Question about 2001 Ford Expedition

1 Answer

MOTOR MOUNTS WHERE ARE THEY LOCATED & HOW DO I REPLACE THEM?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 453 Answers

Motor mounts are located on each side of the motor at the A frame. To change them out you have to do it one at a time by unbolting one side and jack the motor on that side up about 2" or 3" until you can slide it out and put the new one in. And same for the other side. If you never did it before you might want to take it in and get it done cost about $500.

Posted on Jun 17, 2009

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: engine mounts

The engine mounts are found one on each side about the center of the engine at the bottom at the frame. There is a long bolt with a nut that holds the engine side of the mount to the frame side of the mount.

Posted on Jun 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can't find motor mount locations on 1997 Chrysler lhs


That is not possible

If the car is raised up & supported in the front

And you get under it,you can see all the motor mounts
& transaxle mounts, on the side of the engine block &
bottom of the trans --on any vehicle

Nov 03, 2014 | Cars & Trucks

1 Answer

Transmission mounts broken need to know location


I suggest you replace (All) Motor & Transaxle Mounts,
at one time

If your capable of doing vehicle work yourself,then you will
see all the mounts once your under the car

You put some wood under the oil pan & raise it a little, to get
the old mounts out & will need a long pry bar as well

Apr 01, 2014 | 2003 Dodge Neon

1 Answer

Replace rear motor mount


You should replace ALL Motor & transaxle mounts at one time

Put some wood under the motor oil pan & jack things up some,
so you can get the mounts out

Apr 01, 2014 | 1998 Toyota Sienna

1 Answer

Is it expensive to have the motor mounts replaced. 1998 Chevy Cavalier 2.4 L Engine


Not really

Do them yourself

Put some wood under the oil pan & raise
up the motor & replace all the motor & transaxle
mounts at one time

Sep 01, 2013 | Cars & Trucks

1 Answer

Replace rear motor mount


Put some wood under the oil pan & raise motor
& transaxle enough to get the mount out

You need to change ALL trans & motor mounts on that vehicle

Aug 28, 2013 | Dodge Grand Caravan Cars & Trucks

1 Answer

I need to know where they are locatedhow to install ****** & motor mounts on a 1996 buick century


the transmission mount is on the top of the transmission on the drivers side next to the battery,and one motor mount is under the motor on the passenger side next to the harmonic balancer. and the is either one or two mounts on top of the radiator to the front vavle cover

Nov 05, 2012 | 1996 Buick Century

1 Answer

Do I need to take motor out of my 98 ford Taurus to replace rear motor mount??


No you don't

Replace both motor mounts &
one trans mount, all at one time

Just support the motor under the
oil pan with a 2x6 & a jack,if you
need to move the motor a little

Sep 04, 2012 | Cars & Trucks

1 Answer

I cannot find the resistor for the blower motor on my 1997 chevy 1500 2 w d 4.3 I have looked under the dash all around the inside fire wall that i can see. I located the relay but some parts store...


First locate blower motor. The resistor is in the duct that the blower motor blows through. The resistor is actually cooled off by the blower motor. Usually it is within a foot of the blower motor & is accesible the same way that the blower motor is mounted. It may help for you to see the replacement part. All you will see next to motor is the end the wire plugs into & how it screws into duct.

Sep 24, 2010 | Chevrolet C1500 Cars & Trucks

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

Not finding what you are looking for?
2001 Ford Expedition Logo

106 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...