Question about 2012 Mazda 3 i Touring 4dr Hatchback 2.0L 4-cyl. 6-speed Manual w/SKYACTIV-G

1 Answer

Serpentine belt diagram mazda - 2012 Mazda 3 i Touring 4dr Hatchback 2.0L 4-cyl. 6-speed Manual w/SKYACTIV-G

Posted by Anonymous on

  • Douglas Hurton Apr 26, 2018

    Can you put a serpantian belt on wrong

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

2012 Mazda 3 I touring Skyactiv - Takes a 38" 6 groove serpentine belt- Very hard to find. The only place I found besides the dealer it Advance Auto but they had to order from the warehouse. There are three grooved pulleys and a smooth tensioner. To relieve the Tensioner you will need a shallow 17MM socket, it is a bit difficult to see, but if you stand on the passenger side the mount point for the socket is to the left of the tensioner shock. The Tensioner shock is just above the smooth tensioner pulley. All the threaded pulleys' (Drive, A/C, and alternator are within the serpentine belt, the tensioner pulley is outside the belt pushing down on the belt. The easiest way to replace this belt, First remove the old belt by placing the socket on the mount point and pulling up on the ratchet towards the rear of the car, then pull belt off. Next remove socket, place the belt over the drive pulley (this is the one on the bottom to the rear of the engine. ( you will see there is another belt on this pulley on the back side.), then put the belt over the A/C pump bottom front. Keep tension on the belt so it stays in place. Now put that socket back on, push up to lift the tensioner pulley and slip the belt over the alternator pulley. Make sure the belt is sitting properly on each pulley and under the tensioner pulley. Good luck. I have run into quite a few problems finding parts and information for this particular model. Good luck. Hope this was helpful

Posted on Jul 27, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 2000 Mazda MPV

I NEED THE DIAGRAM FOR SERPENTINE BETL FOR MAZDA 2000 MPV

Posted on Jan 20, 2009

bschilz
  • 2049 Answers

SOURCE: serpentine belt diagram mazda 6 2005

Here are links to the diagram...

If your engine is the 2.3L 4 cyl... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S7042

If your engine is the 3.0L V6... http://www.gates.com/common/part_locator/view_diagram.cfm?id=S6036

Posted on Sep 01, 2009

  • 1757 Answers

SOURCE: serpentine belt diagram Mazda MPV

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2001/make/mazda/model/mpv/2001_mazda_mpv_drive_belt_routing_diagram.htm

Posted on Mar 06, 2010

  • 1757 Answers

SOURCE: I need a serpentine belt diagram for a 2003 mazda

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2003/make/mazda/model/tribute/2003_mazda_tribute_drive_belt_routing_diagram.htm

Posted on Mar 06, 2010

  • 1757 Answers

SOURCE: replacing serpentine belt

Click on the following direct Link. It has the Serpentine Belt Diagram that you will need depending on your engine size (2.0L or 3.0L) and your options (AC/No AC ect.).
http://www.2carpros.com/car_repair_information/year/2001/make/mazda/model/tribute/2001_mazda_tribute_drive_belt_routing_diagram.htm

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.


Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

Posted on Mar 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for serpintine belt for 2012 mazda 2 1.5l


Google "Dayco serpentine belt diagrams" for a pdf booklet of diagrams.

Dec 09, 2016 | Mazda Cars & Trucks

1 Answer

Replace alernator and serpentine belt


Below is the master help link provided to go through belt routing diagram:---Timing belt, drive belt, serpentine belt, accessory belt, fan belt, engine belt routing diagrams for all types of car models?
Click the link below: ----

http://carbeltrouting.blogspot.in/2012/02/timing-beltdrive-beltserpentine.html
----------This will help. Thanks.

Jan 23, 2012 | 2001 Mazda MPV

1 Answer

Need a diagram for 1996 mazda protege serpentine belt


you don't have a serpentine belt just two drive belts one power steering and ac to crank belt and one alt belt

Nov 25, 2011 | 1996 Mazda Protege

1 Answer

PLZ I NEED FOR A 04 MAZDA MAZDA 6 V6 THE SERPENTINE BELT DIAGRAM THANK YOU SOO MUCH FOR UR HELP !!!


Hello ezzywaylogis,

Below is a diagram of the belt routing.

netvan_209.png

I hope this helps.

Regards,

Jerry

Aug 28, 2011 | 2004 Mazda 6

1 Answer

I need the serpantine belt routing diagrams for a 1993 Mazda 626 v-6


Question Posted by Asker under the 1994 Mazda for a 1993 Mazda.

Click on the following: free, direct Link. It has several Diagrams including the Serpentine Belt Diagram for your 1993 Mazda 626 2.5L DOHC V6. It has the 2.0L DOHC 4-Cyl Diagrams as well as Instructional and Directional Diagrams that will help you.

http://www.2carpros.com/car_repair_information/year/1993/make/mazda/model/626/1993_mazda_626_drive_belt_routing_diagram.htm

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

Apr 03, 2010 | 1994 Mazda 626

2 Answers

I need a diagram on How to change a Serpentine belt for a 97 mazda protege


Have you checked Autozones website? Thats where I usually go to get all the details and diagrams I need

Oct 25, 2008 | 1997 Mazda Protege

Not finding what you are looking for?
2012 Mazda 3 i Touring 4dr Hatchback 2.0L 4-cyl. 6-speed Manual w/SKYACTIV-G Logo

3,235 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

84027 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22483 Answers

Jonah Oneal

Level 3 Expert

14065 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...