Question about 2004 Volvo XC90

1 Answer

O2 Sensor replacement: Can any generic brand be used to replace the sensors. OEM part for 04 XC90 states 5-wire but internet says many 1-4 Wire sensors will work.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

Stay with a 5 wire replacement!

Posted on Jun 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 06 Hyundai 3.3 thats throwing a PO133 O2 sensor code-we put a brand new GOOD Oem sensor in bank 1 sensor 1, disconnected the battery and bout 3 starts later on with the check engine light so we...

Are you absolutely sure that you replaced the correct side sensor. It has two front (upstream) oxygen sensors. Aftermarket intake or exhaust components can cause this code. Poor connection at O2 wires possible. Could be wrong part number sensor.

Apr 20, 2014 | Hyundai Sonata Cars & Trucks

1 Answer

Is there a o2 senser fuse in fuse box if my 97 mazda protege

Has the sensor 4 wires, if yes it has a fuse. The two white wires are for a heater, use a volt meter, should get 12volts across these wires, black wire is an earth and the grey wire is the sensor. If the heater is not working (fuse blown) it will give that code. I have had this fault on a Seat, changed both sensors (180 pounds), then found a broken wire on the back of the fuse box?????????

Dec 30, 2013 | Mazda Protege Cars & Trucks

1 Answer

I have a 2007 jeep commander 3.7 reading a code p0032 after i replaced the o2 sensor with a ngk it is still reading the code what do i do next?

Check your wires. You may have a bad connection or broke wire. other than that you may have an issue with it running too rich or lean. The o2 sensor will turn on the check engine light if its out of specs.

Jun 14, 2012 | Jeep Commander Cars & Trucks

2 Answers

I have a 2004 Dodge Grand Caravan with a 3.8 and recently replaced the upstream O2 sensor and now get a p0135 engine code. What is the problem? I used a Bosch sensor. I was able to clear out the code but...

rule of thumb on any vehicle. always use the factory sensors for anything. they just are made for your vehicles computer. them online and shop around for best price.

Aug 26, 2017 | 2002 Dodge Grand Caravan

1 Answer

I have a 2006 Hyandai elentra automatic check engine light came on code p2626 from research I've found out its the oxygen sensor in bank 1 section 1 problem I had was when getting a new o2 sensor auto...

The 4-wire sensor is for vehicles rated as Ultra Low Emission Vehicles. If you have a 5-wire connector, your vehicle isn't ULEV. NTK is the brand installed at the factory and that's the brand you should use. Go to and you can buy it there if your local store can't get that brand.

Aug 30, 2017 | 2006 Hyundai Elantra

1 Answer

O2 sensor(s) need replacing. Does anyone know where they are located and how difficult it is for the average guy to replace? Also, which ones do I buy,,1 wire, 2 wire, 3 wire, etc.

You do not change any O2 Sensors based on an OBD2 Code

You change sensors,front 2 only at 80,000 to 100,000 miles

You use a 22 mm wrench or special O2 socket.
Some veh use a diffent size

Easy job,they are in the front of the converter
or pipe before it

The number of wires with be year and application

You get an OEM Type, NOT a universal cut and splice

5 minute job per side

Feb 01, 2011 | 1996 Isuzu Trooper

1 Answer

I have a 04 sequoia and the codes p0031 and p0051 are coming up. How do I fix this?

Trouble code P0031 means: Oxygen Sensor Heater Control Circuit Low - Bank 1 Sensor 1 .
Error code p0051:replace O2 sensor ($75-150 depending if OEM) before catalytic converter. need O2 socket ($10) to get at and tough to get to if vehicle isn't at least on a ramp.

Nov 22, 2009 | 2004 Toyota Sequoia

2 Answers

Check engine light

Sometimes can be prematurely dirty air filter, sets off the air flow sensor, which sets off the o2 sensor. So might try new air filter first and erase codes and then see, before you spend more bucks than you need; then if codes return, do the flow mix sensor.

Apr 19, 2009 | 2006 Honda Civic Hybrid

1 Answer

Repacing an OEM oxygen sensor with a universal Oxygen sensor

Visit the on-line store, known as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem.
toyota celica

Oct 21, 2017 | 2001 Toyota Celica

Not finding what you are looking for?
2004 Volvo XC90 Logo

Related Topics:

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides