rack & Pinion Steering Gear on Mercedes Benz Truck? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html


---------
How to replace Power Rack & Pinion Steering Gear on Toyota 4Runner? http://howtobyme.blogspot.in/2012/03/how-to-replace-power-rack-pinion_27.html

-----------

Power Rack & Pinion Steering Gear Replacing on Toyota Land Cruiser & Sequoia? http://schematicsdiagram.blogspot.in/2012/03/power-rack-pinion-steering-gear.html

----------
Power Rack & Pinion Steering Gear Removal on Toyota RAV4? http://repairhelpcenter.blogspot.in/2012/03/power-rack-pinion-steering-gear-removal.html

----------
How to Replace Power Rack & Pinion Steering Gear on Toyota Sienna? http://technoanswers.blogspot.in/2012/03/how-to-replace-power-rack-pinion.html

------------
These details will help.
Thanks.



Nov 23, 2012 | Cars & Trucks

2 Answers

I have 1995 Nissan Terrano 4x4.Thishas an Automatic trans. It will not change gear.I have a power/hold button next to the hand brake.The power light flashes


If the power hold button switch On,It will stop the gear shifting & hold the gear position. or the problem with the system.

Feb 08, 2011 | Nissan Terrano Cars & Trucks

1 Answer

How to replace a steering rack? do i really have to loosen the bolts to the engine cradle to gain access?


Power Steering Gear Replacement
Removal Procedure


  1. Raise the vehicle on a hoist.
  2. Remove the tires and wheels.
  3. Remove the stabilizer shaft links from the control arms.
  4. Remove the tie rod ends from the steering knuckle.

5. Remove the intermediate shaft lower pinch bolt from the power steering gear.

  1. Remove the stabilizer shaft.

7. Remove the power steering hoses from the from the power steering gear.

8. Remove the power steering gear bolts from the frame.

  1. Remove the power steering gear through the left wheel opening.

Feb 06, 2011 | 2001 Chevrolet Malibu

1 Answer

Hello was wondering if you had instructions on how to replace the steering gear box on a 2001 chevrolet s10?


Removal Procedure

Notice: Do not rotate steering shaft after steering column has been removed. Damage to SIR components may occur.

Lock the steering column through the access hole in the steering column lower trim cover using the J 42640.
Remove the air cleaner assembly. Refer to Air Cleaner Outlet Resonator Replacement in Powertrain Management.Remove the intermediate shaft shield from the steering gear.Place a drain pan below the steering gear. Remove the pressure and the return hoses from the power steering gear. Cap or tape the ends of the hoses and the gear fittings in order to prevent dirt from entering the system.Remove the lower intermediate shaft coupling bolt. Draw alignment marks on the lower intermediate shaft coupling and the steering shaft. Remove the lower intermediate shaft coupling from the steering shaft. Remove the pitman arm. Refer to Pitman Arm Replacement.Remove the steering gear mounting bolts and the washers from the frame. Remove the steering gear.
Installation Procedure


Install the steering gear. Notice: Refer to Fastener Notice in Service Precautions. Install the power steering gear to the frame washers and the mounting bolts. Tighten Tighten the power steering gear to frame mounting bolts to 75 Nm (55 ft. lbs.). Install the pitman arm. Refer to Pitman Arm Replacement.Install the lower intermediate shaft to the power steering gear. Ensure that the alignment marks line up. Install the lower intermediate shaft coupling bolt. Tighten Tighten the lower intermediate shaft coupling bolt to 35 Nm (26 ft. lbs.). Install the pressure and the return hoses to the power steering gear. TightenTighten the pressure hose to 25 Nm (18 ft. lbs.) for the vehicle equipped with the 2.2L engines. Tighten the pressure hose to 30 Nm (22 ft. lbs.) for the vehicle equipped with the 4.3L engines. Tighten the return hose to 25 Nm (18 ft. lbs.). Install the intermediate shaft shield to the power steering gear. Install the air cleaner assembly. Refer to Air Cleaner Outlet Resonator Replacement in Powertrain Management. Unlock the steering column by removing the J 42640 from the steering column lower steering column trim cover access hole. Bleed the power steering system. Refer to Bleeding Power Steering System in Steering / Service and Repair.

