Question about Dodge Durango

1 Answer

How to change cable on electric window front driver side

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 323 Answers

The cable itself is not serviceable, you need a regulator assembly.

Posted on Jun 17, 2009

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 54 Answers

SOURCE: laguna 1.9dci

no. the unit has to be replaced. i have seen people trying different things but in the end it needs replacing

Posted on Aug 22, 2008

  • 1 Answer

SOURCE: electric window cable solution

I have the same truck and I had the same problem a few days ago. The dealer wanted $500 per window to fix it. I did it for $80 per window and it was an easy fix. Here is what I did.
1. Go the local parts store and get the appropriate window regulator.
2. There are about 8 screws that hold the door panel on the door, remove them. The door panel should lift up easily. If it’s hard you are missing a screw.
3. Disconnect the door locking latches and other applicable electrical cables from the door panel. The electrical cables should have male and female plugs that come apart easily.
4. There are about 8 bolts that hold the window regulator to the door and the window. Just unbolt the old regulator and replace it.
If my explanation isn’t clear enough get a chilton auto repair manual and it will have some pictures.

Posted on Nov 28, 2008

roniecon
  • 6927 Answers

SOURCE: electric window cable is unattached at on one end

you dont replace window regulator

Posted on Jul 05, 2009

  • 11 Answers

SOURCE: driver side front window does not work

replace the window regulator

Posted on Aug 18, 2009

Testimonial: "Thanks. It cost $350CF to replace the whole setup, except for the motor. It is a large aluminium stamping with all cables, pulleys etc. attached. "

raygin
  • 322 Answers

SOURCE: how do i repair the electric window mechanism on

The winder mechanism is plastic and prone to snapping. get a new lifter assembly. but keep your old winder motor as this is not included. Remove the door trim - screws in handle and pops around edge,(difficult to get door card past door handle take care) - disconnect elect plugs for speakers and door controls . then push out the plastic pin that connects the drive to the glass frame - awkward job - needs patience and care. hope this helps - good luck.

Posted on Jul 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear passenger window drivers side wont work - mitsubishi 380


hi

380 Mitsubishi's have a electric window regulator problem


front and back regulators are notorious for breaking and failing.


some times the cables also come off or the plastic components attached to the cables break


the motor turns a plastic wheel that winds the cables back and forward and this wheel jams or the cables come off the guides.


anyway the short answer is to change the whole regulator with a secondhand or a new one depending on your budget

i hope this helps


cheers

Jan 15, 2013 | Cars & Trucks

1 Answer

How to replace low beam bulb on toyota avalon XL 2009


Here's what I did to change the driver's side halogen low beam bulb #9006. Do so at your own risk.


1. First ensure fuses are OK. There are four(4) 15A fuses in the fuse box under the hood - drivers side. All are clearly mapped out on underside of fuse box cover. I used the continuity tester circuit on a VOM to ensure they were OK.

2. Remove large plastic shroud that runs across from one side of the top front under the hood of vehicle to the other side. 5 plastic pins held mine in place. Once off -- you'll be able to see your vehicles radiator cap. Removing this helps provide some additional access and leverage to better work with.

3. Remove battery negative cable - 10mm socket

4. Remove battery hold down bracket - rod - one(1) 10mm bolt at front - one(1) 10mm nut on rod. Deep socket 10mm helps with the 10mm nut.

5. Remove battery positive cable - 10mm socket

6. Remove battery and plastic battery tray

7. You should see the halogen low beam bulb #9006 in front of the fuse box(drivers side). Mine has a brown electrical plug connected to it. It helps to first remove and place out of the way - the parking light which is just to the left - the assembly for mine is light gray in color. Doing so gets that wire out of the way. One less distraction when you reach in to remove the low beam halogen bulb #9006.

8. Remove electrical connection from halogen low beam bulb #9006. There's a locking tab on the bottom - press in and while doing that - push down on the electrical connector from the top. It comes off without a great deal of effort.

9. Remove halogen low beam bulb #9006 by turning counter-clockwise - looking at the bulb from the back. Mine did not want to twist loose right away. Go slowly - take your time. It should eventually come loose. #9006 bulb came out easily even with the fuse box nearby.

10. Install new halogen low beam bulb #9006. I opted for a $10 Wal-Mart Sylvania #9006.

11. Reconnect electrical connection to the new halogen low beam bulb #9006.

12. Clean battery tray and terminals on battery + connections on battery cables.

13. Install battery tray and battery

14. Connect positive battery cable to battery - 10mm

15. Connect hold-down and rod + one(1) 10mm bolt at front and one(1) 10mm nut that goes on rod at rear.

16. Connect negative battery terminal - BUT - before doing so - have your remote locking/unlocking device handy. As soon as you connect the negative battery cable to the batteries negative terminal - the horn will sound(alarm). Quickly depress the UNLOCK button on your vehicles remote. Finish tightening the negative cable. You should also see that the low beam is once again functional as it will come on when the alarm is sounded.

