Question about 1999 Chevrolet Silverado 1500

1 Answer

How do it change filter & oil in 99 chevy z71?

Think i found filter but can't get it off 7 don't know where oil pan drain is.

Posted by on

  • Richard Scordino May 11, 2010

    Some pans do not have a drain. Most filters are inside the pan.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 135 Answers

Drain plug in in deepest part of oil pan ,looks like a bolt. loosen it then remove with a pan under it to catch all old oil, easy to drain,thanks robert b.

Posted on Jun 17, 2009

  • robert bishop Jun 17, 2009

    drain plug in in deepest part of oil pan ,looks like a bolt. loosen it then remove with a pan under it to catch all old oil, easy to drain,thanks robert b.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is the drain plug located on a 1995 chevy beretta 3.1 liter?


Radiator is on the drivers side in front of the radiator(White). Oil pan is on the back side of the pan in the middle. Not one for the transmission.

Nov 29, 2015 | Cars & Trucks

1 Answer

How to change oil on 1997 chevy venture


there is a drain plug on the bottom of the oil pan you remove to drain the oil its ether a 15mm or 14mm wrench while the oil pan is draining out unscrew the filter apply a thin coating of oil on the gasket of the new filter make sure the gasket from the old filter didn't stick to the engine install the drain plug and new filter add 4 quarts of new oil and run the car recheck for leaks and oil level that one holds 4 quarts or 4 and half not sure but 4 will be safe to start the engine

Mar 31, 2012 | 1997 Chevrolet Venture

2 Answers

How do I change the transmission oil? Where do I drain the oil from? Is their a filter to change?


If you are asking about the automatic ... the drain plug is on the passenger side and can be reached without lifting the car. It seems like they put some sort of "loctite" type product on the threads as the plug was difficult to remove. You can't change all of the oil ... about 3 quarts can be replaced ... see the owner's manual for exact amount. You could do the drain & refill a couple of times if you want to do a more thorough oil replacement. You might start by not putting all of the oil back in and check the level as you don't want to overfill. One of the *long* neck funnels is useful for adding the new oil thru the dipstick opening. There is no filter that you can replace. Honda only recommends their autotrans fluid however I used the Redline synthetic ATF that meets their specifications.

Jun 03, 2011 | 2005 Honda Civic

1 Answer

2001 dodge 5.2L r/r wtr pump & flushing ports, waterleaked to engine & now removing water from oil, approx 3 gal.isn't this a closed system? this in addition to the "oil pressure...


don't understand about the water- but do know how to cure the sludge issue
- drain oil completely- replug pan- add 1 and half gallons of K1 KEROSENE-enough that it shows full on dipstick-DO NOT START! - let sit for 24 hours - drain and put OLD oil back in -run for a couple minutes- this will ensure all kerosene out- then drain oil and change filter- did this on a 99 and got a **** lot of slime out of pan

Jun 03, 2011 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

How to change oil on a 2007 chevy tahoe


YOUR OILPAN DRAINBOLT IS ON THE ENGINE OIL PAN. THE FILTER IS ON THE ENGINE ITSELF NOT THE PAN

Aug 01, 2010 | 2007 Chevrolet Tahoe

1 Answer

Change the oil on a 2000 Dodge Caravan


Jack up pass side.Put cardboard, BIG piece under engine just in case. Using a pan to drain the oil in put under oil pan drain plug. Remove drain plug with socket wrench. Let drain 5 min. Check the gasket on the drain plug, if bad replace with new gasket .99 cents to replace gasket only on plug. Put plug back in DO NOT OVER TIGHTEN the plug. Slide drain pan with drained oil to the front to remove oil filter. Using a filter wrench remove oil filter. Let drain. When installing new filter put a little new engine oil on the rubber gasket on the filter with your finger. Screw filter back on tighten with filter wrench. Fill van with oil from front valve cover opening.

