Question about 2000 Mercury Cougar

Open Question

Where is the vent valve located on 2000 cougar 2.5L

Where is the canister vent valve solinoid located on 2000 cougar 2.5L

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How much is it normally to repair the evap on my 2000 Chevrolet Malibu


Caprice sorry to tell you this but the whole system is a problem .

If the fuel lines arn't rusting out the gas tank is or the fuel pump is on the way out .

I will try to explain the system to you or at least how they say it should work.

It might be better if you told me what code you got or told you got I now a lot about this system I have one and have made it work in spit of the disgin

Mar 08, 2015 | 2000 Chevrolet Malibu

1 Answer

Where is the evap canister solinoid located at honda accord 2000


2000
why not post the DTC error for better answers/?
and country.?
now my answer from USA, cars.
1: in usa open hood, see vacuum sticker, its there.
2: in FSM there are 3, purge control and bypass VSV. and vent shut off VSV.
so which one. ill answer for all 3.
at the canister. (im looking ,in alldata.com so an you)
1: CAN , hose.
one goes to tank, directly not that hose.
2: hose 2. is vent shut valve top of CAN, and goes to Vent can filter.
3: hose 3: to purge joint then purge valve.
4: and last host to bypass valve. this valve has 3 hoses (unique)

alldata.com click evap emmissions tab.

Oct 25, 2013 | 1998 Honda Accord

1 Answer

I have a es300 with a 0446 code and I am told I need a vacuum switch. Where is the vaccum switch located? I have ordered the part (without the canister) and I hope I can figure out which switch it is. ...


There is a chance the problem is something other than the switch you have ordered.
Below is the explanation for the code. You may have a leak somewhere in the EVAP system.

The Evaporative System (EVAP) canister vent control valve is located on the EVAP canister and is used to seal the canister vent.

This solenoid valve responds to signals from the Engine Control Module (ECM). When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components. This solenoid valve is used only for diagnosis, and usually remains opened.
Read more: http://engine-codes.com/p0446_lexus.html#ixzz21VFZi1D9

Jul 23, 2012 | 2000 Lexus ES 300

1 Answer

Vent vlav solenoid pontiac gran am gt


The solenoid for the purge vent valve is located near the vapor recovery carbon canister, a diagram of the location of the carbon canister is located under the hood on the emission sticker.

May 17, 2012 | 2000 GMC Jimmy

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

2 Answers

I HAVEA 2006 CHEVERLET SUBURBAN 1500, AND THE CHECK ENGINR LIGHT STEAYS ON. THE CODE IS P0449; WHAT IS THIS AND WHERE IS IT LOCATED AT.


Hello. Your code indicates that your emission system is acting up. If you live in California, you might have a problem passing the next mandatory emmissions test. The PCM has determined that a malfunction exists in the electrical circuit for the vent valve/solenoid in the evaporative emission control system.

Definition:
EVAP (Evaporative Emission System) purge/vent solenoid circuit condition

Explanation:
The solenoids and system wiring are monitored for opens or shorts

Probable Causes
1- Purge or vent solenoids defective
2- Check connector and wiring
3- fuel, saturated vapor canister
4- Failed EVAP vent solenoid

Apr 08, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

P1451 Code on Mercury Cougar. How do I fix it


Here is the information that you need:

NOTE
Enter this Pinpoint Test only when directed here.

The use of a soap solution, such as SNOOP, around the fuel filler cap or the use of the hydrocarbon emission analyzer to determine an evaporative emission system leak is not recommended. The mandatory Rotunda Evaporative Emission System Leak Tester for OBD II (including the ultra-sonic tester) is the only device to be used at this time for evaporative emission system leak detection.

This Pinpoint Test is intended to diagnose the following:
Evaporative Emission (EVAP) Monitor System

e365c10.gif

Sep 26, 2009 | 2000 Mercury Cougar

Not finding what you are looking for?
2000 Mercury Cougar Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

fordexpert

Level 3 Expert

5495 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...