Question about 1999 Chrysler Concorde

1 Answer

How do i loosen the tensioner on the pulley to remove the belt on a 1999 chrysler concored 2.7

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

You will see an idler/tension pulley, this pulley can be pulled up or pushed down. It is not connected to anything besides a mounting bracket. It is designed to move to adjust tension on the belt.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the serpentine belt on a 1994 concorde?


Remove the alternator/power steering pump and water pump drive belt to gain access to the air conditioning drive belt.
To remove and install the air conditioning compressor drive belt, first loosen the tensioner pulley lock nut, then turn the adjusting screw to raise or lower the tensioner pulley assembly Accessory Drive - 3.3L Engine or Accessory Drive - 3.5L Engine To adjust the air conditioning drive belt, loosen the tensioner pulley nut and adjust belt tension by tightening adjusting screw. Torque pulley nut to 54 N•m (40 ft. lbs.) after adjustment.
The Poly-V generator/power steering belt has an adjustable tensioner pulley located on the timing belt cover Accessory Drive - 3.5L Engine to maintain proper belt tension. To remove or install this belt, Release tension by loosening the tensioner pulley nut and adjustment bolt Accessory Drive - 3.5L Engine Reverse procedure to install and tighten belt to specified tension.

Jul 10, 2012 | 1994 Chrysler Concorde

1 Answer

Tensioner location on 97 chrysler sebring 2.5L 6 cyl


The tensioner pulley looks like an idler pulley, only with an adjusting bolt protruding out about 2 inches from just behind the pulley. Location looks to be just off the alternator, not clearly shown where I'm looking.
To loosen belt, you loosen the tensioner pulley nut, and then turn the adjusting bolt in to relieve tension. When putting the belt back on, adjust tension with adjustment bolt, then tighten the pulley nut. This is for Sebring Coupe, Convertible is different. Good luck.

Jun 22, 2012 | Chrysler Sebring Cars & Trucks

2 Answers

Could you please tell me how to replace the air conditioner belt on a 2002 Chrysler 300M


  • On the lower front passenger side of the engine there is an adjustable idler pulley for the AC. Loosen that center bolt a few turns to release the tension on the AC belt.
  • Remove the old belt.
  • Place new belt on.
  • Tighten the idler pulley bolt until the belt is snug.
  • Job complete.
  • Hope this helps and thank you for using FixYa.

Regards, Tony

Jun 14, 2011 | 2002 Chrysler 300M

1 Answer

How to put on serpentine belt


Hi,

The tools required are:
1/2-inch drive ratchet
2 - 1/2-inch drive 8-inch extensions
1/2-inch drive socket set

Please follow these steps to replace the serpentine belt on your 1999 Chrysler 300M:

1. Open the hood and prop it in place.

2. Locate the serpentine belt adjustable idler pulley on the front of the engine. This adjustable idler pulley will be closest to the top of the engine. Position a metric socket onto the ratchet and loosen the bolt in the center of the serpentine belt idler pulley.

3. Now please loosen the push bolt on the side of the idler pulley. It is a 15mm size and the push bolt on the side of the tensioner is 13mm. Pull off the old belt.

4. Loosen the tensioner pulley for the AC belt. The same steps need to be followed for this as well.

5. Next slip the AC belt on the back of the crank pulley and route it as per the diagram under the hood.

6. Now you need to tighten up the idler pully and the push bolt until the belt play is within factory specifications, then tighten the hub bolt in the center of the pulley as well.

7. The same thing needs to be done for the serpentine belt as well. Just ensure that you tighten up the bolts and have the specified play in the belt. Check the belt tension by pushing inward on the belt.

8. Crank the vehicle for about 15-20 seconds. Then turn it off and again check the tension in the belt. Adjust as necessary. You need to have about half an inch of play in the belt.

If this doesn't work for you or in case you need any further assistance, please comment and let me know, and I will be happy to assist you to further resolve your issue.