Nov 21, 2009 | 2000 Dodge Caravan

1 Answer

How do I change the tranny fluid in my 1998 cadillac catera


Fluid - A/T: Service and Repair
Transmission Fluid and Oil Filter Changing
REMOVAL PROCEDURE
1. Raise and suitably support the vehicle. Refer to Vehicle Lift Points.
2. Place drain pan under pan
3. Remove oil pan bolts from front and sides only.
4. Loosen the rear oil pan bolts approximately four turns.
5. Lightly tap the oil pan with a rubber mallet or pry to drain the fluid from main case.
6. Remove the oil pan bolts from rear oil pan and gasket.
7. Remove front oil pan bolts leaving one corner bolt in loosely.
8. Lightly tap oil pan with rubber mallet or pry to drain fluid.
9. Remove the following remaining components:
^ The front oil pan bolts
^ The oil pan
^ The gasket
10. Remove the oil filter bolts and filter.
11. Clean the following components:
^ The transmission case
^ The front adapter case
^ The oil pan gasket surfaces with solvent
^ Air dry
^ All traces of gasket material must be removed
INSTALLATION PROCEDURE
1. Install the gasket.
2. Install the oil filter.
3. Install the bolts.
^ Tighten the transmission oil filter bolts to 20 Nm (15 ft. lbs.).
NOTICE: Refer to Fastener Notice in Service Precautions.
4. Install the front oil pan.
5. Install the front oil pan gasket
6. Install the front oil pan bolts
^ Tighten the front oil pan bolts to 11 Nm (96 inch lbs.).
7. Install the following components:
^ Install the pan
^ Install the gasket
^ Install the bolts
^ Tighten the oil pan bolts to 11 Nm (96 inch lbs.).
8. Refill the transmission with DEXRON III through oil pan fill plug on the side of the (main case) oil pan. Fill the transmission to lower edge of oil
pan fill. Fill plug opening using and oil suction gun.
^ Tighten the oil pan fill plug to 45 Nm (33 ft. lbs.).
9. Lower the vehicle.
10. Check the transmission fluid level. Refer to Transmission Fluid Checking Procedure.

Sep 13, 2009 | 1998 Cadillac Catera

3 Answers

Have a 1990 Z71 4wd that with loud engine knock.


I'd consider some fresh, clean oil & filter change first of all, if it hasn't been done . drive it for a while providing it isn't too bad, & see if it goes away, if not get back to us.

May 18, 2009 | 1990 Chevrolet C1500

1 Answer

I need to know how to change the oil


Changing oil is really easy and i do not know if you have done this before so i will walk you threw compleatly. step1 jack the vehicle up and support it with jackstands before you get underit.
Step 2. Get a good oil Drain pan
3. remove the plug on the bottom of the oil pan and drain the oil in to the drain Pan caution make sure engine is not hot as the oil will burn you severaly.
4. locat your oil filter and remove and alow do drain in drain pan
5 grab the new filter and put a light coat of oil on to the gasket and screw on to your engine as tight as you can by hand now grab the oil filter wrench and turn only 1/4 of a turn tighter.
6. install drain plug back into engine oil pan and tighten down with wrench.
7 fill engine with proper oil viscosity example 5w-30 and the proper amount both can be found in owners manual.
8. start engine and look for leaks if no leaks are presant take car of of jack stands and enjoy you Well done job
hope you find this usefull
please leave me a rating
Thank you
Aaron ASE Master Technician

Apr 21, 2009 | 2005 Toyota Corolla

2 Answers

How do you change the oil filter on a Hyundai Accent 1998/99?


Replace the oil filter after draining the old oil, and" BEFORE "adding new fresh oil, otherwise you'll be dump all that fresh oil, on the ground,while you "TRY to get the new filter installed.

Step 1 Remove drain plug,Drain oil into drain pan
Step 2 Remove oil filter
Step 3 Reinstall drain plug,qnce oil has drained.
Step 4 Fill new filter with oil,lube seal on filter.
Step 5 Install new filter, Add fresh oil to proper level.replace filler cap
Step 6 Run engine check for leaks.
Happy motoring!

May 23, 2008 | 1999 Hyundai Accent

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8270 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...