Question about Ford Windstar

1 Answer

No power to inside but van will start fine... the only time the power inside works is when the key is turned back... HELP

Posted by on

  • lippert_davi Jun 17, 2009

    i'll check that but it started just yesterday after the #10 fuse was replaced with a 30 amp fuse instead of a 10

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 87 Answers

FAULTY IGNITION SWITCH

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a renault kangoo 2007 ( mexican van ), and few times cut off, why ? I don't know, can you help me please


sounds like an ignition switch problem sometimes key is making contact to start and not other times

Aug 06, 2014 | 2007 Renault Kangoo 1.9

1 Answer

Why does my van try to start itself when i connect the battery cable with no key in ignition?


KEY CYLINDER IS STUCK IN CRANK MODE. PUT IN KEY AND TURN OFF , IF THAT DOESNT WORK, REPLACE CYLINDER. KEY IN THIN SCREWDRIVER FROM UNDER CYLINDER SLIDES OUT, DROP IN NEW ONE. SHOULD WORK

Jan 11, 2014 | 1996 Chrysler Town & Country

1 Answer

2000 Pontiac Montana wont start, no power to vehicle


I suspect an ignition switch problem, you need to check to see if when you try to start it if there is power to the signal wire at the starter. If there isn't, check the same wire at the ignition switch, if there still is no power, check to make sure the grounds from the firewall are secure and they have near zero resistance between the firewall and the negative battery post. Check to make sure there is power getting to the ignition switch, if there is none, then you have a broken fusible link under the hood

Apr 21, 2013 | 2000 Pontiac Montana

1 Answer

Turn signals stopped working now no power


I concur this is a power supply fault of some sort, insure your battery connections are maintained, meaning clean and good of contact, obtain a voltmeter and test the voltage at the battery contacts it should be about 12.5 or higher, turn the key on and try to start, noting the voltage, if it drops below 11 volts, there's your fault if not a poor ground from the battery and the frame of your vehicle may be faulty but boosting your vehicle from another sports battery fault

May 05, 2010 | 1998 Plymouth Voyager

2 Answers

Ignition locked will not turn


easiest way to handle this problem is as you turn the key turn the steering wheel back and forth not real hard bust firm and try and turn the key foward and back at the same time. usually what happens is the little detente inside the column gets stuck just right and stops the tumbler from moving

May 20, 2009 | 2004 Jeep Grand Cherokee

1 Answer

Dodge Caravan Stalls, won't turn over


i have the same van (2003), same problems, the deler just replace my PCM cost me $950 van works fine untill now.

Apr 25, 2009 | 2003 Dodge Caravan

1 Answer

It takes about 5 minutes for my van to start every morning then it works fine all day


Try turning the key on don't try to start turn it back off for 5 secs. turn back on repeat 4 or 5 times then start it. If it starts you have a fuel problem. Put pressure gauges on it you will see a pressure drop after you turn off the key. Either the fuel pump is bad or your pressure regulator is bad

Mar 08, 2009 | 1994 Chevrolet Lumina APV

4 Answers

Dodge caravan 1998 start problem (alarm set) ,the instument panel is not working and if i start , after 3-4 tryes,is shuting down in 3 seconds, any help?


I have had the same trouble with my 1998 Dodge Caravan, so has my neighbor on both of his caravan vans and We have found that if we slap down on the dash above the temperature gauge it will work just fine.

we both lose speedometer and fuel guages too! Same fix

about once a month I will have to slap it, to get my guages back, and stop the alarm.


I believe it is a bad soldiering connection in the dash but it is not worth chasing it down when I can get by without it.

when the post said the van worked fine after being towed it is because the connection was made while the van was jostled around being loaded and transported

Nov 07, 2008 | 1998 Dodge Caravan

1 Answer

Citroen C15 Diesel Van.


It definitely sounds like the electrical part of your ignition isn't working properly.When you turn the key, the lck and tumbler turns on the ign. switch in which sends power to the rest of the car.

Jun 22, 2008 | 2006 Peugeot 505

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...