Question about 2000 GMC Sierra

2 Answers

Keyless entry remote quit working. Just purchased new battery. Now Spare remote does not work either.

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 15 Answers

Transmitter Programming Notes Transmitter Programming

  1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
  2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
  3. Repeat step #2 for each additional keyless entry transmitter.
  4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

Posted on Jun 17, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

I had the same problem. Go to www.keylessfix.com Fixed the problem in seconds!

Posted on Dec 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 HHR Remote Starter not working


Is this an issue with all 2008 HHR remotes??? Highly doubtful , probably the vehicles keyless entry system . Taking the vehicle to a qualified repair shop an having the keyless entry system checked for DTC'S - diagnostic trouble code's . Do you know what a DTC is ?
The keyless entry system is a vehicle entry device. The keyless entry system is used in conjunction with the body control module (BCM) to remotely activate certain vehicle features. Keyless entry will lock/unlock the doors, or release the rear compartment lid when a corresponding button on the keyless entry transmitter is pressed. This is accomplished by the transmitter sending a radio frequency to the remote control door lock receiver (RCDLR). The RCDLR interprets the signal and activates the requested function via a serial data message to the BCM. A low transmitter or vehicle battery or radio frequency (RF) interference from aftermarket devices, such as 2-way radios, power inverters, computers, etc., may cause a system malfunction. High RF traffic areas may also cause interference that could lead to a malfunction. Keyless entry allows you to operate the following components:
• Door locks
• Liftgate lock
• Remote rear doors (Panel only)
• Vehicle locator/panic alarm
• Illuminated entry lamps
• Remote vehicle start
The keyless entry system has the following components:
• Keyless entry transmitters
• Keyless entry antenna
• 2 Way Advanced Remote Start RCDLR
• BCM

Guessing will not fix this .

Jan 12, 2018 | 2006 Chevrolet HHR

1 Answer

Keyless remotes not working


Try reprogramming the remotes. Here are the instructions for the procedure. Hope it helps. Cobra!
Programming NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the RAP module, perform the following steps:
  1. Make sure that the anti-theft system is not armed or triggered.
  1. Turn the ignition switch (11572) from OFF to RUN eight times within ten seconds, ending in RUN. If the RAP module has successfully entered program mode, it will lock and then unlock all doors.
  1. Within 20 seconds, press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed. Repeat this step for each transmitter.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait several seconds and press the button again. If the door locks still fail to respond, refer to Inspection and Verification.
  1. Turn the ignition switch to the OFF position, or wait up to 20 seconds after step 2, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the RAP module will lock and unlock all doors one last time to confirm.

Jun 06, 2010 | 1998 Ford F150 Regular Cab

1 Answer

2007 gmc yukon. Keyless Entry problem. The remote quit working but the gmc place said its not the battery. Help


Disconnect the battery to the car for five mins. Thay should reset the keyless module. I had the same problem

May 20, 2010 | Cars & Trucks

1 Answer

My doors wont unlock or lock with the remote keyless entry on both keys. one set of keys being the spare and never used it cant be the battery in the remote?


could be, try installing a new battery on the spare remote and retry,if it still doesnt work, then reprograming will be needed, try the battery first and let me know what happens.

Feb 26, 2010 | 2006 Suzuki Swift

1 Answer

Keyless entry not working. 2010 equinox


reset itself. may have been something obstructing rear gate from closing all the way.

Sep 30, 2009 | 2009 Chevrolet Equinox

2 Answers

Keyless entry for my 07 Chevy Impala works on and Off


my 2006 impala keyless remote dont work i change the battery still the same problem the spare remote same problem how to solve this problem

Jul 21, 2009 | 2007 Chevrolet Impala LS Sedan New Cars

2 Answers

Purchased used. have remote for keyless remote.


That you need to take it to a car stereo dealer that install NEW keyless entry's...Sorry, thats the easiest way to fix this issue.

Jun 14, 2009 | 1999 GMC Jimmy

1 Answer

How do i program remote keyless entry? I replaced the battery and keyless entry quit working,


You don't normally program a keyless entry, that's done for you by the technicians that install that. If the replaced battery doesn't solve the problem, take the battery and the remote to the techies that installed it.

Mar 27, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

Both of my keyless entry remotes just stopped working any ideas


sometimes you have to hold the lock and unlock at the same time and stand close to your jeep until the locks unlock and lock agian if that works then they are reset if not than try to change the batterys in one remote and retry

Mar 11, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Lincoln LS keyless entry problem


you half to take it to a ford dealer and have the remote reprogramed to the car.

Feb 16, 2009 | 2001 Lincoln LS

Not finding what you are looking for?
2000 GMC Sierra Logo

1,756 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...