Question about Chevrolet Cars & Trucks

Open Question

How do i change a evap vent solenoid - Chevrolet Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

  • 37 Answers

SOURCE: HAVE A TROUBLESHOOTING MESSAGE PO446

DTC P0446 Evaporative Emission (EVAP) Vent System Performance

The vehicle control module (VCM) monitors the performance of the evaporative emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this diagnostic trouble code (DTC) if the vacuum decay rate is more than a predetermined value. The VCM monitors the amount of vacuum and the amount of pressure in the EVAP system by monitoring the fuel tank pressure sensor. For this DTC, the VCM turns ON both the EVAP purge valve and the EVAP vent valve when the Conditions for Running the DTC are met. This applies an engine vacuum to a closed EVAP system. The VCM turns OFF both the EVAP purge valve and the EVAP vent valve when the system reaches a correct amount of vacuum. The EVAP system should quickly RELEASE the vacuum in the EVAP system with the EVAP purge valve OFF and the EVAP vent valve OFF (open). This test indicates a blocked or restricted EVAP vent path if the EVAP system fails to release the vacuum quickly enough.

3208f98.gif


Posted on Dec 06, 2008

MNfisherman
  • 11896 Answers

SOURCE: replacing the evap canister

It is the big black box on driver side front next to fender. It has to vacuum hoses going to it.

Posted on Jul 10, 2009

  • 7 Answers

SOURCE: Bad Evap Vent Solenoid

On the passenger side of the car there it a canister next to the gas tank (right infront of the rear wheel) it's right there. You don't need to pull the wheels to access it.

Posted on Jun 14, 2010

  • 14036 Answers

SOURCE: How to replace the evap vent solenoid on a 2001

LOOK ON THE INTAKE MANIFOLD.THATS WHERE IT IS.

Posted on Jul 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I changed everything on a 2007 chevy uplander the camshaft position sensor And the purged sensor And the throttle body and It cam up a new code p0449


DTC P0449: Evaporative Emission (EVAP) Vent Solenoid Control Circuit , your vent solenoid is opened or the wiring circuit is . The vent solenoid is by the charcoal canister at the gas tank .
P0449 Battery voltage is supplied to the EVAP canister vent solenoid valve. The control module grounds the EVAP canister vent solenoid valve control circuit to close the valve by means of an internal switch called a driver. The scan tool displays the commanded state of the EVAP canister vent solenoid valve as ON or OFF. The control module monitors the status of the driver.

May 03, 2016 | Cars & Trucks

1 Answer

Code po449 evap solenoid


What about it ? What would you like to know ? Where is it , what is it ? What engine does yours have , six different possibilities .
DTC P0449: Evaporative Emission (EVAP) Vent Solenoid Control Circuit.
Battery voltage is supplied to the EVAP canister solenoid valve. The ECM grounds the EVAP canister vent solenoid valve control circuit through an internal switch called a driver. The ECM monitors the status of the driver. A scan tool will display the commanded state of the EVAP canister vent solenoid valve as ON or OFF. P0449 Vent Valve Testing EVAP Systems

Mar 10, 2016 | 2008 Chevrolet Trailblazer

1 Answer

2007. What are the probable causes of DTC P0446?


DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.


?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.


?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .


?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system


Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

    Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
    If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

  1. Install the fuel cap.
  2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.
?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.



If

Sep 06, 2015 | Chevrolet Impala Cars & Trucks

1 Answer

Hi my evap vent selenoid is un top of the gas tank can i change it place and put it far away from the evap canister thank you...


If the vent is separate from the solenoid yes you can move it. I use heater hose to go between the solenoid and the vent. Just try and mount it somewhere the dust and dirt wont get to it.

Apr 24, 2015 | 2007 Chevrolet Uplander

1 Answer

Where is my vent valve solenoid on my 2006 Chevy Colbalt?


It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

Feb 25, 2015 | Chevrolet Chevy Cars & Trucks

1 Answer

Code p0449 vent solenoid intermittent


EOBD II Error Code: P0449
Fault:
Evaporative Emission (EVAP) System, Vent Valve - Circuit Malfunction
Possible Cause:
Wiring harness.
Evaporative emission (EVAP) canister purge valve.
Engine control module (ECM).

