Question about Jeep Commander

Open Question

Transmission would go into gear but car would not go over 20 mph on 2007 jeep commander

Will low oil level cause this issue with the transmission. not sure if there is a sensor connecting the two or not

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 65 Answers

SOURCE: how to check trans oil level

I assume that you have a 6 cyl.There are two plugs on the trans pan.the big one is the drain and the small one is the check plug.There is a fill on the side.The trans uses ws fluid which is what you need to use.What i do is remove the check plug and add fluid until it comes out.Then start the engine and let it warm up, the recomended temp is 97 to 115 degrees f or 36 to 46 degrees c.As it warms up the fluid will come out,once it reaches the temp range put the plug back in.I use a computer to monitor the temp but a temp gun on the pan will do.

Posted on Nov 28, 2008

  • 202 Answers

SOURCE: Reset my engine oil low in 2007 chevy impala

it will say in your owners manual but i believe you turn your ignition key to the run position not the start. and pump the gas pedal 3 times with in 5 seconds

Posted on Apr 14, 2009

Molson02536
  • 3854 Answers

SOURCE: Low oil pressure light goes on until car warms up. Oil level is good

The oil pressure sending unit has gone bad. I sending unit is just above the oil filter and you can get to it from the top. When you face the Engine look down towards the oil filter, the oil pressure sending unit is just above that and it looks like a cylinder with two wires coming from it. If you don't see it, it's right between the exhaust manifold and oil filter.
If you go to Auto Zone or Parts Source, they'll have the oil pressure sending unit and the step by step instructions, When installing the new sensor. Do not use teflon tape or any sealant, the sensor is tapered and need's the good ground from the engine to give you right readings.
Good luck and hope this helps.

Posted on May 11, 2009

  • 1 Answer

SOURCE: Issue after replacing the Transmission Range Sensor

I've talked to three different Suzuki Dealerships since mine just went out as well, and they have all told me that they have to reprogram the computer or it wouldn't be able to shift into the correct gear.

Posted on Sep 25, 2009

  • 62 Answers

SOURCE: 2005 hyundai sonata oil light flickers. oil

Yes there is a sensor located on the front of engine on the transmission side(single wire). It cannot be "reset". Possibly loose connection at the sensor,or a faulty sensor, OR... you could be losing oil pressure inside the engine somewhere(lets hope not) these engines are designed to run on very low oil pressure compared to cars of days gone by. The sonata 4 cylinder runs about only 12 psi. The V6 is 7.6 psi or more.
So if it is an oil pressure issue it is extremely important not to run the car before it is fixed or you will need an entire engine.

Posted on Jan 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHY DOES MY 2003 JEEP WRANGLER 4.2 ENGINE AUTOMATIC TRANSMISSION CUT OUT RIGHT BEFORE IT SHIFTS GEARS


cut?
what does it do.
flare or slip
fail to up or down shift correct
shift to wrong gear say 2 to 4, or 2 to 1.?
are you just cruising when this happens
or only accelerating.
or?
did you scan to the PCM for DTC errors yet?
check fluid levels.
is engine overheating,?

Jul 05, 2016 | 2003 Jeep Wrangler

1 Answer

Service electric brake system


Perhaps I'm stating the obvious, but have you checked for possible transmission/transfer case issues?

Nov 07, 2013 | 2005 Jeep Grand Cherokee

2 Answers

2006 Jeep Commander


check transmission fluid level could be low if vechicle has 60000 time for fluid filter change.if all is good have transmission shop do diagnostic check using scanner check transmission see whats causing light to flash on.

Jun 19, 2013 | Cars & Trucks

1 Answer

How many qts of oil do i need


Depends on your engine.

1980 JEEP CJ-7 2.5L 4-cyl Engine Code [B]
CAPACITIES
Engine, GM without filter..........2.4 quarts[1]
Wix Filter ........ 51040
Cooling System, Initial Fill..........8.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....25 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 4.2L 6-cyl Engine Code [C]
CAPACITIES
Engine, without filter..........5.0 quarts[1]
Wix Filter..... 51522
Cooling System, Initial Fill..........11.0 quarts
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A999, 32RH..........8.4 quarts
3 speed A904, 30RH..........7.0 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Oil Drain Plug.....30 ft-lbs
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

1980 JEEP CJ-7 5.0L 8-cyl Engine Code [H]
CAPACITIES

Engine, without filter..........4.0 quarts[1]
Wix Filter..... 51258
Cooling System, Initial Fill..........13.0 quarts
Automatic Transmission, A999, 32RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, A904, 30RH Initial Fill..........4.0 quarts[2]
Automatic Transmission, Total Fill
3 speed A904, 30RH..........7.0 quarts
3 speed A999, 32RH..........8.4 quarts
Manual Transmission, 4-SPD, SR-4..........3.0 pints
Manual Transmission, 4-SPD, T176..........3.6 pints
Differential, Front..........2.5 pints[3]
Differential, Rear..........4.9 pints
Transfer Case,..........4.0 pints

1. Add extra oil when replacing filter. After refill check oil level.
2. With engine automatic transmission operating temperature, shift through all gears.
Check fluid level in NEUTRAL and add fluid as needed.
3. 1984-1992 Models with command-Track, add 5 oz of 75W-90 GL-5 to shift motor housing opening.

TORQUES
Manual Transmission T176
Fill Plug.....15 ft-lbs
Drain Plug.....15 ft-lbs
Manual Transmission SR4
Fill Plug.....20 ft-lbs

Oilman

Feb 02, 2013 | 1984 Jeep CJ7

1 Answer

Accelerate and car will not shift into third gear. Have to turn car off and re-start then seems ok til it happens the next time...


It could mean this.
The first thing you should try is changing the transmission oil and filter to see if this helps resolve the issue.
Check your transmission oil level. If the level is too far from it's optimal level, then this can cause all sorts of issues.

Nov 18, 2012 | 2007 Dodge Charger Daytona R/T Sedan

1 Answer

Transmission will not shift into 3rd gear


no problems before the mud deal but problems after the mud deal means that the problems started in the mud
check for mud in connections , wires disconnected , harness problems, vacuum hose to actuator broken or missing
run the fault codes to help point to a problem area
the transmission is sealed so there will be no need to change the oil or filter--just clean and check everything that is mud affected

May 31, 2017 | 2001 Isuzu Rodeo

1 Answer

How to fix problem codes 730-733 laredo 2009


There is no one fix works for all on these code. Also you have left out the letter and one number of the code I assume these are P0730 and P0733, if so read on.

P0730 CHRYSLER - Incorrect Gear RatioPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Shift solenoids harness or connectors
- Transmission mechanical problems
- Transmission hydraulic control circuit

P0733 CHRYSLER - Gear Ratio Error In Third GearPossible causes- Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit

Jun 27, 2012 | Jeep Grand Cherokee Cars & Trucks

2 Answers

I have 2000 jaguar xk8. it have a cord p1722 how can i fix this problem


The P1722 Possible Cause is:
- Transmission oil level low
- Selector cable adjustment / installation incorrect
- Output speed sensor problem (Refer to P0721 Possible Causes)
- Transmission mechanical failure
Hope this helps.

May 23, 2011 | 1998 Jaguar XJ8L

1 Answer

My car , E60 2004 530D goes into "transm.failsafe " continuously. Ive reset it and then its fine for a day or 2. Thers oil under the car still ( light brown) when parked. I had the oil topped...


I do think this is a low oil condition and you need to get it addressed now.Low oil will damage the transmission very quickly.The factory trans oil in this car is a light brown and almost the color of motor oil.The oil in an automatic transmission is not just for lubrication, it is also the hydraulic and cooling medium.Low oil means low pressure which means slip which means damage.Have the car towed to a sevice facility.This transmission can cost 4 to 5 thousand to repair.Good luck!

Mar 28, 2011 | BMW 530 Cars & Trucks

1 Answer

My 1993 saturn sl automatic transmission shifts hard into gears


Issue with Relay Command..Due To low Oil Level ...Please check Oil Level on transmission May have To Flush Transmission Oil Change Filter and Re-ajust Relay Bank .... If you want to preserve your Transmission longer... Due To Over Sleping Band inside your Transmission Good Luck...

Oct 06, 2010 | 1993 Saturn SL2

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...