Question about 2001 Pontiac Aztek

1 Answer

How do you replace a water pump in an aztec? - 2001 Pontiac Aztek

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 15 Answers

Notes Water Pump Replacement

Removal Procedure
How do you replace a water pump in an aztec? - 3e77de9.gif

  1. Drain the cooling system until the coolant is below the level of the water pump.
  2. Remove the drive belt guard.
  3. Loosen the water pump pulley bolts.
  4. Remove the drive belt.


c7273fb.gif
  1. Remove the water pump pulley bolts.
  2. Remove thHow do you replace a water pump in an aztec? - c102468.gifp pulley.
c102468.gif
  1. Remove the water pump bolts.
  2. Remove the water pump.
  3. Remove the water pump gasket.
  4. Clean the water pump mating surfaces
Installation Procedure
  1. Install the water pump gasket.
  2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
  3. Install the water pump bolts.
    • Tighten the bolts to 10 Nm (89 inch lbs.) .
f16e1fd.gif
  1. Install the water pump pulley. Loosely install the mounting bolts.
  2. Install the drive belt.
  3. Install the water pump pulley bolts.
  • Tighten the bolts to 25 Nm (18 inch lbs.) .
  • 258f600.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks

    Posted on Jun 17, 2009

    Ad

    2 Suggested Answers

    6ya6ya
    • 2 Answers

    SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

    Hi,
    a 6ya expert can help you resolve that issue over the phone in a minute or two.
    best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
    the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
    click here to download the app (for users in the US for now) and get all the help you need.
    goodluck!

    Posted on Jan 02, 2017

    Ad
    • 430 Answers

    SOURCE: How long does it take to replace a water pump on

    It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
    Removal Procedure :
    techmecho.gif

    1. Drain the cooling system until the coolant is below the level of the water pump.
    2. Remove the drive belt guard.
    3. Loosen the water pump pulley bolts.
    4. Remove the drive belt.
    techmecho_0.gif
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    techmecho_1.gif
    1. Remove the water pump bolts.
    2. Remove the water pump.
    3. Remove the water pump gasket.
    4. Clean the water pump mating surfaces
    Installation Procedure
    1. Install the water pump gasket.
    2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
    3. Install the water pump bolts.
      • Tighten the bolts to 10 Nm (89 inch lbs.) .
    techmecho_2.gif
    1. Install the water pump pulley. Loosely install the mounting bolts.
    2. Install the drive belt.
    3. Install the water pump pulley bolts.
      • Tighten the bolts to 25 Nm (18 inch lbs.) .
    techmecho_3.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks.
    4. That's it.

    Posted on Nov 18, 2010

    Add Your Answer

    Uploading: 0%

    my-video-file.mp4

    Complete. Click "Add" to insert your video. Add

    ×

    Loading...
    Loading...

    Related Questions:

    1 Answer

    How do the power steering hoses go on on a 2001 Pontiac Aztek and why is there no circular motion inside the pump


    The only squared thing on the pump is the "plastic"
    fluid tank... Everything else about the design & function
    is "circular".

    There is ABSOLUTELY circular "MOTION" inside the PUMP...
    PLEASE NOTE... there is a giant pulley on the front..
    and the design of the pump is all about rotational force of the hydraulic pump (right THROUGH the middle).

    High pressure to the high pressure...
    (with a possible cooler option in the middle)
    Low pressure back to the reservoir

    See images at: 2001 aztek power steering lines Bing images

    https://www.bing.com/images/search?q=2001+aztek+power+steering+lines&qpvt=2001+aztec+power+steering+lines&qpvt=2001+aztec+power+steering+lines&qpvt=2001+aztec+power+steering+lines&FORM=IGRE

    (at the very bottom)

    Optional cooler:
    More Information for FOUR SEASONS 53019

    Return
    More Information for DNJ ENGINE COMPONENTS PSP1099

    More Information for ACDELCO 36365861

    More Information for GATES 365861

    Pressure line (62 inches)
    More Information for ACDELCO 36365406


    Power Steering Pump Reservoir A1 CARDONE Reman 2001

    2001 aztek power steering lines Bing images

    Jun 08, 2016 | 2001 Pontiac Aztek

    1 Answer

    I just bought a 2004 Aztec and the floor is soaking wet on drivers side, it has not dried in a week.


    a bad door seal perhaps . if it has a sunroof that could also be where the water got it at .