Jul 23, 2010 | 2001 Chevrolet S-10

1 Answer

Very poor acceleration through all gears


diesel pump might not be working right. Try and check fuel pressure. I dont know if its turbo but if the turbo is failing then you will loose power

Feb 05, 2010 | 2006 BMW 5 Series

1 Answer

Need an digram of 2000 ford focus power steering pump


cfef959.gif
Item Part Number Description 1 - Steering wheel 2 - Steering column 3 - Boot 4 - Tie-rod 5 - Tie-rod end 6 - Steering gear 7 - Steering gear to fluid cooler hose 8 - Fluid cooler 9 - Power steering pressure (PSP) switch 10 - Power steering pump 11 - Fluid supply hose 12 - Fluid reservoir 13 - Pump to steering gear pressure line 14 - Steering gear pinion extension

Jul 30, 2009 | 2000 Ford Focus

1 Answer

How to change the power steering on 96 ford explorer


Section 11-02C: Steering Gear, Power Rack and Pinion, Explorer 1996 Explorer with Power Rack and Pinion Steering Workshop Manual REMOVAL AND INSTALLATION Steering Gear SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Pitman Arm Puller T64P-3590-F
Removal
  1. Start engine.
  1. Rotate steering wheel from lock-to-lock (entire gear travel). Record n umber of rotations.
  1. Divide the number of rotations by two. This gives the required number of turns to place system in the on-center position.
  1. NOTE: Verify the front wheels and steering wheel are in the straight-ahead position.

    From the lock position, rotate steering wheel the number of turns determined in Step 3. This places the gear in the on-center position.


    Steering Gear, Explorer




  1. NOTE: Do not rotate steering column when intermediate shaft is disconnected or DAMAGE TO CLOCKSPRING will result.

    Remove bolt retaining the lower steering column shaft to the steering gear input shaft.




  1. Disconnect the lower steering column shaft from the steering gear.
  1. Remove stabilizer bar attachment from frame for clearance to remove gear.
  1. Unscrew the quick connect fittings for the power steering pressure hose (3A719) and power steering return hoses (3A713) at the steering gear housing (3548).


    Power Steering Hose Connections





    Item Part Number Description 1 3A674 Power Steering Pump 2 3A719 Power Steering Pressure Hose 3 3F780 Power Steering Cooler and Hose Assembly 4 3504 Steering Gear 5 5005 Frame
  1. Plug ends of fluid lines removed and ports in gear to prevent damage and entry of dirt.
  1. Remove two (2) nuts from P/S cooler.
  1. Remove P/S cooler from vehicle.
  1. Remove and discard the cotter pin retaining the nut to tie rod end (3A130) and remove nut.
  1. Separate tie rod ends from front wheel spindle (3105) using Pitman Arm Puller T64P-3590-F.




  1. Remove the two nuts, bolts, and washer assemblies retaining steering gear (3504) to front crossmember (5019).
  1. Remove steering gear from vehicle. If required, remove steering gear mounting bracket housing insulators (3F640) and steering gear insulators (3C716) from steering gear housing.





    Item Part Number Description 1 N807881-S60 Bolt 2 385935-S36 Washer 3 3F640 Steering Gear Mounting Housing Insulator 4 3504 Steering Gear 5 N800255-S60 Nut 6 5019 Front Crossmember 7 3C716 Steering Gear Insulator
Installation
  1. If removed, install steering gear mounting insulators into the steering gear housing.
  1. Push the steering gear mounting insulator and steering gear insulator in until there is no space between the lip on the insulator and steering gear housing.
  1. Position steering gear on front crossmember. Install nuts, bolts and washers retaining steering gear to front crossmember. Tighten to 128-172 Nm (94-127 lb-ft).
  1. Position power steering cooler onto bolts and install nuts. Tighten nuts to 68-92 Nm (50-68 lb-ft).
  1. NOTE: The fittings design allows the power steering pressure hose and power steering return hose to swivel when properly tightened. Do not attempt to eliminate looseness by overtightening, since this can cause damage to fittings.

    Connect power steering pressure hose and power steering return hose to appropriate ports on steering gear housing. Tighten fittings to 27-34 Nm (20-25 lb-ft).
  1. NOTE: Make sure the tie rod ends (3A131) are seated in the tapered spindle holes to prevent rotation while tightening nut.

    With the steering gear, steering wheel (3600) and wheel (1007) in the on-center position, attach the tie rod end to front wheel spindle and tighten to 56-76 Nm (77-103 lb-ft).
  1. If necessary, advance tie rod nuts to the next slot. Install cotter pins.
  1. NOTE: Verify that no rotation from the on-center position has occurred.

    Position steering column lower intermediate shaft over steering gear input shaft. Outer input shaft dust shield must be in place. Replace pinch bolt and tighten to 41-56 Nm (30-42 lb-ft).
  1. Replace the front wheel and tire assemblies. Refer to Section 04-04 .
  1. Replace wheel covers.
  1. Lower vehicle.
  1. Refill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F.
  1. Purge air from steering system. Refer to Section 11-00 . Verify absence of any unusual power steering noise.
  1. Check and adjust toe alignment specifications. Refer to Section 04-00 .
  1. Make sure steering gear operates correctly and is not leaking.
  1. Check and adjust fluid level in power steering oil reservoir.

Jul 10, 2009 | 1998 Mercury Villager

1 Answer

How do i change inner tie rod , do i need a special tool.


i think steering gear has to be removed to get rubber bellows off to access tie rod.

486d579.gif Section 11-02: Steering System, Power 1997 Continental Workshop Manual
DISASSEMBLY AND ASSEMBLY Tie Rod and Bellows SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Bench Mounted Holding Fixture T57L-500-B
Disassembly
  1. NOTE: Drill out mounting holes in holding fixture with a 9/16 inch drill to allow the power rack and pinion steering gear assembly mounting bolts to fit.

    Mount power rack and pinion steering gear assembly in Bench Mounted Holding Fixture T57L-500-B.
  1. Remove tie rod ends (3A130).
  1. sve~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care not to damage bellows. If bellows are damaged, this will allow contamination into the steering gear and cause leakage.
    Remove four clamps retaining bellows to steering gear housing (3548) and front wheel spindle tie rods (3280). Discard clamps if damaged or excessively corroded.
  1. NOTE: Steering gear does not use rivets or roll pins between the inner front wheel spindle tie rod and rack.

    Remove bellows along with power steering gear rack tube (3K762).
  1. Position power rack and pinion steering gear so that several steering gear teeth are exposed. Hold steering gear sector shaft (3575) with an adjustable wrench on end teeth only while loosening ball joint nuts.
Assembly
  1. Expose several steering gear teeth and hold steering gear with adjustable wrench.
  1. Tighten each front wheel spindle tie rod separately to 90-110 Nm (67-81 lb-ft).
  1. Thoroughly clean steering gear and steering gear housing bore of any foreign material. Any abrasive material is extremely harmful to high-pressure oil seals.
  1. Apply Steering Gear Grease C3AZ-19578-A or equivalent meeting Ford specification ESW-M1C87-A to groove in front wheel spindle tie rod where tie rod bellows clamp to front wheel spindle tie rod and uniformly to inner diameter of tie rod bellows before installation. This allows for toe-in adjustment without twisting tie rod bellows.
  1. Install tie rod bellows and power steering gear rack tube. Make sure power steering gear rack tube is positioned as shown.


    Power Steering Gear Rack Tube and Tie Rod Bellows Installation

Apr 04, 2009 | 1997 Lincoln Continental

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...