Question about 2009 Suzuki Jimny 1.3

Open Question

How to remove the seat

How to remover rear seat base

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove rear seat for recovering,of Mitzubishi 4 door 2005 sedan


If the seat base is fixed it is usually held down with two or three screws on the underside of the seat pad. It's the upright panel behind your heels when your sat on the seat. The screws are usually on the left, right and centre.
if the seats tilt for loading they will be bolted down through the floor with the seat base raised.
The rear panel removal depends on if the seat back drops to increase loading space.
If yes, lower the back seat and unscrew it from the floor panel under the seat.
If no, it will be bolted in place from inside the boot, (trunk), through the metal panel the seat back rests again.

Jan 12, 2018 | Seat Cars & Trucks

1 Answer

Favorite thing dropped into the seat belt cavity in the back seat of a 2006 Lexus LS430. Any good ideas? Through the trunk or how do we remove the back seat?


Pop the rear seat base out. Just push against the seat base bottom on the sides of front of seat bottom with your knee and pull up with your fingers. Seat base will come up no problem. Retrieve your "favorite" thing and put the base back in, hold it down with your hands while pushing it towards the rear with your knee and it will pop over the holding clips. Ya got your piece back and no harm done.

Jul 20, 2017 | Lexus Cars & Trucks

1 Answer

Remove rear seat bases


Remove bolt that holds seat down push back seat and should lift up

Nov 22, 2014 | Seat Cars & Trucks

1 Answer

How to Remove rear seat on ford telstar


rear seats are removable by lifting the catches at the rear base of the seats where they attach to the floor. There is one on each side, and you have to undo both catches at the same time from behind, and pivot the seat forward, then pull it back..and it will come out. Watch out though, as they seem to weigh a ton.
Other technical services, you can visit here

Sep 18, 2014 | Cars & Trucks

1 Answer

Remove rear seat


seat base just pulls up, rears pivot down to reveal bolt fixing points, side bolsters require seat belt lower bolt removal then pull out towards front of the car

Apr 15, 2014 | 1994 BMW 316i

1 Answer

Bentley arnage rear seat removal


Ease out and disconnect the spring loaded foot well lights. This exposes the small seat location bolts. Remove these and the seat base can be removed, exposing the upright fixings.

Apr 06, 2013 | Cars & Trucks

1 Answer

How to remove the rear seat


Rear seats are fastened in many different ways. On most cars, the base part of the seat is held in place by a metal snap going into a hole. To remove, pull on the front of the seat. Some cars have a metal or plastic tab that has to be pulled, pushed, or moved to the side, while pulling on the front of the seat. Other cars, mainly German, use bolts or screws in the front to hold the base of the seat. Many American car seats (GM) have a hook that fits into a metal brace. To remove the bottom part of the seat push hard towards the back and then up. Most Hondas use a bolt (10MM) on the back part of the seat between the bottom part of the seat and the back support (towards the middle) that has to be removed. Then the seat can be pulled up from the back. Before you pull on a seat, try to analyze what is holding it. Most seats do not need a lot of force to be removed, they all have a trick.
The back support on the rear seat is a bit more standard in the way it is fastened. At the top, there are 2, 3 or 4 pieces of metal that go into a hole. There are 2 or more bolts that hold the backrest at the bottom. Once you have removed the bottom part of the seat, take the screws or bolts out, and slide the back rest up and out. On a few cars you have to remove the rear deck and other side panels out first. If you can't figure it out, remove the panels in the other side of the backrest (trunk) and examine carefully how the seat is fastened.

Hope this helps, good luck!

Jul 27, 2010 | 2001 Kia Sephia

1 Answer

How to remove the 3rd seat on Yukon 2007


  • Open the rear lift gate on the Yukon. You need to have access to the seat controls to remove it from the vehicle.
  • Lift the release lever located near the bottom of the back side of the seat. Fold the seat-back forward and lay it flat.
  • Locate the carrying handle at the base of the seat in the rear. Grasp the handle and pull it toward the rear of the vehicle to release the seat from the floor latch.
  • Roll the seat backward along the track built into the floor of the vehicle. The track will guide the wheels so that you can roll the seat completely out of the rear of the vehicle
  • Jun 29, 2010 | 2007 GMC Yukon

    2 Answers

    On a 1989 nissan maxima with sonar suspension II how do you disassemble the strut assembly? the mounting bracket for sonar adapters is in the way of the strut center bolt.


    First you must remove the rear seat to gain access to the top strut mounts. The bottom of the rear seat comes out first. On the 91 model there are two tabs at the base of the seat bottm that you pull forward to release the seat bottom. I'm not sure if the 89 is the same. After removal of the rear seat bottom, you will see a bolt at the bottom of each side of the rear seat back that need to be removed. Fold down the arm rest and disconnect the vinyl cover at the base of the armrest to expose and remove two screws. Push up on the rear seat back to unhook three plastic hooks (center and one at each end) at the top of the rear seat back. Remove the seat back. Remove the large metal support panel that is behind the seat back. Safely jack up the rear of the car and support on jack stands so the rear wheels hang free. Doing one strut at a time, remove the two top strut mount bolts leaving the center strut stud nut in place. The strut and mount will lower out of the unibody. Disconnect the bottom strut mount. Remove the strut/coil spring assembly. Using a strut/spring compressor (some auto parts stores rent these) compress the spring. Carefully remove the top strut stud retaining nut, top strut mount, bumpers and strut boot. Carefully install compressed spring, strut boot, bumpers and top strut mount on new strut and install washer and retaining nut. Reinstall strut and etc. in reverse order.

    Sep 15, 2009 | 1989 Nissan Maxima

    1 Answer

    I need to replace the front driver's seat in a 95 saturn...


    seat frame base is held to floor with four bolts, one in each corner.  Begin by moving seat to the full forward position, remove the two rear seat frame bolts, they may be covered by carpet and plastic trim.  Them move seat to full rear position and remove both front frame bolts, the seat will now be free to remove.  Keep me posted

    Jan 06, 2009 | 1995 Saturn Sl

    Not finding what you are looking for?
    2009 Suzuki Jimny 1.3 Logo

    Related Topics:

    12 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Suzuki Experts

    yadayada
    yadayada

    Level 3 Expert

    78919 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22326 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8836 Answers

    Are you a Suzuki Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...