Dec 28, 2013 | 2001 Pontiac Montana

1 Answer

Codes 446 and 452


P0446 has nothing to do with the canistor !
DTC P0446 Evaporative Emission (EVAP) Vent System Performance
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inches H2O in a calibrated time, this DTC sets.
DTC P0452 Fuel Tank Pressure (FTP) Sensor Circuit Low Voltage


How to troubleshoot an EVAP Pressure Sensor problem P0452 GM

EVAP Vent Solenoid Code P0446 The solenoid is stuck open !

Apr 23, 2017 | 2005 Chevrolet Silverado 1500HD

1 Answer

Solution for 1999 chevy cavalier code p0440


There has been a service bulletin isued for that code. I have run into this before, also the wires comming out of the connector. That would bethe first thing to check. Here is what the bulletin states. Emissions - SES Lamp ON/DTC P0440 (EVAP) SetNotesFile In Section: 06 - Engine/Propulsion SystemBulletin No.: 02-06-04-044Date: August, 2002TECHNICALSubject: Service Engine Soon (SES) Light Illuminated, DTC P0440 Set (Replace Fuel Tank Evaporative Emissions Control System (EVAP) Vent Solenoid Harness) Models: 2000-2002 Chevrolet Cavalier2000-2002 Pontiac Sunfire ConditionSome customers may comment that the SES light is/was illuminated.A technician may find DTC P0440 is stored in the PCM.CauseThe EVAP solenoid harness may be misrouted around the rear antilock brake (ABS) wire harness causing a chaff/damage to the EVAP vent solenoid harness, setting DTC P0440.CorrectionFollow the service procedure below to diagnose and correct this condition.1. Install a Tech 2 scan tool and select the appropriate vehicle. Verify that a DTC P0440 is stored in the PCM. 2. Raise the vehicle on a hoist. Refer to Lifting and Jacking the Vehicle in General Information (SI Document ID # XXXXX).

4_9_2012_3_31_41_pm.gif

Locate and inspect the EVAP vent solenoid harness (3) routing. The harness may be routed below the ABS wiring harness (4) at the right rear corner of the fuel tank, causing stress on the EVAP solenoid harness (3).



4_9_2012_3_32_10_pm.gif

4.Disconnect the EVAP vent solenoid harness (3) from the EVAP vent solenoid (2) and connector C313 (1). Discard the EVAP vent solenoid harness (3).


5.Connect the new EVAP vent solenoid harness (3), P/N 22687059, to the EVAP vent solenoid (2), route the harness above the rear ABS harness (4) and connect the EVAP vent solenoid harness (3) to connector C313 (1).


6.Lower the vehicle.


7.Clear the DTC's with the Tech 2 scan tool.



If all of the wires are good you will want to check for any leaks in the evap system.



Hope helps.

Apr 09, 2012 | 1999 Chevrolet Cavalier

1 Answer

Engine light is on. a diagnostic suggested a possible defective vent solenoid...where is this part located?


First try the gas cap to make sure it is on secure and tight.

Code P0440 indicates a problem with the EVAP vent solenoid, which essentially controls the venting of your gas tank in order to maintain a consistent pressure in the tank. This solenoid is mounted on the back of the chassis cross-member just behind your gas tank.

However, a loose or leaking vent hose that connects to this solenoid can also cause this code to appear.

Code P0446 indicates that the VCM (Vehicle Control Module) received
a failure when it tested the EVAP vent solenoid.
The VCM monitors the performance of the Evaporative Emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this code if the vacuum decay rate is more than a predetermined value.

Again, this could indicate a loose or leaking vent tube.
This solenoid is very easy to test simply by first checking for continuity across the coil, if that's good then applying 12 volts across the two pins on it will cause it to "click" changing the position of the valve.

Mar 22, 2011 | Chevrolet Cavalier Cars & Trucks

2 Answers

Where is the evaporative fuel solenoid on a 1998 sw2 saturn? i have 2 monitors that with not reset on is the solenoid and the other evap system. i have already changed the gas cap. i do not have a service...


Evaporative Emission (EVAP) Canister Purge Soleno Evaporative Emission (EVAP) Canister Purge Solenoid Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.
id Valve is on top of the fuel tank.

Evaporative Emission (EVAP) Canister Vent Solenoid Valve is at the upper end of the fuel filler pipe.

Oct 07, 2009 | 1998 Saturn SC

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...