    Jul 17, 2015 | 2004 Pontiac Aztek

    1 Answer

    How do I replace the fuel pump on an 01 Pontiac Aztec?


    Not easy. Fuel pump is inside gas tank. Some cars have a panel in the floor above the gas tank to allow access, but I think yours does not. If not, you must drop the tank.

    Feb 26, 2015 | Pontiac Cars & Trucks

    2 Answers

    2001 aztec, new thermostat...over heats in winter, and when speed reduced blows cold air. Plenty of antifreeze. Any ideas what could be wrong?


    YOU HAVE TO BLEED THE LINES THE ARE TWO NIPPLES ONE BY THE THERMOSTAT AND ONE BY THE WATER PUMP. YOU HAVE AIR IN THE LINES THE AIR BUBBLES BUILD UP IN FRONT OF THE THERMOSTAT AND PREVENT IT FROM ORENING ANY TIME YOU OPEN THE RADIATOR CAP OR ANYTHIN YOU MUST BLRRD THEM LINES YOU MIGHT HAVE TO DO IT A COUPLE TIMES BUT A RELATIVELY EASY FIX

    Dec 26, 2011 | 2002 Pontiac Aztek

    1 Answer

    We have replaced the transmission, bypassed the heater but the aztec is still over heating and running into the over flow what else could we check


    i assume by transmission you mean thermostat.the other things that can cause over heating is the cooling fan for the rad may not be working(you don`t say),the coolant flow through the rad may be poor,the water pump impeller may be worn to the point that it can`t circulate coolant properly or you have a head gasket problem which you can get a block test done on the car to eliminate it.

    May 05, 2011 | 2001 Pontiac Aztek

    1 Answer

    How long does it take to replace a water pump on Pontiac Aztec?


    It takes near to 1.5 hours to replace the water pump on Pontiac Aztec. The procedure to replace the water pump is as follows:--- Water Pump Replacement ---------
    Removal Procedure :
    techmecho.gif
    1. Drain the cooling system until the coolant is below the level of the water pump.
    2. Remove the drive belt guard.
    3. Loosen the water pump pulley bolts.
    4. Remove the drive belt.
    techmecho_0.gif
    1. Remove the water pump pulley bolts.
    2. Remove the water pump pulley.
    techmecho_1.gif
    1. Remove the water pump bolts.
    2. Remove the water pump.
    3. Remove the water pump gasket.
    4. Clean the water pump mating surfaces
    Installation Procedure
    1. Install the water pump gasket.
    2. Install the water pump. Notice: Refer to Fastener Notice in Service Precautions.
    3. Install the water pump bolts.
      • Tighten the bolts to 10 Nm (89 inch lbs.) .
    techmecho_2.gif
    1. Install the water pump pulley. Loosely install the mounting bolts.
    2. Install the drive belt.
    3. Install the water pump pulley bolts.
      • Tighten the bolts to 25 Nm (18 inch lbs.) .
    techmecho_3.gif
    1. Install the drive belt guard.
    2. Fill the cooling system.
    3. Inspect the cooling system for leaks.
    4. That's it.

    Nov 18, 2010 | 2001 Pontiac Aztek

    1 Answer

    My 2002 Aztec lost all it's anti-freeze I noticed that the back left was wet, and found no blown hoses in the front. does this indicate a blown water pump and if so how do I replace it


    It could be a split in the radiator or the pump leaking or a blown head gasket would also pump water out of the radiator. Refill it with water and run the engine with the radiator cap off. If there is a dribble coming from the pump it needs to be replaced. If a large amount of bubbles come from the radiator, and blow water all over the place, suspect a blown head gasket.

    Mar 05, 2010 | Pontiac Aztek Cars & Trucks

    2 Answers

    Do I need any special tools? How Hard is it?water pump 2002 aztek


    take everything around your water pump of and use a metric 10 box end wrench

    Apr 30, 2009 | 2002 Pontiac Aztek

    Not finding what you are looking for?
    2001 Pontiac Aztek Logo

    5,502 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...