17. Reinstall large plastic shroud and all lock down tabs

18. Start car and set clock/radio settings/etc.

19. There is a procedure to resync the power windows. The following provided by inov8 from another forum.

Copied from TSB PD002-05

NOTE:
Anytime the battery terminal has been disconnected, please initialize the driver's door
power
window and front passenger's door power window after reconnecting the
battery terminal.

With ignition switch in the "ON" position, do the following:

1. Push down and hold the driver's door power
window switch to completely open
the
window.
2. Pull and hold up the driver's door power
window switch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully
pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power
window switch for the passenger's door window should
be blinking.
4. Push down and hold the passenger's door power
window switch to completely open
the
window.
5. Pull and hold up the passenger's door power
window switch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully
pushing the switch briefly to the "DOWN" and "UP" positions.

Sunroof initialization is similar.


20. There is a procedure to resync power seats. Extracted from factory service doc:

Using seat switches - fully slide seat fwd. - fully recline seatback fwd. - fully raise seat cushion and head rest.

Using seat switches - fully slide the seat rearward - fully recline the seatback rearward - fully lower seat cushion and head rest.

Jun 14, 2012 | 2009 Toyota Avalon XL

1 Answer

2003 Lincoln Town Car - Power window switch removal/installation


SECTION 501-05: Interior Trim and Ornamentation 2003 Town Car Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/28/2002 Front Door Trim Panel adobe.gif Printable View (206 KB) Removal and Installation
NOTE: LH side shown, RH side similar.
  1. Disconnect the battery ground cable. For additional information, refer to Section 414-01.
  1. Remove the window switch plate.
    a0045307.gif
  1. Disconnect the electrical connectors.
    a0044981.gif
  1. ani_caut.gif CAUTION: Use care not to damage the trim panel covers.
    Open the screw covers.
    a0045817.gif
  1. Remove the screws and the assist handle.
    a0045818.gif
  1. Remove screws and the front door trim.
    a0045819.gif
  1. Disconnect the electrical connectors.
    a0045834.gif
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n306887&c35=wsm%2cfront%20door%20trim%20panel%2cs3g%2c501-05%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=modem&hp=n&[aqe]

Apr 02, 2010 | 2003 Lincoln Town Car

1 Answer

Electric window regulator for front driver side.


Your best bet is to go through your local dealership. They will have the part you need and it should be the exact one for your car.

Jul 21, 2009 | 1996 Honda Accord

1 Answer

Electric windows on drivers side won't work


...if you know how to take out the electric window switch...see the burn mark of the switch and see if the switch and the cable not broken...if it broken and had a burn mark in the switch then you have to change the switch...see also the motor inside the door trim...

Jul 07, 2009 | 1989 Peugeot 405

1 Answer

Fallen driver's side window


probably need a new window regulator. ebay. 93 to 98 should fit.

Section 01-05: Trim, Interior 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Trim Panel(s), Door Front
Removal
  1. Disconnect the battery ground cable (14301) if equipped with power locks or power windows.
  1. swv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use care when removing the front door inside handle escutcheon (22620). Failure to do so can result in damage to the component.
    Carefully pry off the front door inside handle escutcheon by inserting a standard 1/4 inch screwdriver between the top rear portion of the front door inside handle escutcheon and the front door trim panel (23942) .




  1. If equipped with manual windows, slip a clean shop rag between the window regulator handle (23342) and the front door trim panel .
  1. Pull the shop rag back and forth to release the window regulator handle clip.




  1. Remove the three cover caps and front door trim panel screws.
  1. Remove the one front door trim panel capped screws from the door pull handle.
  1. If equipped with power windows, remove the door pull handle. Disconnect the electrical connectors.
  1. Slide a flat-bladed tool behind each of the retainers and twist the tool to disengage the front door trim panel from the front door (20124) .
  1. Remove the front door trim panel.
Installation
To install, reverse the removal procedure.
---------------------------------------------------------
Window Regulator, Power Front Door
Removal
  1. Disconnect the battery ground cable (14301) .
  1. Remove the front door window glass (21410) . Refer to the front door window glass removal procedure in this section.
  1. Remove the two front door brace bolts and the front door brace.


    415712f.gif

  1. Disconnect the front window regulator electric drive electrical connector.
  1. Remove the four front door window glass regulator track bolts.

    67b6136.gif


  1. Remove the three front window regulator electric drive bolts.
  1. Remove the front door window glass regulator track and the front window regulator electric drive (23394) as an assembly through the opening in the front door (20124) .
Installation
  1. Install the front door window glass regulator track and the front window regulator electric drive as an assembly through the opening in the front door .
  1. Install the three front window regulator electric drive bolts. Tighten the front window regulator electric drive bolts securely.
  1. Install the four front door window glass regulator track bolts. Tighten the front door window glass regulator track bolts securely.

Apr 29, 2009 | 1998 Mercury Villager

1 Answer

Electric window motors


They should be the Same Motors.

Jan 23, 2009 | 2005 Nissan Xterra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

424 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6924 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...