I will appreciate your feedback and positive rating for this solution.
Thank you.

Jan 13, 2011 | 1999 Chrysler 300M

1 Answer

Ho is the power steering belt on 2002 chrysler


Click on the following direct Link. It has the Belt Diagrams you will need, complete with Removal Diagrams and Directions. It also has numerous other helpful diagrams for use.

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.
4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/2002/make/chrysler/model/sebring/2002_chrysler_sebring_drive_belt_routing_diagram.htm

Mar 25, 2010 | 2002 Chrysler Sebring

1 Answer

1999 sebring serpintine belt installation


My sincere apologies for the severly delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it in case you still do.

Click on the following direct Link. It has several Diagrams for your Belt depending on your engine size and options (AC/No AC etc.) AND whether you have Tensioners OR Locking/Adjusting Bolts/Nuts.
IF APPLICABLE: These point out the direction of rotation for the Tensioner in order to loosen and reinstall the Belt.

IF APPLICABLE: These also point out where the Locking and Adjusting Bolts/Nuts are, to loosen the belt and remove; and reinstall the Belt and .

Standard Rules to Removal the Serpentine Belt with a Tensioner:
1. Find the Tensioner(s). (See Diagrams on Link)
2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening) rotating it\moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
3. Remove the loosened belt off one of the other more easily accessed Pulleys.


Standard Rules for Installing the Serpentine Belt with Tensioners:
a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them

Again my apologies...
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!

http://www.2carpros.com/car_repair_information/year/1999/make/chrysler/model/sebring/1999_chrysler_sebring_drive_belt_routing_diagram.htm

Dec 28, 2009 | 1999 Chrysler Sebring

2 Answers

Describe your 1999 Chrysler Town & Country Problem, Belt replacement , cna't seem to get belt tensioner to move when trying to remove belt.


The belt tensioner actually has a locking feature on it. Once the tensioner is in place you are supposed to tighten the bolt center of the tensioner pully which locks in in place. Try loosening this bolt slightly and then moving the tensioner.

Sep 08, 2009 | 1999 Chrysler Town & Country

2 Answers

Timing belt (replacing waterpump)


Most likely a tension pulley.

Aug 22, 2009 | 1999 Chrysler Cirrus

2 Answers

AC belt on 1999 Chrysler 300M


When you replace the AC belt you really should replace the serpentine belt as well, since you will have to take it off already. If you don't do it now it is inevitable that you will have to replace it in like 3 weeks anyway : )

You need to first remove the serpentine belt by loosening the nut in the center of the idler pulley. After that you will need to loosen the push bolt on the side of the idler pulley. The hub bolt is a 15mm size and the push bolt on the side of the tensioner is a 13mm I think. After you loosen it sufficiently, you will need to pull off the old belt.

Next you will need to loosen the tensioner pulley for the AC belt as well. It is the same process. The main issue is space. You will most likely need to raise your car to get at the right angles to loosen these pulleys.

Once you loosen the idler pulley in the same manner as you loosened the other, you can slip the AC belt onto the back of the crank pulley and route it as the diagram under your hood instructs you. Next tighten up the idler pully in the opposite way as you loosend it...tighten up the push bolt until the belt play is within factory specifications, then tighten the hub bolt in the center of the pulley. Do the same for the serpentine belt and you should be up and running in no time. I just performed these tasks on my 2000 300m and I wish someone would have told me this before I started my project. Hope this helps, Good Luck!

Mar 22, 2009 | 1999 Chrysler 300M

1 Answer

Belt came off 1998 chrysler sebring lxi


you have two belts . put the large belt on first . it goes around crank pulley air conditioning pulley alternator pulley.loosen tension pulley to adjust belt. tension. then you put the other belt on power steering pump pulley and crank pulley. adjust belt tension loosen power steering pivot bolt. that it.

Mar 16, 2009 | 1998 Chrysler Sebring

Not finding what you are looking for?
1999 Chrysler Concorde Logo

Related Topics:

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...