Question about 2000 Ford Windstar

1 Answer

Lower radiator hose connecting tube to water pump. how do i remove and replace old metal tube 2000 ford windstar

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,600 Answers

Remove the radiator hose remove the two bolts that hold the tube on and buy new tube and replace is in reverse order.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Waterpump 2002 ford turaus 3.0 durtec


3.0L Engine

VIN S Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
  • Splash shield
  • Lower heater hose
  • Radiator lower tube bolt
  • Radiator upper front tube bolt
  • Air cleaner assembly
  • Battery and tray
  • Water pump belt
  • Upper radiator hose
  • Engine vent hose
  • Transaxle 10 pin connector
  • Radiator bypass hose assembly
  • Thermostat housing
  • A/C compressor brace, if equipped
  • Water pump mounting nuts
  • Connector hose
  • Water pump




25996402-nto4xxgg4h3g52i5qee3bm1e-1-0.gif
To install:
  1. Install or connect the following:
  • Water pump
  • Connector hose
  • Water pump mounting nuts and tighten them to 15-22 ft. lbs. (20-30 Nm)
  • A/C compressor brace, if equipped, and tighten the nuts to 15-22 ft. lbs. (20-30 Nm)
  • Thermostat housing
  • Radiator bypass hose assembly
  • Transaxle 10 pin connector
  • Engine vent hose
  • Upper radiator hose
  • Water pump belt
  • Battery and tray
  • Air cleaner assembly
  • Radiator upper front tube bolt
  • Radiator lower tube bolt
  • Lower heater hose
  • Splash shield
2. Fill the cooling system.
3. Start the engine and check for leaks.

Dec 06, 2015 | 2002 Ford Taurus

1 Answer

Metal pipe on water pump will not stop leaking.new water pump and new metal pipe


Did you replace old rubber O ring before reinstalling tube back in position ?

Mar 14, 2014 | 2000 Ford Windstar

1 Answer

Lower radiator hose inlet tube leaks


the tube runs under the intake if it is a 3.0 liter. so the first step is to remove the intake. you may also have to remove the timing belt and water pump since the tube attaches to the rear of the water pump.

May 26, 2012 | 1997 Plymouth Voyager

1 Answer

How to replace water pump of 1976 ford e-250


Hello, follow this steps to replace the water pump:

1. Disconnect the negative battery cable,using a screwdriver to unscrew the clamp that secures the cable to the negative (-) post. Pull the cable away from the battery post.
2. Use a jack to elevate the Ford Taurus and use jack stands to shore up the jack. Alternately, you can use tire ramps.

3. Discharge the pressure in the radiator by unscrewing the cap. Remove the drain plug located underneath the radiator. Catch the coolant in a resealable container. Clean up any spills.

4. Disconnect or remove the parts in front of the water pump, using an adjustable wrench. In order, this includes the right inner splash shield, lower heater hose, upper and lower tube bolts from radiator, air cleaner assembly, battery and battery tray, water pump belt, upper radiator hose, engine vent hose, trans axle 10-pin connector, radiator bypass hose and thermostat housing.

5. Remove the water pump mounting nuts and connector hose. Unbolt the water pump from the mount. Clean off the mounting area with a shop rag.

INSTALLING THE NEW WATER PUMP:

1. Inspect the new water pump to ensure it's identical to the old pump and free of any metal splinters or debris.

2. Arrange the new gasket onto the water pump. Place a bead of high temperature automotive sealant around the area where you removed the old pump and hold the gasket in place on the new water pump as you mount the entire assembly on top of the sealant.

3. Place the new nuts into the holes in the Ford Taurus' water pump in any order for the S-type engine and in a cross configuration on the U-type engine. Using a torque wrench while the sealant is still wet to obtain a better hold, tighten to 15 foot pounds of torque.

4. Reassemble the other engine parts in the order they came off the Ford using an adjustable wrench. Replace worn parts with new ones, as needed.

5. Replace the drain plug and refill the radiator with the amount and type of coolant specified in your owner's manual. Remove the jack stands and release the jack or drive the ford off the tire ramps.

6. Attach the negative battery cable to the post and tighten the screw on the clamp. Start the engine and check for leaks. Then, close the hood

Thanks










































Jul 28, 2010 | Ford E-250 Cars & Trucks

1 Answer

Replacing a water pump on a ford windstar how do i do it?


Removal

1. Disconnect the battery ground cable.

2. Drain the cooling system. For additional information.

3. Remove the accessory drive belt.

4. Raise and support the vehicle.

5. Disconnect lower radiator hose from the water pump lower tube.

6. Remove the engine mount nuts.

Lower the vehicle.

7. Remove the cowl extension panel. (Thats theone with the wiper arms go through).

8. Disconnect the water bypass hose and the heater hose from the water pump outlet tube.

9. Remove the water pump outlet tube bolt and position the tube assembly out of the way.

10. Install the lifting eye to the exhaust manifold.

11. Attach engine lifting equipment and raise the engine 127 mm (5 inches).

12. Remove the bolt and the accessory belt idler pulley.

13. Remove the bolts and the generator support bracket.

14. Remove the four bolts and the water pump pulley.

15. Remove the water pump. Remove the five nuts. Remove the five studs.
Remove the four bolts. Remove the water pump, lower tube and gasket as an assembly.

