Question about 2000 Saturn Ls 4dr Sedan

1 Answer

Replacing front passenger window motor/regulator... Got inner door panel off, outer door skin bolts out, but don't know how to take off the outer door handle so the door skin can come off. Not very mechanically inclined (yet)

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,341 Answers

I don't think you need to remove the outer door handle.I hope this helps and google search a bit on it and you will get the answer.According to my experience,to replace the window you don't need to remove to outside door handle..Hope this helps.

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install power window cable


cable? (electric>?)
here is the page on motor;reg.
  1. Disconnect and isolate the battery negative cable.
  2. Remove the window regulator from the door.
    • Remove door trim panel.
    • Remove isolator.
    • Remove front door glass.
    • Loosen bolts attaching regulator to inner door panel.
    • Remove bolt attaching regulator to inner door panel.
      • Lift regulator upward to disengage bolts from door inner panel.
      • Disengage power window regulator harness connector, if equipped.
      • Remove regulator through access hole in door
    • Place the window regulator on a suitable work surface and remove the screws that secure the power window motor to the window regulator.
    • Remove the power window motor from the window regulator.

Jul 04, 2014 | 2000 Jeep Grand Cherokee

1 Answer

Cable system on passenger door power window, 1999 dodge Caravan, has slipped off track. Need exploded diagram to restore to original.


REMOVAL

1. Remove the watershield. (Refer to 23 - BODY/DOOR - FRONT/WATERSHIELD - REMOVAL)

2. Remove door glass retaining clips and secure the window in the up position using masking tape or equivalent(FRONT DOOR GLASS CLIPS).

3. Disconnect wire connector from power window motor, if equipped.

4. Loosen screws attaching front and rear window guide rails to inner door panel (FRONT DOOR MANUAL WINDOW REGULATOR - TYPICAL).

5. Remove screw heads on guide rails from key hole slots in inner door panel.

6. Loosen screws attaching regulator to inner door panel.

7. Remove regulator from inner door panel.

8. Extract rear guide rail through inner door panel rear access hole (FRONT DOOR POWER WINDOW - TYPICAL).

9. Extract front guide rail through front access hole.

INSTALLATION

1. Insert front guide rail through front access hole.

2. Insert rear guide rail through rear access hole.

3. Place window regulator in position on inner door panel.

4. Place screw heads on guide rails in position through key hole slots in inner door panel.

5. Tighten screws to attach front and rear guide rails to inner door panel.

6. Connect wire connector into power window motor, if equipped.

7. Install door glass.

8. Verify door glass alignment and operation.

9. Install sound shield and door trim panel


DIAGRAMS CAN BE FOUND ON JUSTANSWER,COM

Sep 02, 2012 | 1997 Dodge Grand Caravan

1 Answer

1994 Jeep Grand Cherokee front passenger window will not operate where is the motor located how do I tell If it the motor,switch or regulator causing it not to work?


first check the switches on driver's door and passenger door , most often this is the cause. switch them around to check or use jumper wires in the connectors. motor is inside the door low towards the front. motor is bolted to window regulator assembly.
1. take off door panel and plastic liner
2. remove 3 or 4 bolts retaining assembly with window up, but mark exact location as this affects alignment
3. pivot assembly to remove rollers from track on glass
4. remove assembly through largest opening on inner door frame
5. un bolt motor from regulator
6. Install in reverse order
I am willing to elaborate on any and all of these points untill you are done, just reply to this feed for more info

Oct 04, 2010 | 1994 Jeep Grand Cherokee

1 Answer

How do i change the power window motor on the drivers door?



Aztek, Rendezvous 2001-2005 Window Systems - Power Windows Removal & Installation
  1. Position the window in the full down position.
  2. Remove the trim panel.
  3. Remove the water deflector.
  4. Remove the outer belt sealing strip.
  5. Remove the window weatherstrip.
  6. Loosen the bolts to the clevice clamps.
  7. Remove the window from the outside of the door.
To install:
  1. Position the window between the inner and the outer door panels.
  2. For front window, point the lower front corner of the window down and pass through the belt opening. For rear window, point the lower rear corner of the window down and pass through the belt opening.
  3. Align the edges with the window weatherstrip channel.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Turn the window to a horizontal position and align the window with the clevice clamps.
  5. Tighten the clevice clamps bolts to 97 inch lbs. (11 Nm).
  6. Install the window weatherstrip.
    WARNING Do NOT allow the sealing lips on the outer belt sealing strip to roll over and point downwards. If this condition is present the window will not raise properly.
  7. Install the outer belt sealing strip.
  8. Install the water deflector.
  9. Install the inner trim panel.



