Question about 2005 Honda CR-V

1 Answer

Trying to take off driver side door panel but seems stuck in the middle of door. took out one screw and some plastic pop off pieces. still something holding it

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the front driver side power window switch on a 2008 Buick Enclave



Armrest Door Pull

Remove Rubber Cover

Remove 10mm *****
The first step is to pry out the plastic trim plate behind the chrome colored door release handle using a small flathead screwdriver.Then remove the 10mm ***** behind the plate using a ratcheting wrench with an extension bar attached.
Next pry out the rubber cover at the bottom of the door pull located in the center of the arm rest. Use a Torx T-25 (star bit) screwdriver to remove the two screws.
Remove Torx T25 Screws

2 T-25 Torx & 1 10mm *****

Pry Up Arm Rest Panel
Use a flathead screwdriver to pry up the rear of the plastic arm rest panel. There is a plastic hook at the front of the panel, so only pry it up from the rear edge.
Lift Rear End First

Plastic Hook At Front of Panel

Power Window Connector
After you lift out the arm rest panel, you'll need to disconnect the power connector for the window and door lock switches.
Push Connector Release Tab

Power Connector Unplugged

Two More T25 Screws
Push on the release tab with a flathead screwdriver and pull out the power window / door lock connector.Use a Torx T25 screwdriver to remove the two screws located below the arm rest panel.
Remove T25 Torx Screws

Outer Edge of Panel

Push In Center of Fastener
Then move to the outer edge of the door panel and locate the two small round fasteners. Use a small screwdriver to pop in the center pins of the two fasteners.
Pull Out Plastic Rivet

Black Plastic Fastener Removed

Remove Lower Fastener
Pull out the two plastic rivet fasteners and set them aside in a safe place.
Pull Panel Away From Door

White Plastic Pop Rivets

Pull Off Sail Panel
Grab the door pull in the arm rest and tug it towards yourself to disengage the pop rivet friction fasteners that hold the panel to the door frame.Move to the top corner of the door panel and pry off the triangular "sail" panel. On some vehicles, the sail panel contains the tweeter speaker.
Lift Panel Off Door Lock

Pull Out Door Pull Cable
Lift the door panel off the door lock button and tilt the top of it out towards yourself.Use a pair of needle nose pliers to gently lift the metal ball at the end of the door opener cable out of the mechanism.
Disconnect the door cable from the back side of the door panel.
Door Pull Cable Removed

Disconnect Power Mirror
Then disconnect the power connector for the side view mirror by lifting up on the release tab. Slide the power connector off the plastic anchor on the metal door frame.
Slide Connector Off Anchor

Unlock Connector

Connector Detached
Look behind the door panel and locate the large wire connector with the pink lever lock. Swing the lever open to unlock the connector and separate it from the socket.


Door Panel Removed

Power Window Motor

10mm Bolts
Now the door panel can be completely removed by lifting it up and off the door frame.To replace the power window motor, remove the 10mm bolts.
Stock OEM Door Speaker

Remove 7mm *****
The stock "OEM" speaker is held in place by a single 7 mm *****. Remove it with a socket and ratcheting wrench.
Pry Off OEM Speaker

Speaker Removed

Disconnect Power Plug
If the speaker is stuck to the door frame, gently pry it off with a small flathead screwdriver.Disconnect the speaker's power plug by pressing the release tab with the small flathead screwdriver.
Fits 5.25", 6.5", 6.75"

Re-installing Door Panel
According to the Crutchfield website, the 2008 to 2012 Chevrolet Malibu's front door speakers can be replaced withaftermarket speakers in the following sizes: 5 1/4", 6 1/2" or 6 3/4" speakers with the use of a bracket.If you'd like to reduce road noise, make your car quieter and also improve the sound from your speakers, I'd recommend applying some Dynamat Sound Deadener on to the metal door frame.
Re-Attach To Anchor

Plug In Power Side View Mirror

Re-Insert Power Connector
To re-install the door panel, first hold the panel close to the door frame before re-connecting the large wire plug. Swing the pink lever closed to lock it in place.Slide the socket for the power side view mirror back on to its anchor and insert the power plug.
Lock Power Connector

Pink Lever Locked

Re-Insert Door Pull Cable Ball
Insert the metal ball at the end of the door opener cable back in to the door handle mechanism.Slide the black plastic cone part of the cable back into the slot in the door opener assembly.
Door Opener Cable Reinstalled

Hang Door Panel On Frame
Gently lower the door panel down on to the edge of the door frame with the door lock switch through the opening at the top.
Line Up White Plastic Fasteners

Push On Sail Panel

Push Door Panel In Place
Move to the bottom of the door panel and line up the white plastic pop rivet fasteners with the holes in the metal door frame.Push all around the door panel to re-insert the pop rivet fasteners.
Re-attach the sail panel at the top corner of the door frame.
Push Panel Flush Against Frame

Insert Side Edge Fasteners

Insert Larger Piece First
Next move to the side edge of the door panel and first re-insert the larger piece of the two fasteners. Then insert the smaller "pin" piece of the fastener into the middle of the larger piece.
Insert Small "Pin" Piece

Install Lower Edge Fastener

Tighten 2 T25 Torx Screws

Re-Attach Power Connector

Insert Front Hook First
Insert and tighten the two Torx T-25 screws located under the arm rest.Re-attach the power connector to the plastic arm rest panel.
First insert the hook at the front of the arm rest panel and then snap the rear end in place.
Pop Arm Rest Panel In Place

Tighten 2 T25 Screws

Replace Rubber Cover
Insert and tighten the two T25 Torx screws into the door pull cup. Then replace the rubber cover over the two screws.
Tighten 10mm Door Handle *****

Replace Door Handle Trim Plate

Malibu Door Panel Replaced
Replace the 10mm ***** that goes above and behind the door opener handle and tighten it. Pop in the plastic trim plate behind the door handle.

Apr 10, 2016 | Buick Cars & Trucks

1 Answer

Front Door Panel removal removed the 5 screws on the door itself 2 on bottom 2 on inside handle and 1 behind interior door opener popped the plastic fastners around the door and removed the sideview...


Did you find the one inside the door pull cup ?
Remove the push pin rivet on the upper rear edge of the trim panel and the screw at the upper front edge near the mirror.
Remove the trim panel fasteners at the pull cup and lower the rear corner of the trim panel.
Pull up on the door trim panel assembly to disengage the trim panel to door structure attaching hooks and remove the door trim panel.
Did you try watching a video on youtube ?

May 20, 2017 | 2000 Saturn SL

1 Answer

How to take apart driver side door for motor replacement


use something plastic, usually door pieces just pop off, there may be small plastic circles or squares covering the screws that are holding your door panel on. doors are a pain, be careful, go slow, and take your time or you are going to end up replacing plastic pieces. The plastic behind the panel can be cut and re taped , or unpeeled and reglued, just helps with moisture not getting into components and frying things like your motor and switches.

Mar 11, 2010 | 2000 Dodge Caravan

2 Answers

Driver side window off track


There is what is called birds beeks that hold the door panel to the door, they have a tool to pop them out at any auto parts store. You can use a screwdriver but to avoid damage to the panel its best to use the tool, there not that expensive.

Apr 15, 2009 | 2004 Chevrolet Impala

1 Answer

Accessing the speaker on driver side door panel.


You will have to remove the entire door cover. Remove any screws you can see, pop off the cover behind the door handle remove screws behind that, pop off the plastic that holds power window switches and unplug them, then you will have to pull the door panel upwards to remove.

Mar 27, 2009 | 1997 Ford Thunderbird LX

4 Answers

Power windows


The PCM (vehicle computer) controls the power windows for your vehicle. check the power window relay under the hood before repairing PCM. Also the cheapest way is to call local garage and ask if they have a TECH2 scanner to talk to the PCM. The Dealer will charge you about $95hr. to do this.

Dec 20, 2008 | 2004 Dodge Durango

1 Answer

Broken door lock on a 2003 honda civic


There are retaining screws around the handle and the door release handle. The screws may be covered with plastic circle cover. Take those out and just start pulling the plastic panel away from the door gently yet firmly. Once you get the panel loose lift up on the panel to get it off the door.. be careful or wires that may be connected to the panel when you take it off the door.

Sep 05, 2008 | 2003 Honda Civic

1 Answer

How to remove front door panel on volvo s60 t5 2002 driver side


Pop the grab handle cover off, two different styles.

1. With a slot under the grab handle, take a small screw driver off and gently push up, it should just pop out.

2. Simple cover that can be separated with a bone tool or similar so you don't chip the cover piece.

Behind that you will find two Torx 25 screws, Take those out.

Around the edge of the panel should be around 8 plastic rivet type of thing.

Again...two different styles.

1. With center pins that blend in perfectly with the rivet. Should be about 3/32nds diameter. Push the center in and the rivet deals should pop out. Be sure not to lose the center piece...easy to lose.

2. Same deal but with a larger center pin.

Take the plastic triangle piece near the upper right hand area as facing the panel.

Pull bottom away from door and up to release from top section of door.

Careful removing the cable for the door lock release, and remove the connectors from the tweeter and driver's door module.

Aug 12, 2008 | 2005 Volvo S60

3 Answers

Drivers side power window stuck


yes,

1. trust youself

2.Open the panel slowly, some screws behind the handle opener, first you start from the bottom of the panel, and check see where has the screw connect to the door metal part and figure it out to open it. As soon as you move the panel, cut the plastic on the metal and check the small plastic wheel see it is in the track, and also check the arm connect to the motor, maybe the arm loss, be sure put a pin to connect the arm and then test it.
3. any this kind job, cost you more than $350.00 -$450.00
Hope this can help.

Jun 22, 2008 | 2000 Saab 9-3 Viggen

2 Answers

Relacing the inside driver side door handle


Its very easy to do, did mine today, pull the door panel off, 3 screws 2 on each corner of the bottom of the door and one in the grab handle tray. Look at the door handle there will be a small plastic circle that pops off remove plastic piece and remove screw, lift door panle upwards and off. 3 screws for the new door handle remove old one unclip door lock and unclip door handle install new one same way you took the old one off.

Part is $26.00 at kia, takes 15 minutes to repair!

May 14, 2008 | 2003 Kia Sedona

Not finding what you are looking for?
2005 Honda CR-V Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...