Question about 2001 Chrysler 300M

1 Answer

Where is the air intake valve gasket located in 2001 300m

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 373 Answers

Locate your air filter [Im assuming it is a 5.7L] follow plastic tubes to the back of the motor. Where the tubes bolt onto the motor is where the gasket will be. As the car is running and idling high spray the brake cleaner or ether all around that area, no worries about soaking anything as the stuff evaporates immediately. Use the straw provided if need be to get a good aim, and do it back and forth to see if there is a change in idle. I looked up your motor on google and it shows the gasket at the rear of motor by the firewall just like I figured it would be. Spray a good douse all around making sure it goes all around where the gasket will be. The gasket is metal so it is important to spray the full length of said gasket. Let me kn ow how you make out. If this fails to give an indication or idle stays the same, try spraying the spray onto the air filter and see if the idle goes down, but that is a test of last resort

Posted on Apr 12, 2014

Testimonial: "Jamie is a champ!! Instructions were easy to follow !!"

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace a intake plenum gasket


Well basically, you remove the intake plenum and replace the gasket and reinstall the plenum. Here are the steps:

1. Disconnect the negative battery cable from the remote jumper terminal located at the right strut tower.
2. Remove the air inlet resonator and tube.
3. Remove the throttle actuator cables from the throttle arm and bracket.
4. Disconnect Secondary Runner Valve (SRV), Manifold Tuning Valve (MTV), Throttle Position Sensor (TPS), Idle Air Control (IAC) motor electrical connectors.
5. Remove the electrical connector and the Intake Air Temperature/Manifold Absolute Pressure (TMAP) sensor.
6. Disconnect vacuum hoses from the Secondary Runner Valve (SRV) reservoir, Speed Control reservoir, and PCV.
7. Remove right and left intake manifold supports.
8. Remove support brackets at the intake manifold front corners and MTV.
9. Loosen upper fastener attaching throttle body to support bracket.
10. Remove clips attaching EGR tubes to intake manifold.
11. Remove intake manifold bolts and manifold
12. Remove old gaskets, Clean gasket surfaces, and install new gaskets.
13. Reverse steps to reinstall manifold

Jun 16, 2012 | 1999 Chrysler 300M

Tip

How to remove/replace the Valve Cover Gaskets on a New Beetle car?


Replace the valve cover gasket if the valve cover gaskets are leaking or if they're worn. The procedure is as follows:--
1) First of all let the motor cool down if the car was recently driven. Then remove the air intake boot.The air intake boot ios attached to the engine's throttle body.
2) Carefully disconnect the throttle cable , hoses and electrical connectors located on the upper intake manifold.
3) Then disconnect the hard pipe that is connected to the EGR (exhaust gas recirculation) valve.
4) The EGR valve is located beneath the upper intake manifold.
5) Then remove the bolts from both the upper intake manifold and the manifold support bracket.
6) Now the upper intake main fold and lower intake manifold both have got loose as you removed the nut.
7) After that remove the upper intake manifold from the lower intake manifold. Carefully place clean rags over the intake runners to prevent anything from falling into the intake system.
8) Then you will have to disconnect the crank case breather valve on the valve cover.
9) Then remove the bolts from the valve cover and remove the reinforcing straps.
10) Then remove the camshaft belt cover and the dust shield from the back of the camshaft sprocket.
11) Now carefully remove the valve cover. Properly clean the old gasket material with gasket remover.
12) You can install a new gasket in the reverse procedure of removal.


This will help. good luck.

on Mar 09, 2010 | Volkswagen Beetle Cars & Trucks

2 Answers

Hi, my 2002 malibu hesitate and whistle when I accelerate. It only works fine under 20mph, but when it exceed, it whistles and hesitate on accelerating. On highway, it barely goes up to 60mph and when...


Whistle noise indicates a major vacuum leak. Maybe something loose in the intake system. Maybe a vacuum hose disconnected. Will explain lose of power also.

Jun 24, 2011 | 2002 Chevrolet Malibu

1 Answer

Dear Sir: I have a 1997 Series III Sentra, with B14 engine. Lately, I have experienced that engine oil is accumulating in almost 4 spark plug wells, leaving the valve cover wet with oil and practically in...


sounds like you have a leaking valve cover gasket.
Have the sealing surface checked for damage and warpage and if all is well, replace the gasket.
You may also have a emmision system issue where the one way valve in the engine fume recirculating sytem is blocked allowing pressure to build up in the valve cover. This valve is usually located in the pipe which leads from the valve cover to the intake system. Remove the valve and clean it with kerosene. It should rattle when you shake it and you should only be able to blow air through it in one direction. when replacing it, make sure that air can flow from the valve cover to the air intake only, not the other way.