Window Motor & Regulator

  1. Remove the door trim panel.
  2. Remove the water deflector.
  3. For rear window, remove the rear speaker.
  4. Disconnect the window from the regulator carrier plate.
  5. Position the window in the full up position and tape it to the window frame.
  6. Disconnect the electrical connector from the window regulator motor.
  7. Loosen the bolts on the window regulator motor.
  8. Loosen the bolts on the window regulator rail.
  9. Remove the window regulator, lifting up and out from the key slots on the door inner panel and through the access hole.
To install:
  1. Install the window regulator bolts half way into the window regulator motor and the rail.
  2. Position the window regulator rail through the access hole first.
  3. Position the window regulator motor through the access hole.
    NOTE Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
  4. Install the window regulator into the key slots. Attach the regulator to the motor and the rail. Secure the regulator with bolts and tighten the bolts to 97 inch lbs. (11Nm).
  5. Remove the tape and position the window to the regulator carrier plate.
  6. Connect the window to the regulator carrier plate.
  7. Connect the electrical connector to the window regulator motor.
  8. For rear window, install the rear speaker.
  9. Install the water deflector.
  10. Install the trim panel.

Hope helps (remember rated this).

Jul 16, 2010 | 2002 Buick Rendezvous

1 Answer

I need to see how to change a window motor in a 1995 Chevy Camaro.


I'm sorry, can't contact with your chat request because I having other question open; I suggest check this proceduro for GM Camaro/Firebird 1993-1998 Repair Guide...

Window Regulator and Regulator Motor
REMOVAL & INSTALLATION
(see Figures 1 and 2)
  1. Remove the door trim panel and inner panel water deflector.
  2. Raise the window to half-up position and hold in place by inserting a rubber wedge door stops at the front and rear of the window between window and inner panel.
  3. Remove the rear guide channel and inner panel cam channel.
  4. Punch out the center pins of the regulator rivets; then drill out the rivets using a 1 / 4 in. (6mm) bit.
  5. Move the regulator rearward and disconnect wire harness from the motor (if equipped). Disengage the roller on the regulator lift arm from glass sash channel.
  6. Remove the regulator through the rear access hole.
ebf548d.jpg

Fig. 1: Front door window regulator mounting

CAUTION If electric motor removal from the regulator is required, the sector gear must be locked in position. The regulator lift arm is under tension from the counterbalance spring and could cause personal injury if the sector gear is not locked in position.
  1. Drill a hole through the regulator sector gear and backplate and install a bolt and nut to lock the sector gear in position.
  2. Using a 3 / 16 in. (5mm) bit, drill out the motor attaching rivets and remove the motor from the regulator.
00f7a3c.jpg

Fig. 2: Locking the sector gear on the window regulator motor



To install:

  1. To install the motor to the regulator. Use a rivet tool, J-29022 or equivalent, and install 3 / 16 in. (5mm) rivets or 3 / 16 in. (5mm) nuts and bolts. Remove the bolt and nut used to secure the sector gear in position.
  2. Place the regulator through the rear access hole into the door inner panel. If the electric regulator is being installed, engage the wire connector to motor prior to installing the regulator to the inner panel.
  3. Locate the lift arm roller into the glass sash channel.
  4. Using rivet tool J-29022 or equivalent, rivet the regulator to the inner panel of the door using 1 / 4 in. (6mm) 1 / 2 in. (13mm) aluminum peel type rivets (part No. 9436175 or equivalent). If the rivet tool is not available, use the following nut and bolt method:
    1. Install U-clips on the regulator at the attaching locations. Be sure to install the clips with clinch nuts on the outboard side of the regulator.
    2. Locate the regulator in the door inner panel. If the electric regulator is being installed, connect the wire connector to the regulator motor.
    3. Locate the lift arm roller in the glass sash channel.
    4. Align the regulator with clinch nuts to holes in the inner panel.
    5. Attach the regulator (and motor) to the door inner panel with 1 / 4 -20 x 1 / 2 in. screws (part No. 9419723 or equivalent) into 1 / 4 in. (6mm) nuts with integral washers. Tighten the screw to 90-125 inch lbs. (10-14 Nm) torque.
  5. Install the inner panel cam channel and rear guide channel.
  6. Remove the rubber wedge door stops at the front and rear of the window between window and inner panel.
  7. Install the inner panel water deflector and the door trim panel.

Hope helps (remember rated this).

Jun 04, 2010 | 1995 Chevrolet Camaro

1 Answer

I need a left front door/window schematic on line for a 99 Dodge Durango. I need to see how to put it together.


Front Door
  1. Remove the door trim panel.
  2. Remove the water dam.
  3. Remove the inner and outer door belt weatherstrips.
  4. Lower the window to the full down position and align the glass regulator arm with the access holes in the inner door panel.
  5. Remove the front glass run channel.
  6. Remove the nuts attaching the glass channel to regulator arm.
  7. Separate the glass and lift it up and out.
  8. Disengage the power window motor wire connector from the door harness, if equipped.
  9. Loosen the bolts in slotted holes attaching regulator to door inner panel.
  10. Remove the bolts attaching window regulator to inner door panel.
  11. Remove the regulator through the access hole in the inner door panel.
  12. Installation is the reverse of removal. Tighten the nuts attaching the glass to the lift plate to 7 ft. lbs. (9 Nm).
3455a81.gif
Power window regulator mounting—Dakota, Durango

6125789.gif
Window regulator removal—Dakota, Durango

Posting more on next post for door panel removal and installation.

Oct 26, 2009 | 1999 Dodge Durango

4 Answers

2000 Saturn SL2 driver's side electric window. Motor works - but window does not go up and down, or goes part way, or goes crooked. What is the fix and steps to accomplish it "? . Also best method to...


Fore remove the door panel in a SL2, you have to take off the door handle. You have to disengage the door locking mechanism from the door handle, then unscrew the panel and take it off.

The door handle unhinges from the locks and from the window controls. If your windows are electric, just unsnap the cord attached and leave it hanging out.

You may have to work with the door handle as it won't come out of the slot very easily and you don't have a lot of room. A flat bladed screwdriver with a long metal piece should work to unsnap it.


ION, L-Series, S-Series 1999-2005 - Window Systems

Door Glass & Regulator
Power Windows
Diagnosis & Testing
Driver's Window Switch
  1. Turn the ignition OFF, disconnect the harness connector at the driver window switch.
  2. Test for infinite resistance between the signal terminals A and B and the B+ circuit terminal E with the passenger window switch in the INACTIVE position. If less than infinite resistance, replace the driver window switch.
  3. Test for less than 2 ohms of resistance between the signal terminal A and the B+ circuit terminal E with the passenger window switch in the UP position. If greater than 2 ohms, replace the driver window switch.
  4. Test for less than 2 ohms of resistance between the signal terminal B and the B+ circuit terminal E with the passenger window switch in the DOWN position. If greater than 2 ohms, replace the driver window switch.
  5. Test for infinite resistance between the signal terminals F and H and the B+ circuit terminal E with the driver window switch in the INACTIVE position. If less than infinite resistance, replace the driver window switch.
  6. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal E with the driver window switch in the UP position. If greater than 2 ohms, replace the driver window switch
  7. Test for less than 2 ohms of resistance between the signal terminal H and the B+ circuit terminal E with the driver window switch in the DOWN position. If greater than 2 ohms, replace the driver window switch.
Passenger's Window Switch
  1. Turn the ignition OFF, disconnect the harness connector at the passenger window switch. Test for infinite resistance between the signal terminals G and F and the B+ circuit terminal with the switch in the INACTIVE position. If less than infinite resistance, replace the switch.
  2. Test for less than 2 ohms of resistance between the signal terminal G and the B+ circuit terminal with the switch in the UP position. If greater than 2 ohms, replace the switch.
  3. Test for less than 2 ohms of resistance between the signal terminal F and the B+ circuit terminal with the switch in the DOWN position. If greater than 2 ohms, replace the switch.
Window Motor
  1. Install a 30-amp fused jumper wire between the control terminal A and 12 volts. Momentarily install a jumper wire between the control terminal B and ground. The motor should perform the UP or DOWN function.
  2. If the function does not perform as specified, replace the motor.
  3. Reverse the jumper wires; the motor should perform the DOWN or UP function.
  4. If the function does not perform as specified, replace the motor.
Removal & Installation
Window Motor & Regulator
  1. Raise the window to the full UP position.
  2. Remove the upper trim panel.
  3. Remove the manual window regulator handle, if equipped.
  4. Remove the power door lock switch, if equipped.
  5. Remove the pull cup assembly.
  6. Remove the door trim push-in retainers.
  7. Remove the screw from the trim panel.
  8. Pull the bottom of the door trim out to disengage the clips.
  9. Lift up on the door trim panel to disengage the inner belt molding from the door flange.
  10. Remove the door trim panel.
  11. Remove the radio speaker.
  12. Remove the front door water deflector.
  13. Disengage the door glass to the regulator sash channel clips. Separate the door glass from the sash channel.
  14. Push the window to the up position and tape in place.
  15. Loosen the power window regulator bolts.
  16. Remove the rear regulator bolt.
  17. Lift the window regulator, disengaging the loosened bolts from the door.
  18. Disconnect the regulator electrical connector.
  19. Remove the power window regulator from the door.
To install:
  1. Installation is the reverse of removal.
Window Switch
  1. Using a flat-bladed tool, pry the switch from the door trim panel enough to expose the locking tabs.
  2. Press the locking tab to remove the switch from the door trim panel.
  3. Disconnect the electrical connector.
  4. Remove the switch.
To install:
  1. Installation is the reverse of removal.

