Question about 2001 Volkswagen Beetle

1 Answer

Drivers window keeps coming off track. It tilts forward when it is raised. It can be pulled upward until it snaps back onto track, however if it is allowed to completely descend, it usually snaps out of track again.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 236 Answers

The is a plastic rest for the widow that beaks through time. take off the door panel to see if that is it

Posted on Jun 18, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to replace drivers side window on 95 chevy truck


Remove interior door trim. There will be screws as well as plastic pins that have to be pried out. Wind the window all the way down. There will be some tracks in the lift mechanism with rollers that are attached to the window frame. Locate and remove the bolts that secure the frame. The window should then come out.

Mar 05, 2015 | Cars & Trucks

3 Answers

Front seat will not slide forward? The seat will move up and down, tilt, and the lumbar works? Even the heated/cooling seat works? What do I need to look for and how do I fix it:?


The power seat in the truck has 3 motors, one of them is not working, the most common cause of this is the power seat switch is defective, it is often the forward and reverse seat positioning switch that fails because it is the one that is most used. If the switch checks ok then you will need to replace the the power seat track assembly, Ford does not sell any parts for the track, it is only available as one complete unit, I know this because i retired form a Ford dealer. Please rate my help for Fixya. Thanks

Dec 29, 2011 | 2007 Ford Expedition Eddie Bauer EL

1 Answer

Trying to replace a power window motor on an 03 maxima but can't get motor assembly out from behind door and now window is off track as well. Need to know how to get window back in track. Do I need to...


The window need to be lowered to get to bolts that hold it to regulator,then pull glass all the way up and wedge it there,next is to remove all the bolts securing the regulator to door,now work regulator out and replace the motor, with regulator out remove the wedge tilt glass until you are able to get it on the front and rear track ,on track now pull window back up and wedge it.install regulator and bolt it up to door,move regulator with switch to line up bolts to attach glass, now lower glass onto regulator arms and tighten, hope this helps.

Sep 12, 2010 | 2004 Nissan Maxima

2 Answers

My driver side window wont roll down, manualy, it rolls down on an angle. How do I fix it?


Thanks for the info, I think I can help. Roll the window down until it tilts forward just a little. Once the glass has tilted forward, do you see a tiny hole in the rear upper corner of the glass? I think your model has a small piece of plastic that hooks into that hole and rides up and down the vertical window track to hold the glass straight.

Jan 23, 2010 | 2000 Chevrolet Venture

1 Answer

Window tilts forward when going up


The forward track channel has either rusted out, broken, or the sash clips to help keep the window level broke. We have seen all the above, but most likely is the sash clips that glue onto the lower window broke. The door panel will have to be removed, the old clips, heated with a HOT heat gun and removed, and new ones installed. Pretty easy fix with the right equip.

Jan 19, 2010 | 2000 Pontiac Montana

1 Answer

How do I remove my pontiac g6 driver seat?


1. Take off the head rest. 2. slide seat forward until the 2 rear bolts are exposed on the track 3. Remove bolts 4. the seat that lifts out like a van seat. you need to tilt it forward then pull it up and back and it will come out. then maneuver it out of the door.

Jan 11, 2010 | 2009 Pontiac G6

1 Answer

The power window motor is dead. I purchase a used/new one at Rockauto. This is a 2003 Nissan Murano, I took the door panel off and replaced the motor. However in doing so the window fell int othe door. How...


first you''ll need to get it back on track if it's off now and get it, closer to the closed position to verify that it is actually fitting properly, then you'll need to use the power switch to raise the mounts to where they are at the same level as the nylon glass mounts to install the 2 bolts you removed, or, lower the glass, while in the track it glides in, to the point where you can install those 2 bolts. The glass may just slide upward from where it is & then you put the bolts in or you may need to tilt & turn it carefully until you can get it back on track.

Best I can do from here,
good luck.

Jan 01, 2010 | 2006 Nissan Murano

1 Answer

How do I remove 2009 BMW 328I front headrest


Pull the headrest up to the most extended position, tilt it all the way forward, then you will want to **** or yank upwards slightly to clear the last little groove. Pull up on the chromed stalks, one at a time. This should work. Once you know how much force to apply the first time, it's a snap afterwards.

Oct 03, 2009 | 2007 BMW 328xi Sports Wagon

1 Answer

I heard a snap in the door as I pulled the button up to raise the driver side window. Now the window has slid all the way down into the door and will not raise back up. What might I have heard snap, and...


Hard to say..
The best wat to tell is take the inside door panel off to see what is going on.
Could be a brace snapped and the window fell off the track.. Or a part of the linkage broke..
Good luck..
Rate me good ;o)

Jul 10, 2009 | 2003 Honda Element

1 Answer

How do i replace a 1992 honda accord drivers front window


IF you scroll over the title, you can see the word "window". Raise the window about two inches. Remove the interior door panel: Remove the inner door handle screw, push the handle forward, pull it out some, unclip the actuating rod, you may also have to unplug the power lock switch. Remove the screw in the arm rest. Remove the plastic plug at the forward upper corner of the panel. Remove the black plastic triangle at the insdie of the side view mirror (it just snaps in place). Pull the bottom of the panel away from the door to disengage plastic clips, then lift the panel off the door and disconnect the electrical connectors. Pull the plastic away from the bottom part of the door (you'll probably end up tearing it). There are two bolts that hold the window glass to the regulator mechanism, remove those and the glass can be pulled up through the window opening. If necessary, the bottom of the window tracks (a screw at the bottom of botjh) can be loosened to loosen up the window.

Jan 09, 2009 | 1992 Honda Accord

Not finding what you are looking for?
2001 Volkswagen Beetle Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76051 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...