Question about 1986 Toyota Pickup 4WD

1 Answer

Rear Seals Blown Out

I have a 1986 toyota 4x4(locking front hubs}5 speed mini pickup truck. (22R-4 cylinder) Here's my problem the rear seals are blown out and I am experiencing no support from my local automotive stores as to what I need per replacing-fixing the rear seals. Please help!Sincerly ; In the middle of a diaster.

Posted by on

  • ashortzs39 Jun 20, 2009

    Unfortunately I am lost. My 1986 4wd 22r - 4 cylinder mini pick-up is a manual. Does this solution still apply? Had a friend help me out and replace the rear inner seals on both sides,but it seems to still be leaking. It seems to have slowed down measurably but it still leaks. What do I need to do?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

The rear seal can be replaced but not without pulling the transmission, then you remove the seal holding case knock out-the seal and find the number on the seal and buy one and replace it and the gasket to the seal holder, also buy a speedy sleeve for the crank or you will find it leaking again.

Posted on Jun 17, 2009

  • Bruce Hathcock Jun 20, 2009

    Well the seals your talking about I assumed the rear wheel seels tell me exactly where they are and I will provide a fix for you.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Put new timimg chain on 1984 toyota pickup,22R was running great all of the sudden it locked up,will turn about 1/4 turn each way ????? Any idea of the problem,this engine is difficult to find


When u put a new chain on. Water pump,seals,guides should also be replaced. New force causes pressure on old parts. Library sec629 has shopmanualsx

Apr 02, 2015 | Toyota Pickup Cars & Trucks

1 Answer

Cost replace rear main seal toyota camry


Four cylinder or V-6.

Both engines will require the removal of the timing belt to service the front crank seal. Both engines will also require the removal of the transmission to replace the rear main seal

either way way you would be looking at 3-4 hours for the front seal and 5 to 6 hours for the rear seal.

Apr 10, 2014 | 1997 Toyota Camry

1 Answer

Grease in rear wheel hub


The rear brake cylinders are located inside the hub with the brake shoes on drum brakes...(common in 2004 Rangers on rear only) The brake cylinders are a "wear item" with seals...we used to rebuild the cylinder with new seals...best today to buy new brake cylinders to replace the leakey ones...You will need to bleed all 4 brake line/wheel connections after the replacement. Hope this helps.

Oct 14, 2013 | 2004 Ford Ranger

1 Answer

I have a 5 speed Toyota 4x4 when u i put it in neutral i can push it forward but when i push it in reverse in locks up still in neutral what could it be help


are you sure it is first gear it is making when in 1. In park does the car lock up if you try to push it with the handbrake off. If not your problem is adjustment of the cable i.e. although the lever is in reverse the gearbox isn't.

Oct 12, 2012 | Cars & Trucks

1 Answer

89 toyota pickup torque specs. for flywheel and clutch bolts 22re 4x4


Thoroughly clean the flywheel bolts. Coat the first 3 or 4 threads of each bolt with sealant. Install the flywheel, aligning the previously made marks. Install the bolts finger-tight.
Tighten the bolts in a crisscross pattern and in several passes to the correct tightness:
  • 22R/22R-E manual trans-80 ft. lbs. (108 Nm)
  • 14-20 ft-lb for the clutch cover and
  • 50 ft-lb for the transmission mounting bolts.
Since you have the flywheel off, be sure and inspect the rear main seal. Now might be a good time to replace it. Be sure the rear flange of the flywheel is clean before re-install.
Be sure to inspect or, better yet, replace the bronze pilot bushing. I f you don't know how to get it out leave a comment. J


Thanks for using FixYa - a 4 THUMBS rating and POSITIVE TESTIMONIAL is really appreciated for the FREE answering of your question.

Feb 14, 2011 | 1989 Toyota Pickup SR5

1 Answer

Exp. sudden, total loss of brake pressure 1992


hi this sounds like you have a major leak possibly the master cylinder or rear slave cylinder has blown its seals, cheack under the vehicle at the rear and have a look at the back of the wheels if they are dark and verry wet or one is, then you have found the leak, you can also try looking under the hood, where the brake master cylinder is ( this is where the brake fluid is normally put in ) and check there to see if there is any damp/wet patches running down the bulk head/fire wall, you can also check the inside of the vehicle where the brake peddal is attached to the vehicle and see if the carpet is damp, this will be the master cylinder seals have blown, and will need replacing, unit or seals depends on what you can get .....hope this helped

Mar 15, 2010 | 1992 Toyota Pickup

2 Answers

I have an 86 toyota 4x4 with the 22r motor. my


it could just be the switch,, or more likley to be the resistor burned out or the reostat? (same thing realy)

Oct 27, 2009 | 1986 Toyota Pickup 4WD

1 Answer

1989 Toyota PickUp Truck V6 4x4 Any sealants or caulking type seals to put around very bad leak around the transfer case and the rear main seal?


there is no way to fix a rear main leak except to replace it, sorry but if there was a way to jerry rig this every tech would use it.

Jul 27, 2009 | 1989 Toyota Pickup SR5

1 Answer

Rear axle bearings


There are 4 bolts for each rear axle. They are located behind the rear brake drums. Remove e-brake cable from rear drum and take off brake line.(carefully). I recomend draining and changing your rear differential fluid too, because if the fluid by run out of axle housing. also you should replace the seals for the axles of if you are changing the bearings. When you are done don't forget to bleed your brakes, and hooking up e-brake cable. I hope this answers your question.

Jan 28, 2009 | 1986 Toyota Pickup 4WD

3 Answers

Hello, 1986 Toyota 4X4 Truck 22R carb engine manual transmission. My son was driving it and the rear wheels locked up. Driving in 2 High mode. He got the truck pulled over to the side of the road using 4X4...


I've seen a similar issue on other transmissions where the shifter slips out of the slots in the shift forks, either due to shifter bushing wear or just general wear on tte trans. It can usually be remedied at least temporarily by popping the shifter top off the trans and resetting the forks all back to nuetral and then reinserting the shifter. It gets jammed when two forks are trying to engage two different gear sets.
On one of the 4x4 sites, they tell you how to replace the shifter bushings, cheap fix if you are lucky.
Good luck.

Dec 09, 2008 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

334 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...