Question about 2007 Nissan Frontier SE Crew Cab

1 Answer

Can i run tires on a 08 titan without tire pressure sensors? I have two sets of wheels and rims and dont want to switch sensors will it do any harm or just turn a lite on?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Nissan Master
  • 3,854 Answers

No harm, your light will just stay on.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

6 Answers

Yellow horseshoe shape with explanation flashing on my dash of Nissan Titan


That signal is from your tire monitoring sensors, telling you that there is air pressure difference between tires. The tire pressure should be same in all tires.

Jan 09, 2013 | Cars & Trucks

1 Answer

My tire pressure symbol thats pops up but my tires are good


tire monitor system has a sensor in each rim. damage to these senors, or replacement of compete rim and wheels without reinstallation of sensors will cause light to come on. if nothing was changed, possible long life battery in tire senors is bad.

Dec 15, 2012 | 2008 Volkswagen Jetta

1 Answer

How do you clear "check


1. inflate your tires to the correct pressure (not just visually, but use a gauge)
2. your wheels have TPMS (tire pressure monitoring system) sensor attached to the rim on the filler stem, inside the tire. if that sensor has gone bad, your dash will register as having low tire pressure. replace that TPMS (little black box in the wheel. you have to remove the tire to get to it). If you have aftermarket wheels, you need to transfer the TPMS sensor from the stock wheel to the new wheel.

Mar 02, 2011 | 2002 Buick LeSabre

3 Answers

How do i take the wheel sensors off of a 2007 ford five hundred?


Hi, if you are referring to the tire pressure sensors they are actually the valve stems that you put air into the tire with, the sensor is inside the tire and it is not able to be taken out without taking the tire off of the rim and removing the sensor and installing a standard valve stem. But if you remove the sensor your little tire warning light will stay on. Good luck

Dec 09, 2010 | 2007 Ford Five Hundred Limited Sedan

4 Answers

My tire pressure monitor keeps going off even when tires are checked. What might be the problem?


for one have u checked the spare tire as well other than that bad sensor

Dec 05, 2010 | 2002 BMW 7 Series

2 Answers

I also have a 2005 jeep liberty with the same light on top left corner. horse-shoe with and exclamation in it.


That is the tire pressure sensor light. It will come on if one or more of the tires are over-inflated or under-inflated. It will also come on if there is a signal problem with one or more of the sensors.

Oct 18, 2009 | 2005 Jeep Liberty

2 Answers

I have put custom rims on my 2008 grand prix and it gives me the check tire pressure reading on every start up. How do I disconnect this feature?


Not disconnectable. This is a mandated feature for 08 and up cars in the US, thanks to the Firestone Wilderness AT fiasco. There's sensors in the wheels that came with the car, they should be installed into your new wheels.

Oct 01, 2009 | 1997 Pontiac Grand Prix

3 Answers

How do i reset the tpms on a 08 implala SS after a tire rotation,without a owners manual


You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.
The TPMS sensor matching process is outlined below:
  1. Set the parking brake.
  2. Turn the ignition switch to ON/RUN with the engine off.
  3. Press the Remote Keyless Entry (RKE) transmitter's lock and unlock buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.
  4. Start with the driver side front tire.
  5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position.
  6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
  7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
  8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
  9. Turn the ignition switch to LOCK/OFF.
  10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
  11. Put the valve caps back on the valve stems.

Aug 31, 2009 | 2008 Chevrolet Impala

2 Answers

How to reset the tire pressure on a 08' chevy tahoe?


TPMS Sensor Matching Procedure

Each TPMS sensor has a unique identification code. Any time you rotate your vehicle's tires or replace one or more of the TPMS sensors, the identification codes will need to be matched to the new tire/wheel position. The sensors are matched to the tire/wheel positions in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear tire using a TPMS diagnostic tool. See your dealer/retailer for service.

The TPMS sensors can also be matched to each tire/wheel position by increasing or decreasing the tire's air pressure. If increasing the tire's air pressure, do not exceed the maximum inflation pressure indicated on the tire's sidewall.

To decrease air-pressure out of a tire you can use the pointed end of the valve cap, a pencil-style air pressure gage, or a key.

You have two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer than two minutes, to match the first tire and wheel, or more than five minutes to match all four tire and wheel positions the matching process stops and you need to start over.

The TPMS sensor matching process is outlined below:

  1. Set the parking brake.
  2. Turn the ignition switch to ON/RUN with the engine off.
  3. Press the Remote Keyless Entry (RKE) transmitter's LOCK and UNLOCK buttons at the same time for approximately five seconds. The horn sounds twice to signal the receiver is in relearn mode and TIRE LEARNING ACTIVE message displays on the DIC screen.
  4. Start with the driver side front tire.
  5. Remove the valve cap from the valve cap stem. Activate the TPMS sensor by increasing or decreasing the tire's air pressure for five seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds to sound, confirms that the sensor identification code has been matched to this tire and wheel position.
  6. Proceed to the passenger side front tire, and repeat the procedure in Step 5.
  7. Proceed to the passenger side rear tire, and repeat the procedure in Step 5.
  8. Proceed to the driver side rear tire, and repeat the procedure in Step 5. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.
  9. Turn the ignition switch to LOCK/OFF.
  10. Set all four tires to the recommended air pressure level as indicated on the Tire and Loading Information label.
  11. Put the valve caps back on the valve stems.

Jul 28, 2009 | 2008 Chevrolet Tahoe

1 Answer

Is tpms sensor needed when replacing tires?


Without the sensors, the lights will continue to warn you your pressure is low. No harm will come from this to your vehicle. It is a safety system to warn you about the tire pressure so you will take immediate action. The manufacturer is ramping up to meet requirements for future safety regulations.

Feb 18, 2009 | 2005 Honda Pilot

Not finding what you are looking for?
2007 Nissan Frontier SE Crew Cab Logo

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...