Question about 2005 Nissan Sentra

1 Answer

How do you loosen the rear belt?

How do you loosen the rear belt connected to the water pump in a 96 Nisan sentra 1.6?

Posted by on

  • arteducator Jun 16, 2009

    Thanks mickydkeith, The alt does not seem to swival much. I got the front belt looses bt loosening the middle nut on a adjustable puly, I just can not figure the rear PS belt, and the Haynes manual has not helped.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Book says to loosen alternator. Loosen the alt. bolts then **** the belt. the alt should slide and allow you to remove the belt.

Posted on Jun 16, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to repace timin chani


Here's a link your timing belt replacement guide.

Feb 27, 2013 | 2002 Nissan Sentra

1 Answer

How do i change a waterpump on a 2001Volkswagen cabrio?


Your Cabrio has one of several 2.0L Volkswagen engines - determine your engine type from the
8th digit of your VIN, which will be either an "A", or "C",both are 2.0L engines.

Volkswagen 2.0L engines offered in 2001:
(a) 2.0L (Aba) Engine
(b) 2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine
(c) 2.0L (Aeg/Avh/Azg/Bdf) Engine

For completeness, I've included the water pump maintenance manual entries for all (3) 2.0L VW
engines offered in 2001. Note that the instructions below include (3) illustrations, which are
reproduced faithfully from the manual, but the last (2) illustrations are identical, since the last two
engines in the list above are virtually identical.

Volkswagen 2001 engines - water pump replacement

2.0L (Aba) Engine

Before servicing the vehicle, refer to the Precautions section.

Remove or disconnect:

1. Coolant

2. Thermostat housing from under the water pump housing.


Loosen but don't remove the bolts holding the pulley to the water pump.

Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing.


To install:


Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



archaeology_93.jpg

Fig. Water pump and thermostat housing-2.0L (ABA) engine

1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Coolant

Thermostat housing from under the water pump housing.



3. Loosen but don't remove the bolts holding the pulley to the water pump.

4. Remove or disconnect:

Timing belt cover.

Alternator and/or steering pump as required to remove the water pump drive belt.

Water pump pulley. On some vehicles, the crankshaft pulley must also be removed by removing the bolts holding the pulley to the timing belt sprocket.

Water pump from its housing. Refer to figure of ABA engine's water pump above.

To install:

1. Be sure to clean the housing before installing the new gasket. Install the pump into the housing. Pump-to-housing bolts: 84 inch lbs. (10 Nm).

2. Install the water pump drive pulley. Bolts: 15 ft. lbs. (20 Nm). Install crankshaft drive pulley. Bolts: 15 ft. lbs. (20 Nm).

3. Adjust drive belt tension and install the thermostat and housing. Bolts: 84 inch lbs. (10 Nm).



2.0L (Aeg/Avh/Azg/Bdc/Bev/Bgd) Engine


1. Before servicing the vehicle, refer to the Precautions Section.

2. Remove or disconnect:

Negative battery cable.

Coolant.

Accessory drive belt and tensioner.

Upper and center timing belt covers.



3. Position the engine so that the No. 1 cylinder is at TDC.
WARNING
Cover the timing belt to protect it from being contaminated with coolant.


4. Loosen the timing belt tension and slide the belt off the water pump sprocket.

5. Remove or disconnect:

Timing belt guard (2) mounting bolt (1), if equipped.

Water pump mounting bolts (5), then the water pump (4).

O-ring (3) and clean the seating area.


To install:



archaeology_94.jpg



Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine

1. Install or connect:

O-ring, moistened with coolant.

Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

Timing belt guard, if equipped. Mounting bolt: 15 ft. lbs. (20 Nm).

Timing belt.

Upper and center timing belt covers.

Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

Accessory drive belt.

Coolant.

Negative battery cable.



2. Check and clear any DTCs, then match the ECM to the TCM.


2.0L (Aeg/Avh/Azg/Bdf) Engine


1. Before servicing the vehicle, refer to the Precautions section.

2. Remove or disconnect:
1. Negative battery cable.

2. Coolant.

3. Accessory drive belt and tensioner.

4. Upper and center timing belt covers.


3. Position the engine so that the No. 1 cylinder is at TDC.

WARNING
Cover the timing belt to protect it from being contaminated with coolant.

Loosen the timing belt tension and slide the belt off the water pump sprocket.

Remove or disconnect:

1. Timing belt guard (2) mounting bolt (1).

2. Water pump mounting bolts (5), then the water pump (4).

3. O-ring (3) and clean the seating area.


To install:



archaeology_95.jpg


Fig. Exploded view of the water pump mounting-2.0L (AEG/AVH/AZG/BDF) engine


Install or connect:

1. O-ring, moistened with coolant.

2. Water pump so that the plug in the housing faces downward. Mounting bolts: 11 ft. lbs. (15 Nm).

3. Timing belt guard. Mounting bolt: 15 ft. lbs. (20 Nm).

4. Timing belt.

5. Upper and center timing belt covers.

6. Accessory drive belt tensioner. Mounting bolt: 18 ft. lbs. (25 Nm).

7. Accessory drive belt.

8. Coolant.

9. Negative battery cable.


Check and clear any DTCs, then match the ECM to the TCM.