Feb 22, 2010 | 2002 Ford Windstar Cargo

1 Answer

Leaking water from metal tube going down front of motor . what is this metal tube for


Thee tube that you are referring to is the tube that connects the radiator via a radiator hose. Assuming that the radiator hose that you have is the black one that feels like thick cloth. You might have a loose connection on the hose and the metal tube.

Jun 04, 2009 | 2000 Ford Escort

1 Answer

Removal and installation of the water pump


3.0L or 3.8L engine?

please rate as fixed if this solves your issue.

Section 03-01B: Engine, 3.8L 1996 Windstar Workshop Manual
IN-VEHICLE SERVICE Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
  1. Drain engine cooling system. Refer to Section 03-03 .
  1. Loosen drive belt tensioner (6B209) and remove drive belt (8620). Refer to Section 03-05 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Disconnect lower radiator hose (8286) from radiator lower hose tube (8291) and radiator (8005).
  1. Disconnect radiator lower hose tube from water pump (8501).
  1. Remove lower nut on both front engine support insulators (6038).
  1. Lower vehicle.
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove generator (GEN) (10346) from power steering pump support (3C511).
  1. Position drain pan and disconnect power steering pressure line from power steering pump (3A674) using Fuel Line Disconnect Tool Set T90T-9550-S.
  1. Remove power steering reservoir filler cap.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces.
    Disconnect water bypass hose (8597) and oil cooler hose (6B850) from heater water outlet tube (18663).
  1. Remove retaining bolts and disconnect heater water outlet tube from water pump.
  1. Remove A/C bracket brace.
  1. Attach engine lifting eye to left-hand (front) exhaust manifold (9430).
  1. Attach lifting equipment to engine lifting eye and raise front of engine approximately 51 mm (2.0 inches) to provide necessary clearance for water pump removal.
  1. Remove water pump pulley retaining bolts and water pump pulley (8509).
  1. Remove drive belt tensioner pulley retaining bolt and drive belt tensioner pulley (6B217) from power steering pump support.
  1. Remove power steering pump support retaining bolts and nut. Place power steering pump and support assembly aside in a position to prevent fluid leakage.
  1. Remove water pump retaining bolts and nuts and water pump. Discard used water pump housing gasket (8507).
Installation
  1. NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant.

    Clean gasket surfaces on water pump and engine front cover (6019).
  1. NOTE: The threads of the No. 1 engine front cover retaining stud must be coated with Pipe Sealant with Teflon® D8AZ-19554-A or equivalent meeting Ford specification WSK-M2G350-A2 before installing.

    NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the water pump housing gasket in position.

    Position a new water pump housing gasket on water pump housing sealing surface.
  1. Position water pump on the engine front cover. Install retaining bolts.
  1. Position power steering pump support and install retaining nuts and bolts. Tighten bolts and nuts to 40-55 Nm (30-40 lb-ft).
  1. Install drive belt tensioner pulley and retaining bolt. Tighten bolt to 70-95 Nm (52-70 lb-ft).
  1. Install A/C bracket brace.
  1. Position water pump pulley on water pump hub and install retaining bolts. Tighten bolts to 8.0-11.5 Nm (71-101 lb-in).
  1. Lower engine and disconnect lifting equipment from lifting eye.
  1. Remove lifting eye from exhaust manifold.
  1. Connect heater water outlet tube to water pump and install retaining bolts. Tighten bolts to 8-11.5 Nm (71-101 lb-in).
  1. Connect water bypass hose and oil cooler hose to heater water outlet tube. Tighten clamps securely.
  1. Connect power steering pressure line to power steering pump fitting.
  1. Install power steering reservoir filler cap.
  1. Install generator to power steering pump support. Refer to Section 14-02 .
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Install lower nut on front engine support insulators and tighten retaining nut to 88-119 Nm (65-87 lb-ft). Install lower nut of rear engine support insulator and tighten to 77-104 Nm (56-76 lb-ft).
  1. Connect radiator lower hose tube to water pump. Install retaining bolt and tighten securely.
  1. Connect lower radiator hose to radiator lower hose tube and radiator. Position hose clamps securely. Refer to Section 03-03 .
  1. Lower vehicle.
  1. Position drive belt over drive belt tensioner and release drive belt tensioner. Refer to Section 03-05 .
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: This engine has aluminum cylinder heads (6049) and requires a special corrosion inhibiting coolant to avoid cooling system damage. Refer to Section 03-03 for the coolant specifications.
    Fill and bleed cooling system with specified coolant.
  1. Fill power steering pump reservoir with specified fluid.
  1. Start engine and check for coolant and power steering fluid leaks. Service as necessary.


    Water Pump
581f50d.gif

Apr 13, 2009 | 1996 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

1,729 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...