Question about 1995 Chevrolet C1500

1 Answer

Front right brake sticks intermediately. caliper was replaced but didn't help

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 2,007 Answers

Brake line is collapsed internally, and is acting like a one way valve.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hi ,i have a vw scirocco 1987 8valves,all the brakes are new,even the lines ,master cylinder,galepper,pads,rotors,drums.when the car is hot the pads stick on the front disk,everithing is new?what is the...


Hi
Well, I really think you may find the problem only between two things: Caliper, pads or brake shoes, Beacuse I guess If you bought new drums you bought new shoes too didn't you? But if you're sure it is in front disk, then, you just have to check, you got the right caliper and pads and check the caliper is well adjusted and installed I hope this helps good luck!

Aug 05, 2011 | 1987 Volkswagen Scirocco

1 Answer

Occasionally after driving and stopping my right front brake caliper is slow to release,a few times it actually stayed applied and become extreamely hot. When this happen I opened the bleeder screw...


Replace the rubber brake hose on that side....they are prone to rotting on the inside and letting fluid pass through it ,but not letting it back out,causing caliper to stay hung up and making you believe caliper is sticking,and opening the bleeder lets off pressure for a little while...I have seen many unneeded calipers be replaced,and then problem is still there.Now I will almost always replace both hoses when doing a front caliper change....they get old too...Good luck..Lee

Oct 31, 2009 | 2000 Chevrolet Venture

1 Answer

Front breaks are smoking


caliper is sticking or pads are sticking ,proportioning valve with vehicle jacked up and supported and wheel removed inspect pads and rotor for damage excessive wear if good- turn hub/rotor by hand have someone assist u by stepping on brake observe brake caliper stop then release brake piston should release slightly from pad try turn hub again w/out touching brake if stuck in place replace and caliper released replace pads if caliper still clamped remove caliper and inspect for leak or damage compress caliper and try brake again if does if sticks again replace caliper

Oct 13, 2009 | 1988 Dodge Ram 50

2 Answers

Just replaced brake pads on my 99 chevy p.u. seem to be fine when they are cold but feel like they are grabbing when they heat up. What could be the problem?


Hope you are talking about the front brakes,First check to see if the brakes are releasing the brake rotor.If they are not,it is posible the slide on the caliper need cleaning and lubed.Also could be the brake hoses colasping,and not allowing the piston in the brake calipers to release.Did you have the rotors turned?It could have something to do with it.Also what it probley is,that when you pushed the piston back in the caliper,you didn`t remove the master cylinder top off.Bleed the right front caliper,then the left front caliper,and then the master cylinder.This should clear it up.

Sep 24, 2009 | 1999 Chevrolet C1500

3 Answers

2001 silverado 1500, just put on new pads rotors and 1 new caliper, the brakes are spungy, the wheel with the new caliper is sticking and the front passanger brake too, i cant figure out why.


Replace both front brake hoses.....they collapse on the inside and will not allow fluid to retract...caliper was probobly fine.....this happens a lot....good luck...Lee

Jul 22, 2009 | 2001 Chevrolet Silverado 1500

2 Answers

Caliper won't release on right front brake--everything is new, replaced because of that problem but no fix


Check the left rear brake for sticking on also, if it is then you have a master cylinder problem. replace brake master cylinder but check the adjustment of the brake light switch first. the switch is above the brake pedal, make sure it is not holding the pedal partially on.

Jul 16, 2009 | 1985 Chevrolet Sportvan G20

1 Answer

Brakes are sticking after application front right being the worse


Hi,


I've had a similar problem as what you describe. For me it was as simple as replacing a faulty front brake line. Never had any problems since. Hope this will help you narrow it down some.

Mar 31, 2009 | 1989 Honda Prelude

1 Answer

Brakes Sticking


u have an obstruction in the brake line that feeds that caliper so u need to replace the hole line or u might get lucky and just replace the rubber extension of lie at the caliper. hope this helps please rate me

Jan 12, 2009 | 1999 Dodge Caravan

Not finding what you are looking for?
1995 Chevrolet C1500 Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6910 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...