Question about 2001 Chevrolet Silverado 1500

1 Answer

2002 Chevy Silverado, crank sensor installed. can't start truck.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 71 Answers

After installing a new crank sensor, a Tech 2 will need to be hooked up in order to complete what is called a relearn procedure on the new crank sensor. Until this is done, your truck's ECM is unable to determine when cylinder #1 is at TDC and electronic timing is unable to be performed. Need to tow to GM dealership for this proceedure.

Posted on Jun 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 chevy silverado cranks but wont start.


check the crank sensor that seems to cause intermittent starting stupidness. had that problem on my silverado.

May 22, 2014 | 2002 Chevrolet Silverado 1500

1 Answer

2002 chevy silverado 5.3L 2WD wont crank ,diagnostic tool read code C0226,could this stop it from starting?


How did you find out the code? A good scranner if you no how to use it (Properly) Will all so show you what sensor detected the problem, End give you a idea what to look for,

Nov 07, 2012 | Cars & Trucks

1 Answer

2002 chevy 3500 duramax 6.6 ran hot now cranks but won't start


Check spark plugs, leads, distributor cap & rotor arm, fuel pump, fuel filter, coil pack(s), relays, replace any items that are suspect IE Fuel filter which has probably not been changed since new even though they should be changed on all vehicles every 18 months, all of this can be done at home & will save you a lot of bucks in mechanic/garage fees,

Sep 21, 2012 | 2002 Chevrolet Silverado 3500

1 Answer

How do i reset passlock on 2002 Chevy Silverado, 4.3


I have a 2002 Silverado 1500 My truck Cranks but will not run . With security light flashing . I've done the 10 minute method It works . for a week or two . What I've done is put my key in the ignition with very little pressure upward works every time at this point I think its a worn key. I'm waiting for it to do it again so I can try it with my original spare key. I've read it could be BCM connection / lose wire connection that inserts to pass lock sensor / or the pass lock sensor is dirty between sensor and key cylinder . I hope this helps Good Luck .

Sep 20, 2012 | Cars & Trucks

1 Answer

1997 chevy silverado starts one day next will not start


The next time it does not start have someone crank it over while you tap on the mass air flow sensor,if starts then remove the mass air flow sensor and clean the small wires inside of it using a non-chlronated brake cleaner let dry 10 minutes then re-install.

Jun 22, 2012 | 1999 Chevrolet Silverado 1500

1 Answer

I have a 2002 chevy silveroda . I need to find the location of the crankshaft position sensor


should be on bottom of crank on left side behind the pulley.. the big metal ring with teeth on it on front side of motor..

Dec 02, 2011 | 2002 Chevrolet Silverado 1500

1 Answer

2000 chevy silverado just rebuit transmission, new starter, and checked all fuses. it cranks but will not fire (start) more I crank the more I smell gas. What could it be? why it will not start?


try checking the crank sensor. if a crank sensor goes bad or is damaged it will not allow the plugs to fire but you should still have fuel pressure. also check all connections.

Jul 01, 2010 | 2000 Chevrolet Silverado

1 Answer

Crank Sesor Location?


Ck Front of engine around the crankshaft pully.

Sep 16, 2009 | 2001 Chevrolet Silverado

1 Answer

02 chevy vortec v6 wont start


it sounds like the crank sensor

May 21, 2009 | 2002 Chevrolet Silverado 1500

1 Answer

2002 chevy siliverado will turn over, but will not start


I would verify fuel pressure is in spec.On the back of the motor on the drivers side you will find a shrader valve(kinda like a valve stem on a tire)Its just alittle larger.You can buy a fuel pressure gauge at your local parts house and they can give you the spec as well.If its not in spec the pump is in the gas tank.

Mar 08, 2009 | 2002 Chevrolet Silverado

Not finding what you are looking for?
Cars & Trucks Logo

1,130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...