Question about 2002 Kia Sedona

1 Answer

Need a detailed schematic of cmps sensor - 2002 Kia Sedona

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 91 Answers

Many parts stores if they show a part replacement are more the willing to print this out for you... thus you buying from them.....

Posted on Apr 12, 2014

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 INTREPID WITH 2.7 ACTS LIKE IT HAS A REV LIMITER AT 2500 RPM.HAS NEW CKPS AND CMPS. HELP,,,,,,


It should not be hitting the flywheel. You need a professional to look into this problem with a full function scanner to watch the crank sensor signal in real time.

Feb 22, 2017 | Cars & Trucks

2 Answers

MAF sensor in a Kia sorento 2006?


please be advised, you might run into issues down the road for the enhancement, (with smog and long time performance), but to answer your question, there should a schematic to show you how to do it, or if not, download a schematic of the system from google maybe

Apr 29, 2014 | 2006 Kia Sorento

2 Answers

How to change cam sensor on jaguar x k 8 99


The CMPS sensor is at the end of bank 2 (L/H Drivers side), works off the inlet side so will be on the inside of the head, you cant miss it at the back, you will need to take off the fuel connector going onto the rail to remove it via a 8mm hex bolt, just slides out, if its a little tight that will be the O ring that seals it in, just give it a wiggle!

Apr 26, 2012 | 1999 Jaguar XK8

1 Answer

How do i replace the camshaft position sensor


On 2001-2005 vehicles the camshaft position sensor is mounted at the rear of the cylinder head. On 2006 vehicles, the camshaft position sensor is located on top of the engine, on the engine head cover.

Testing 2001-2003
  1. Connect the scan tool to the data link connector.
  2. Start the engine. Allow the engine to reach operating temperature.
  3. Monitor the CMPS signal. It should continuously fluctuate between 0-5 volts.
  4. If abnormality is found, replace the sensor.

Removal & Installation
  1. Disconnect the negative battery cable.
  2. Disconnect the connector from the sensor.
  3. Remove the bolt that retains the sensor.
  4. Remove the sensor.
To install:
  1. Installation is the reverse of the removal procedure.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Dec 22, 2011 | 2001 Kia Rio

1 Answer

I was driving down the road in my 2001 sonata, and it just died on me and can not get it started, all the fues are good in fues box, i founded out that it did not have spark. now would that be a coil...


Hi, it can be either of those or possibly a shorted condense or a bad crank sensor. First, I would check for battery voltage at the positive terminals of the coil when the key is on. If no voltage there, try disconnecting the condenser. If there is voltage, then check for AC voltage across the coil terminals while cranking the engine. If there is no AC voltage, the problem may be the crankshaft position sensor. The crankshaft position sensor is located next to the flywheel/torque converter. The computer is rarely the problem unless there was a short that caused undue current to flow.

jturcotte_2266.gif


Testing Crankshaft Position Sensor
2.4L Engine
  1. Disconnect the sensor electrical connector. Connect an ohmmeter.
  2. Measure the resistance between terminals 2 and 3, on the crankshaft position side of the connector. Specification should be 0.486-0.594 kohm at 68 degrees F.
  3. If measured value is not within specification, replace the sensor.

  1. Be sure that the CKPS and PCM connectors are connected.
  2. Engine ON and monitor the signal waveform of the sensor on the scan tool. Check whether the waveform is synchronized with the crankshaft position sensor or not.
  3. If the waveform signal is normal, substitute with a known good PCM and check for proper operation. If the problem is corrected replace the PCM.
  4. If the waveform signal is not normal, substitute with a known good CMPS sensor and check for proper operation. If the problem is corrected replace the CMPS.

2.5L Engines
  1. Disconnect the sensor electrical connector. Connect an ohmmeter.
  2. Measure the resistance between terminals 2 and 3, on the crankshaft position side of the connector. Specification should be 0.486-0.594 kohm at 68 degrees F.
  3. If measured value is not within specification, replace the sensor.

Sep 16, 2011 | 2001 Hyundai Sonata

1 Answer

Truck burns alot of fuel, hesitates all the time and high idle, just replaced timing gear and chain. dealer says maybe 1 tooth off on cam, replaced distributor w/cam sensor, crank position sensor, (no...


If you have that code the distributor isn't set right. I don't suppose you have access to a scanner? That is the only way to get it set right.

Jul 10, 2010 | 1997 GMC Sierra

2 Answers

After replacing a camshaft position sensor a p1390 shows up


Cam sensor fires the injectors so ignition control is not really what it does. The crankshaft sensor provides spark control, the Cam sensor provides injector pulse timing.
The actual code no it throws is much more use for us to diagnose...pls specify the Engine light code and I can be much more helpful.
Why did u change the cam sensor for an oil leak? that does not seem to be an appropriate repair.... anyhow more info=better help
:)

Jan 17, 2009 | 1999 Mitsubishi Eclipse

Not finding what you are looking for?
2002 Kia Sedona Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8211 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...