Mar 10, 2011 | Nissan Sentra Cars & Trucks

1 Answer

Picture of egr valve and were it is located


dffc43b.jpg

Fig. 11: EGR valve and component mounting-3.0L engine


da251ab.jpg

Fig. 12: EGR valve and component mounting-3.8L engine

Removal:
  1. Disconnect the negative battery cable.
  2. If necessary, remove the air inlet tube from the throttle body and air cleaner housing.
  3. Label and detach all vacuum hoses from the EGR valve.
  4. Label and detach any electrical wiring harness connectors from the EGR valve.
  5. Disconnect the EGR valve-to-exhaust manifold tube from the EGR valve.
  6. Remove the EGR valve mounting fasteners, then separate the valve from the upper intake manifold.
  7. Remove and discard the old EGR valve gasket, and clean the gasket mating surfaces on the valve and the intake manifold.
To install:
  1. Install the EGR valve, along with a new gasket, on the upper intake manifold, then install and tighten the mounting bolts to 15-22 ft. lbs. (20-30 Nm) on 3.8L engines, or to 106-159 inch lbs. (12-18 Nm) on 5.0L engines.
  2. Connect the EGR valve-to-exhaust manifold tube to the valve, then tighten the tube nut to 30 ft. lbs. (41 Nm).
  3. Connect all wiring or hoses to the EGR valve.
  4. Install the air inlet tube.
  5. Connect the negative battery cable.

Hope this helps (remember comment and rated this).

Jul 27, 2010 | 1995 Ford Windstar

1 Answer

How to remove a idle air control valve is windstar 2001


Idle Air Control Valve The Idle Air Control (IAC) valve is located on the air intake plenum.


7515536.gif

Removal & Installation
Disconnect the battery ground cable.
Disconnect the Idle Air Control (IAC) electrical connector.
Remove the bolts and the IAC valve.
Discard the gasket.
To install:
Install a new gasket and position the IAC valve.
Torque the retaining bolts to 8 ft. lbs. (11 Nm).
Attach the electrical connector.
Reconnect the battery ground cable.

May 23, 2010 | 2001 Ford Windstar

1 Answer

Changing pvc valve


1995 Geo Truck Tracker 4WD 1.6L TBI SOHC 4cyl
The PCV Valve is located under hood, center, upper engine area, top of engine, mounted in passenger side of intake manifold.

The low gas mileage and the versatility that your 1995 through 1999 Geo Tracker offers are two benefits of owning it. The maintenance needs to be kept up on your Geo Tracker. One form of this maintenance is to replace the valve cover gasket once you have driven 100,000 miles or more.
  1. Allow your engine to cool. Disconnect the negative battery cable. Remove the air inlet hose and air intake case or air cleaner housing. Detach the PCV valve hose from the PCV valve. Separate and remove the spark plug wires and the accelerator cable from their clips.
  2. Loosen and remove the valve cover bolts. Lift the cover up and off. Using a flathead screwdriver, gently nudge the gasket out of the gasket seating area. Using automotive engine cleaner and a clean cloth rag, clean the gasket seating area.
  3. Place the new gasket in the gasket seating area. Put the cover back into place. Put the bolts in and then using a torque wrench tighten them. Do not over tighten the bolts or the gasket will not fit correctly. Reconnect the spark plug wires and the accelerator cable in the holding clips.
  4. Reconnect the rubber hose to the PCV valve. Install the air intake case, or air cleaner housing, and the air inlet hose. Reconnect the negative battery cable. Add oil to the car and start the engine. Allow the car to run 10 to 15 minutes. This will allow the oil to lubricate the engine while it moves to the top.
I hope helps with this (remember rated this help) Good luck.

Dec 29, 2009 | 1995 Geo Tracker

3 Answers

EGR problem on 2001 Camry??


Replace filter in EGR Modulator located to the left of EGR valve.
How do you clean the intake port below the EGR valve?

Sep 30, 2009 | 2001 Toyota Camry Solara

1 Answer

My 96 altima has a rough idle problem.


Sounds like you could have a vacuum leak in the intake manifold due to a faulty gasket, spray the gasket down with parts cleaner, csee if the idle smoothes out if it does you have a bad manifold gasket.

Sep 28, 2009 | 1996 Nissan Altima

1 Answer

EGR VALVE 1999 MERCURY COUGER


SECTION 303-08: Engine Emission Control 1999 Cougar Workshop Manual REMOVAL AND INSTALLATION Exhaust Gas Recirculation (EGR) Valve Removal
  1. Remove the air cleaner outlet tube.
    1. Disconnect the intake air bypass hose.
    1. Disconnect the positive crankcase ventilation hoses.
    1. Remove the air cleaner outlet tube.
  1. Disconnect the tube from the exhaust gas recirculation valve.
  1. Remove the exhaust gas recirculation valve.
    • Disconnect the vacuum hose.
Installation
  1. sxu~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: When cleaning the gasket faces, do not allow debris to enter the intake manifold or exhaust gas recirculation valve.
    Clean the gasket faces of the intake manifold and exhaust gas recirculation valve.
  1. Install a new exhaust gas recirculation valve gasket.
  1. Position the EGR valve and install the bolts.
    • Install the vacuum hose.
  1. Connect the EGR tube.
  1. Install the idle air control valve. For additional information, refer to Section 303-14A . For additional information, refer to Section 303-14B .

Sep 15, 2009 | 1999 Mercury Cougar

Not finding what you are looking for?
2001 Chrysler 300M Logo

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...