Question about 1992 Lexus Sc 300

1 Answer

Cant change starter

No way to get to the bolts

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 137 Answers

Looked this up online, it says you may have to disconnect the fuel hose and tubes from the starter body, sounds like they get in the way of access to the bolts that hold the starter. of course you want to disconnect the battery negative terminal first, otherwise you risk causing a spark when you disconnect the starter connections, that would be especially bad if there are fuel lines right there by the starter. hope that helps

Posted on Jun 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cant get the starter off of my 2004 nissan exterra and the bolts are out how is it stuck to the engine

starter gear is probably stuck in flywheel. 1. disconnect battery 2. use correct size socket w/ratchet and turn the crankshaft on front of motor. the bolt is inside crankshaft pulley.

Dec 25, 2013 | 2004 Nissan XTerra

1 Answer

Removed two bolts from starter and cannot get starter out heard may be extra support bolts but cant locate

I had a Toyota with an odd-ball starter bolt from the back side of where the starter mounted. It didn't even look like a starter bolt, but sure enough, it was. So keep checking, you may have a third bolt you haven't found.

Aug 22, 2013 | 1997 Mitsubishi Diamante

1 Answer

Just need the instructions on how to change the starter on a 1998 GMC 1500 with a 4.3.

start by diconnecting the negative battery terminal, Locate the starter under the truck, should be 2 bolts verticaly though the starter. Loosen both of the bolts but do not remove them. On top of the starter their should be a large and a small wire connected disconnect both of them ( if u cant reach or see them remove the starter by taking out the 2 verticle bolts then remover wires) once bolts and wires are off the starter just wiggle it into postion and remove between the motor/ exausht and frame. Try to remember how it comes out will make it simpler to fit going back in. if thier isnt enough clearence u may have to notch the frame or loosen the motor mounts and raise the engine slight with a floor jack.,

Jan 31, 2011 | GMC C1500 Cars & Trucks

1 Answer

Trying to change a stater cant find the bolts on top

the top bolts come in from the rear of the bell housing. They these bolts mount both the bell housing to the block and the starter motor to the block. Under neath just line up wich mount bolts are close to the starter and undo them, possibly 2 that hold them. once remove starter should fall straight into your hand

Jan 22, 2011 | 1997 Ford Expedition

1 Answer

Need to change the starter and cant get to the second bolt ....... dont know what to do next need some help

Kind of hard to explain with words. Try this, deep socket- 6 in.extension- ratchet. Put it next to starter (as if taking out the first bolt), then slide it up and over the starter. Sometimes you can't come in from the back.

Oct 20, 2010 | 1997 Ford Thunderbird LX

1 Answer

Top starter bolt rounded off cant get out?

can you cut grove on the bolt head with a dremmil or a small cutting tool? Maybe a hacksaw?

Mar 07, 2010 | 1998 Mercury Mountaineer

1 Answer

Fiat punto gearbox

theirs another bolt coming into the starter from the other side

Jul 30, 2009 | 2006 Fiat Strada

1 Answer

Starter 99 s10

First disconnect the positive battery cable. You already have the bolts out. pull the starter back and down and it will drop out. do not let it hand from the wires. Disconnect the wires to the starter. Pay attention as to which wire comes off what terminal. They must be attached correctly or your starter will not crank after installation. Then the last thing you do will be to hook the battery up again.

Jan 21, 2009 | 1999 Chevrolet S-10 Pickup

2 Answers


you have two bolts on your starter take the two bolts out and take the wire off the strater

Jun 11, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts


Level 3 Expert

81294 Answers


Level 3 Expert

918 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides