Question about 2000 Pontiac Grand Prix

1 Answer

Remote wont work

I changed the battery in the remote and it still wont lock and unlock,do you have to reset it?

Posted by on

  • Anonymous Mar 30, 2014

    remote door lock wont work,change battery in it,still nothing

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Pontiac Master
  • 3,854 Answers

GRAND PRIX KEY FOB PROGRAMMING INSTRUCTIONS 
Important 
Once the Keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver. 

Perform the following steps:
Sit in the vehicle driver's seat. (actually it’s much eazy er from the front pass seat) 
Remove the ignition key from the ignition lock cylinder. 
Close all of the vehicle's doors. 
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis. 
Turn the ignition lock cylinder to the ACC position. 
Turn the ignition lock cylinder OFF, then back to ACC within 1 second. 
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important 
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.

Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds. 
Repeat step 8 in order to program each additional transmitter. 
Remove the ignition key from the ignition lock cylinder. 
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis. 
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation.

Good luck and hope this helps. 

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My remote wont UNLOCK and someone suggested I should reset the remote, Thanks for the tip but How do I reset my remote after I change the batteries


press and hold the lock button for 5 seconds then the vehicle should give off 3-5 flashes on indicaters then try the unlock button , if this doesnt work i would say the fob isn't transmitting and needs to be inspected for a fault

Apr 28, 2014 | 2002 Jeep Grand Cherokee

1 Answer

I need to know how to reset my remote so i can use


Hold down the the lock and unlock buttons on the remote while by the vehicle for about 10 seconds this should reset the key fob.The locks may cycle but should correct the issue.

May 13, 2010 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

VW car key wont work


lock the car with key and hold it over for 30 secs,then,hold unlock button down on remote for 30 secs ,this should reset system....

Mar 24, 2010 | Volkswagen Fox Cars & Trucks

2 Answers

Remote wont unlock my passenger door and wont bib when you hit butten


the locking mecanisim in the door needs replacing goodluck can be tricky

Mar 19, 2010 | 2003 Honda Pilot

1 Answer

Key wont' remotely lock/unlock (new batteries)


place key in ignition turn ignition to run position
hit the butons on remote it should re prog the remote
if remote got wet or dirty open up remote and clean contacts

Jan 22, 2010 | 2003 Audi A6

1 Answer

Both of my keyless entry remotes just stopped working any ideas


sometimes you have to hold the lock and unlock at the same time and stand close to your jeep until the locks unlock and lock agian if that works then they are reset if not than try to change the batterys in one remote and retry

Mar 11, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Change battery on 99 galant


usually all you need to do is hold the lock and unlock buttons at the same time for about 8-10 seconds will pointing at the car.

Feb 02, 2009 | 1999 Mitsubishi Galant

1 Answer

Lock/unlock doors


Does the second remote work?  Have you changed the battery and then done any reset required by the manual?  Ten year old batteries are probably shot.

Aug 26, 2008 | 1998 Chevrolet Corvette

Not finding what you are looking for?
2000 Pontiac Grand Prix Logo

661 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...