Question about 2005 Chevrolet Aveo
Most probable cause is shift interlock solenoid,generally located on shifter assebly,requires removal of console.Then will be electric solenoid located at lower part of shifter.May also be brk switch at pedal.
Posted on Jun 17, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Car Won't Fully Shift into Park
You either have problem with the shifter assy, or the shifter cable has come out of adjustment.
If you remove the shifter bezel and center console you will be able to see the shifter cable. There will be a white or black lift tab on the cable. Release the tab and and place shifter in park. If it still does not go into park that means that you will need a shifter assy. If it goes into park with the tab released you push the tab back down with it still in park.
That should take care of your problem.
Posted on Aug 29, 2008
SOURCE: key gets stuck in ignition
My daughter drives a Suzuki, my solution to her is: while the gear shift lever is in park, lightly put pressure on the gear shift lever, through the park position and while pressing the gear shift towards park light rock left to right while trying to remove the key.
The interlock between the transmission and the ignition switch needs to be adjusted/ repaired or replaced.
Posted on Oct 16, 2008
This is not a permanent fix, but you'll be able to shift and drive...this is a "safety feature" when you're break lights aren't working...it may be a fuse issue, i found that didn't help either.
How to drive it while it's "broken" On the top left of your gear shift is circle that looks like a button that is only 3/4 there...see picture (it's circled in red)
pry that off with a key or something... now restart your car, push on the break and at the same time insert a key or something into the now open hole...while pushing down use the other key to shift into reverse. You will need to do the same thing to shift back into park.
Good heavens that is the most inneficient safety feature I've ever heard of. How about instead of leaving the car immoble and keeping you in a scetchy neihborhood to get mugged they just "invent" a warning light notification. grr
Posted on May 04, 2009
Inside the center console, on the side of the shifter, there is a neutral safety switch. You can replace it, or remove it. If you remove it, you will always be able to shift the gear, even with the car off, so its something to think about. But it can be done.
Posted on Oct 17, 2009
this is for newer malibu's, but may work for you too.
#08-05-22-009: Intermittently Brake Lights (Stop Lamp) Do Not Function Correctly, Extended Travel to Shift Out of Park, Cruise Control Inoperative, DTC C0161/C0277 Set (Perform Repair as Outlined) - (Dec 4, 2008)
Subject: Intermittently Brake Lights (Stop Lamp) Do Not Function Correctly, Extended Travel to Shift Out of Park, Cruise Control Inoperative, DTCs C0161/C0277 Set (Perform Repair as Outlined)
Models: 2004-2007 Chevrolet Malibu, Malibu Maxx
2008 Chevrolet Malibu Classic
2005-2009 Pontiac G6
2007-2009 Saturn AURA
Some customers may comment that intermittently the brake lights do not function correctly. Other symptoms may include extended pedal travel required to shift out of PARK, cruise control does not function correctly, and DTC C0161 and/or C0277 may be set.
The most likely cause of this condition is high resistance due to terminal fretting corrosion in the body control module (BCM) C2 connector (specifically pins C2-18, C2-31 and C2-59).
DO NOT replace the BCM for this condition. Disconnecting the C2 connector, adding dielectric silicone grease and reconnecting the C2 connector per the procedure below will correct the high resistance condition due to terminal fretting corrosion.
Remove the right side front floor console side trim panel to access to the Body Control Module (BCM).
Locate the C2 connector on the BCM.
Unlatch the C2 connector and disconnect the C2 connector from the BCM.
Reconnect the C2 connector back on the BCM and re-latch.
Repeat Steps 3 and 4 (this step cleans up the terminal fretting corrosion).
Using the Tech 2®, verify the brake pedal position sensor (BPPS) voltage is between:
• 0.88V - 2.11V (for 2004-2006 model years)
• 0.73V - 1.47V (for 2007-2009 model years)
Check for proper operation of the brake lights.
• If the brakes lights are operating properly, remove the C2 connector again from the BCM and proceed to Step 8.
• If the brake lights are not operating properly, proceed to Step 12.
Apply dielectric lubricant (clear gel) GM P/N 12377900 (In Canada, use P/N 10953529) on the BCM C2 pins (apply with a one-inch nylon bristle brush) on all the C2 connector pins (this will treat the pins against fretting corrosion).
Reconnect the C2 connector back on the BCM and re-latch.
Reinstall the right side front floor console side trim panel.
Using the Tech 2®, check that the BPPS ratio is equal to BPPS learned home when the brake pedal is not depressed.
• If they are equal, brake lamps should be operating correctly and no further steps are necessary.
• If they are not equal, perform the Brake Pedal Position Sensor Calibration procedure in SI to complete the repair.
Check the brake lights for proper operation. If incorrect, refer to SI and perform normal diagnostics. Source(s): gm tech
Posted on Oct 23, 2009
Tips for a great answer:
Oct 21, 2015 | 2008 Chevrolet Chevrolet TrailBlazer LT
Aug 19, 2015 | Cars & Trucks
Oct 15, 2014 | 2013 Subaru Outback
Jun 16, 2014 | 2004 Toyota Solara
Dec 22, 2013 | 2008 Honda Civic
Jun 17, 2013 | 1994 Chevrolet Lumina APV
Sep 16, 2011 | Jeep Grand Cherokee Cars & Trucks
Mar 27, 2010 | 2000 Daewoo Leganza
Oct 04, 2008 | 2006 Suzuki Forenza
Jul 15, 2008 | 1996 Honda Accord
1,346 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: