Question about 1984 Cadillac Eldorado

1 Answer

84 Cadillac Eldo convertible. I'm down to the last stages of getting my left rear window and regulator out. Need help on steps to remove it. Seat is already out, and so is the plastic interior wall that has ashtray. Down to the metal.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

Ok the Regulator is most Likely RIVETED Into the Panel, Use a Small Punch to Knock OUT The CENTER PIN of Rivet ALL Of Them. Then You must DRILL out the Middle of the Aluminum Rivet
These should be replaced with bolts and locknut's , Drill until heads can be shaved off and shave them off. after this regulator must be in a position that is COMPACT Enough to Remove it out of the Largest Access Hole In Panel. REVERSE Procedure To Install.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My rear windows on my 2004 DHS do not come down


I have had to replace all of my window regulators in my '04 Deville. Can get them online for 40-60 bucks each, without the motor. It verify it is the regulator and not the motor, simply try to push the window down (without power). If it goes down (careful not to lower it completely), then push back up, and get online and order one. They are position specific, i.e. left drivers or right rear. The door panels are very simple to remove, but can be challenging to install. Check out youtube. There are some good video showing just how to get to it. It takes me about 20 minutes to do one.


Now if the problem is not the regulator, you can still easily remove the panel to gain access to the switches and their plugs. Use a volt meter to check for voltage. Also, as you stated "windows" will not go down, is this with just the drivers controls or each individual rear switch as well?

The most common problem on the '04 Deville is the regulators. Typical cheap junk design from GM, has a plastic connector to attach the regulating cables to. They simply break. Had they spent an additional nickel and used metal, thee would not be a problem. Good luck!

Jul 09, 2014 | 2004 Cadillac Deville

1 Answer

Need to know what steps needed to remove left 1/4 glass on my 1999 celica convertible


take out the back seat-lower and also the seat back-remove the trim card and you should be able to access the bolts that hold the glass onto the regulator-cheers Denny

Nov 10, 2013 | 1999 Toyota Celica

1 Answer

Power window fuse


That is not a fuse issue. Your window either jumped track, Or MOST LIKELY the worm gear is striped and the regulator mortor need to be replaced. FOUND THIS ON Amazon.
ACDelco 15269139 Cadillac SRX
Rear Driver Side Window Regulator Assembly by ACDelco







Price:
$85.35 &
FREE Shipping. Details

Deal Price:





Only 2
left in stock (more on the way).
Ships from and sold by
Amazon.com.

Want it Wednesday, Aug. 28?
Order within 19 hrs 15 mins and choose
One-Day Shipping at checkout. 9 new from $85.35

Aug 26, 2013 | 2004 Cadillac SRX

1 Answer

Rightside, rear window motor failed. or the mechanical part perhaps. what i want to know is how to get to that part of the car. The driver seat behind the panel. Thank you wery much! Patrik


Long job and not for the faint of heart.

Open roof to rear.

Pull up on rear seat bottom and remove it.

Remove center panel.

Remove three Allen head bolts down behind seat cushion back.

Lift off head rests...pull up.

Raise top just enough to make side flaps flip up.

Remove nut at top rear corner.

Remove Nylon/plastic push lock rivet where seat belt goes through panel... top corner.

Pull panel off mounting pins...will sound like your breaking it !

Lift panel to access seat belt bolt and unplug Flip-Up panel motor.

Remove cable from it's clip.

Remove loom thro' panel.

Pull seat belt thro panel.

Set panel to one side.

Remove Torxs bolts around black plastic panel for speaker.

Unplug speaker.

Pull loom thro' hole.

Remove two Allen and 5 hex bolts where window would come out. if it worked.

Pull up plate and remove rubber seal to one side and then remove plate. remove two nuts at bottom of regulator and one half way up towards front.

Lift regulator and window glass up thro' top to gain access to three nuts holding glass tho regulator.

Lift out window and then regulator....little maneuvering and levering required.

FYI....Take digital pictures as you remove stuff for later reference.


New regulator and glass is around $600.00 from dealership and only the dealership.

Jan 12, 2011 | 2004 Volkswagen New Beetle Convertible

2 Answers

Need to replace a broken window on rear passenger 1999 jeep chero


This information can help you to fix it:
- Section-08s-Power-Window-Systems-Ewj8s
- Section-23-Body-ewj23S (Rear Door, page 41 and next).

Good luck (remember rated this help).

Sep 09, 2009 | 1999 Jeep Grand Cherokee

2 Answers

My 1976 cadillac eldo convect bicen needs new parts


try factoryonlyparts.com also try searchhing online for car clubs that can help you find parts.

Jun 08, 2009 | 1976 Cadillac Eldorado

1 Answer

No acceleration, performance dies out


What shape is the catalytic converter in? If it plugs up you have back pressure that causes issues.

Sep 01, 2017 | 1991 Cadillac Eldorado

2 Answers

2003 volkswagen beetle covertible quarter panel removal


I do not recommend this job unless you are a seasoned mechanic, VW dealership charges $1000 for a reason. They almost earn it on this one. but heres how it's done or how I did it any way. the complete job took me 4 hours and I been at this for 30 years. But a lot of this time was figuring out how it came apart. First, drop the top, pull up on seat bottom and remove it, remove center panel, remove 3 allen bolts at bottom on seat back and remove. headrests, they just pull off, raise top just enough to make hinged panels flip up. remove nut at top rear corner of side panel. you can see the back side of the nut and bolt it is on from the panels that flip up. Remove Nylon push lock rivet where seat belt goes through panel on rear, top, corner. Pull out on panel to release it, there is 5 or 6 nylon locks that just pull out of holes in the body. It will sound like your breaking it when the locks pop loose, or mine did. then lift to gain access to remove seat belt bolts and unplug flip panel motors. remove cable end from its clip. Pull seat belts through panel. Set panel a side. remove torx head bolt around oval panel that speaker is mounted on. unplug speaker and regulator and pull wire harness thru hole. remove 2 allen and 5 hex bolts at top where window would come out if it worked. pull up on plate and move rubber window seal to the side to remove plate. remove 2 nuts at bottom of regulator and one about half way up towards front, lift regulator and window up through top to gain access to 3 nuts that hold window to regulator, from the top lift window out first then regulator. Reverse to assemble it.

Aug 12, 2008 | 2003 Volkswagen New Beetle Convertible

1 Answer

Window track


I do not recommend this job unless you are a seasoned mechanic, VW dealership charges $1000 for a reason. They almost earn it on this one. but heres how it's done or how I did it any way. the complete job took me 4 hours and I been at this for 30 years. But a lot of this time was figuring out how it came apart. First, drop the top, pull up on seat bottom and remove it, remove center panel, remove 3 allen bolts at bottom on seat back and remove. headrests, they just pull off, raise top just enough to make hinged panels flip up. remove nut at top rear corner of side panel. you can see the back side of the nut and bolt it is on from the panels that flip up. Remove Nylon push lock rivet where seat belt goes through panel on rear, top, corner. Pull out on panel to release it, there is 5 or 6 nylon locks that just pull out of holes in the body. It will sound like your breaking it when the locks pop loose, or mine did. then lift to gain access to remove seat belt bolts and unplug flip panel motors. remove cable end from its clip. Pull seat belts through panel. Set panel a side. remove torx head bolt around oval panel that speaker is mounted on. unplug speaker and regulator and pull wire harness thru hole. remove 2 allen and 5 hex bolts at top where window would come out if it worked. pull up on plate and move rubber window seal to the side to remove plate. remove 2 nuts at bottom of regulator and one about half way up towards front, lift regulator and window up through top to gain access to 3 nuts that hold window to regulator, from the top lift window out first then regulator. Reverse to assemble it.

Aug 05, 2008 | 2003 Volkswagen New Beetle Convertible

Not finding what you are looking for?
Cars & Trucks Logo

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...