Question about 1996 Jeep Grand Cherokee

1 Answer

No elec to coil

97 4.0l 6cyl jeep cherokee
changed out plugs, wires, entire distrubitor including insides, coil pack
still no fire

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Check your Crankshaft position sensor. or replace it

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

2004 Grand Cherokee (4.0)intermittent #1 cyl misfire and #1 injector control circuit fault (3 wks). Problem began after changing spark plugs. Replaced: coil pack, 6 injectors, & Bank #1-#2 O2 sensors.


I worked on one with the same issue. Ended up being the harness burned at the rear of the engine on the exhaust. Burned wires going to coil pack and shorted when I moved the wires to the coil packs.

Feb 22, 2017 | Jeep Cars & Trucks

1 Answer

I have a 2005 Jeep Grand Cherokee Laredo it misfires when idleing I changed the plugs yesterday it didn't start doing that until I changed the plugs


Carefully check your routing and make sure that all spark plug wires are attached to the correct spark plugs otherwise your firing order will be mixed up and cause the issue you are having. Also make sure that the wires are firmly seated on the coil packs or distributor, whichever is on your vehicle.

May 28, 2015 | 2005 Jeep Grand Cherokee Laredo

1 Answer

Turns over good good fuel pressure but no fire


Hello and welcome to FixYa!

If you have no firing issue, this can be caused by a faulty coil pack. If the coil pack is burnt, there will be no current supply to the spark plugs. One good reason why you are not burning fuel.

The coil pack is located inside the engine. Remove the cap where the plug wires are connected. Once you removed the cap you can gain access to the coil pack. Remember, removing the coil pack can be messy for it is connected to the engine. Have it replaced and you'll be good.

Hope this helps and thank you for using FixYa!

May 10, 2011 | 1993 Jeep Grand Cherokee

2 Answers

How to replace spark plugs on 2000 jeep cherokee classic 6 cyl.? Also does 2000 cherokee have inline fuel filter?


TO REPLACE SPARK PLUGS YOU REMOVE COIL PACK MOUNTING BOLTS THEN REMOVE THE COIL PACK WITH BOOT OVER THE SPARK PLUG.YOU HAVE 6 INDIVIDUAL COIL PACK TO EACH CYLINDER. YOU NEED A 3/8 RATCHET WRENCH - LONG 3/8 EXTENSION -SPARK PLUG SOCKET - SPARK PLUG GAUGE.AND TORQUE WRENCH.THE 2000 MODEL JEEPS FUEL FILTER INSIDE THE TANK.1993 - 1996 MODEL JEEPS FUEL FILTER LOCATED LEFT SIDE OF THE VECHICLE NEAR THE FUEL TANK.

Jul 20, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Changing spark plug wires on 2001 Jeep Grand cherokee


yah direct ignition coil pack does away for the need a a distributer cap and rotor.much higher energy ignition system where the computer tell when to fire.if that helps.not hard to change.as long as you change them one at a time so you don't screw up the order.

Nov 27, 2009 | 2001 Jeep Grand Cherokee

3 Answers

Firing order diagram for 1998 Jeep Cherokee Sport


1998 Jeep Cherokee 4WD 4.0L MFI 6cyl

To avoid confusion, tag and remove the spark plug wires one at a time, for replacement.
If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes to reflect how your engine is wired.

3359c2a.jpg

Fig. 1: The firing order can usually be found cast onto the intake manifold

b83cce1.jpg

Fig.: 1989-98 2.5L engine Engine firing order: 1-3-4-2 Distributor rotation: Clockwise

15d7835.jpg

Fig.: 2.8L engine Engine firing order: 1-2-3-4-5-6 Distributor rotation: Clockwise

ee028ff.jpg

Fig.: 4.0L engine Engine firing order: 1-5-3-6-2-4 Distributor rotation: Clockwise

226e0b9.jpg

Fig.: 5.2L and 5.9L engines Engine firing order: 1-8-4-3-6-5-7-2 Distributor rotation: Clockwise

Also, here can review the Jeep XJ Service Manual.

I hope help you with this, Good luck (remember rated this help).

Oct 13, 2009 | Jeep Cherokee Cars & Trucks

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...