I hope helped with this; good luck.

Oct 21, 2009 | 2000 Saturn SL

1 Answer

How do I remove and install a rear passenger side window (manual) in a 1997 Saturn SL1?The window was smashed, and I need to replace it. Thank you so much for your time and help!


Saturn Coupes/Sedans/Wagons 1991-1998 Repair Guide
Door Glass and Regulator - REMOVAL & INSTALLATION
(see Figures 1, 2, 3 and 4)
  1. Remove the outer door panel assembly. Refer to the sub-procedure under Door Locks, earlier in this section.
  2. For rear doors, loosen the bottom fastener of the rear door stationary window assembly, in order to provide clearance, then apply tape to the lower half of the outboard exposed portion of the stationary window channel. The tape must be applied in order to prevent damage to the paint surface.
  3. Lower the door glass, then use SA9148B, or an equivalent tool, to remove the glass nuts. Push the glass upward and rotate slightly, then remove the glass from the vehicle.
  4. If the regulator is also to be removed, proceed as follows:
    1. Remove the inner door trim panel. Refer to the procedure earlier in this section.
    2. If applicable, unplug the wiring harness from the power regulator.
    3. Except for the rear door, remove the regulator cam bolts.
    4. Drill out the regulator rivets and remove the regulator from the vehicle.
To install:
  1. If removed, install the regulator to the door assembly:
    1. Position the regulator to the door and secure using rivets.
    2. Except for the rear door, install the cam bolts.
    3. If applicable, connect the wiring harness to the regulator.
    4. Install the inner door trim panel to the vehicle.
  2. Install the door glass into the door and over the regulator studs.
  3. Install the glass nuts using tool SA9148B, or equivalent.
  4. Check the door glass for proper operation and alignment.
  5. If necessary, adjust the glass alignment. For rear doors, fore/aft adjustments are made after loosening the B bolts, while in/out adjustments are made when the A bolts are loosened.
  6. Except for the rear doors, glass which is not running parallel to the door header may be adjusted after loosening the inner panel cam attachment bolts and adjusting the cam. If the glass is floating in the opening, lower the glass 3 / 4 downward, loosen the front guide fasteners, push the glass rearward to seat it in the rear channel, then bring the front glass guide back to the front edge of the glass. Apply a light finger pressure on the guide and tighten the fasteners.
  7. Once the glass has been properly adjusted and is operating smoothly, install the outer door panel assembly.
cc80642.jpg

Fig. 1: Remove the glass nuts using a suitable tool-front door shown

8ca6a10.jpg

Fig. 2: Exploded view of the regulator mounting-except rear door

b18d064.jpg

Fig. 3: Exploded view of the rear door regulator mounting

0b9470a.jpg

Fig. 4: Adjustments of rear door glass are made after loosening the A or B bolts


I hope help with this (remember rated this help) Good luck.


Oct 16, 2009 | 1997 Saturn SL

1 Answer

2003 explorer front passenger window regulator/motor replcement


You will first need to remove the door panel on the inside. Then you will need to remove the window glass from the track it rests in. Then you need to undo all the screws that attach the regulator inside the door. At the top of the door where the glass slides up and down remove the inner and outer window track guides. Then very carefully maneuver the regulator up and out the top of the door. Reverse the procedure to replace. It sounds easy, but you need to almost be double jointed to do this. So, have great patience while doing this task. Good luck.

Feb 26, 2009 | 2002 Ford Explorer

1 Answer

My 2003 Forester driver side window wont work.


You need power window regulator as the cable of the regulator is out its place ,

  1. Remove the gusset cover.
  2. Pull up the inner door handle cover toward you to remove the upper hook. Pull down it to remove the lower hook. Remove the inner door handle cover.
  3. Remove the power window switch assembly.
  4. Using a trim panel remover, remove the clips of the trim panel.
  5. Remove the speaker.
  6. Using a spatula, remove the door sealer.
  7. Remove the outer mirror assembly.
  8. Remove the front end of the door weatherstrip and gusset.
  9. Remove the stabilizers.
  10. Remove the rear end of the door weatherstrip (inner and outer).
  11. Operate the power windows switch so the bolts from the regular assembly are visible through the service holes. Remove the mounting nuts.
  12. Take out the door glass. CAUTIONDo not turn the regulator in closing direction after removal of the glass. Otherwise gear may be disengaged.
  13. Loosen the nuts to remove the rear sash.
  14. Disconnect the power window motor wiring harness.
  15. Loosen the four bolts and two nuts to pull out the regulator assembly.
  16. Remove the screws to remove the motor from the regulator assembly.
  17. Installation is the reverse order of removal.0759a6d.jpg23cb1e4.jpg

Good luck...

Oct 21, 2008 | 2001 Subaru Forester

Not finding what you are looking for?
Cars & Trucks Logo

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...