Sep 13, 2011 | 2001 Volkswagen Cabrio

1 Answer

Replacing the water pump on 96 chevy S10,


Water Pump Removal & Installation 2.2L Engine To Remove:
  1. Drain the cooling system.
  2. Remove fan assembly.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt gm-03-22-606.gif

    • Water pump drive pulley bolts
    • Water pump drive pulley
    • Radiator inlet hose clamp and hose from the water pump
    • Water pump mounting bolts gm-03-22-605.gif

    • Water pump
    • Water pump gasket
    gm-03-22-607.gif

To Install:
  1. Clean the mating surfaces.
  2. Install or connect the following:
    • Water pump gasket
    • Water pump Note: Apply a sealer (GM P/N 12346004) or equivalent to the bolt threads
    • Water pump mounting bolts
      1. Torque to: 18 ft lbs (25 Nm)
    • Water pump pulley and bolts
      1. Torque to: 18 ft lbs (25 Nm)
    • Radiator hose and clamp
  3. Fill with coolant.
  4. Check for leaks.
4.3L Engine To Remove:
  1. Drain the cooling system.
  2. Remove fan assembly.
  3. Loosen the water pump pulley bolts.
  4. Remove or disconnect the following:
    • Drive belt gm_truck_43_wppulley.gif

    • Water pump drive pulley bolts
    • Water pump drive pulley
    • Radiator inlet hose clamp and hose from the water pump
    • Water pump mounting bolts gm_truck_43_waterpump.gif

    • Water pump
    • Water pump gasket
gm_truck_43_waterpump_gsk.gif

To Install:
  1. Clean the mating surfaces.
  2. Install or connect the following:
    • Water pump gasket
    • Water pump Note: Apply a sealer (GM P/N 12346004) or equivalent to the bolt threads
    • Water pump mounting bolts
      1. Torque to: 30 ft lbs (41 Nm)
    • Water pump pulley and bolts
      1. Torque to: 18 ft lbs (25 Nm)
    • Radiator hose and clamp
  3. Fill with coolant.
  4. Check for leaks.
prev.gif next.gif

Feb 12, 2011 | 1997 Chevrolet S-10 Pickup

1 Answer

Water pump going out how do i replace it


  • Removal of the Fan Shroud and Drive Belts
    • 1 Drain the cooling system. Place a waste oil collection pan underneath the petcock valve on the lower corner of the radiator. Open the petcock valve to drain the system.
    • 2 Remove the bolts that connect the fan shroud to the radiator core and remove the fan shroud.
    • 3 Loosen the alternator adjustment bolt and slide the alternator toward the engine. Remove the drive belt.
    • 4 Loosen the adjustment bolt for the air conditioning compressor, and slide the compressor toward the engine. Remove the drive belt.
    • 5 Loosen the adjustment bolt on the power steering pump and slide the pump toward the engine. Remove the drive belt.
  • Removal of the Water Pump
    • 1 Disconnect the bypass hose from the water pump by loosening the hose clamp and pulling the hose off the fitting.
    • 2 Remove the bolts that connect the water pump to the engine block, and remove the water pump and engine fan as an assembly.
    • 3 Remove the four retaining nuts that connect the fan assembly to the water pump. They will be located between the fluid coupling and the water pump pulley.
  • Installation of the Water Pump
    • 1 Attach the fan assembly to the new water pump by sliding the pulley then the fluid coupling onto the water pump and reinstalling the retaining nuts.
    • 2 Clean any old gasket material off the water pump mounting surface on the engine block.
    • 3 Place the new water pump gasket on the water pump mounting surface.
    • 4 Slide the new water pump into position and reinstall the mounting bolts.
    • 5 Reconnect the bypass hose by sliding the hose over the fitting and tightening the hose clamp.
  • Reinstalling the Drive Belts and Fan Shroud
    • 1 Reinstall the the drive belts for the power steering pump, air conditioning compressor and alternator. Tighten the adjusting bolts.
    • 2 Measure the deflection of each belt to make sure the belts are properly tightened. Measure deflection by placing a straight edge along the belt against the accessory pulley and the water pump pulley. Push down on the belt and measure the distance between the belt at the midpoint and the straight edge. It should be between 1/2 and 1/4 inch. Any more and the belt needs to be tightened. Loosen the adjustment and slide the accessory away from the engine to tighten.
    • 3 Drop the fan shroud into position and reinstall the bolts that secure it to the radiator.
    • 4 Close the petcock valve on the radiator and fill the cooling system with fresh coolant.
    • 5 Run the engine and visually inspect for leaks.



  • Dec 15, 2010 | 1992 Toyota Celica

    1 Answer

    How do i change the water pump belt on my 96 32v v8 cadillac


    Hello there:

    5f07b70.jpg
    Remove the water pump belt shield
    3f40e10.jpg
    Loosen the water pump belt adjuster and . remove the belt from around the water pump

    Sep 29, 2010 | 1996 Cadillac DeVille

    2 Answers

    I need 2004 Hyundai XG350L Service/repair Manual


    3.5L Engine

    Remove or disconnect the following:
    1. Negative battery cable
    • Engine coolant
    • Water pump pulley bolts
    • Alternator bolt, loosen only
    • Water pump pulley and drive belts
    • Crankshaft pulley
    • Timing belt cover(s)
    1. Turn the crankshaft until the timing marks on the camshaft sprocket and cylinder head are aligned.
    2. Loosen the timing belt tensioner bolt and turn the tensioner counterclockwise as far as it will go. Tighten the adjusting bolt.
    3. Mark the timing belt with an arrow showing direction of rotation.
    4. Remove the timing belt.
    5. If defective, remove the timing belt tensioner.

    9767b45.gif
    Timing belt sprocket alignment mark positioning for belt removal and installation—3.5L engine

    To install:
    1. If necessary, install the timing belt tensioner.
    2. Attach the top of the tensioner spring on the engine coolant pump pin. Ensure the hook on the pin is facing down and the hook on the tensioner is facing away from the engine
    3. Rotate the timing belt tensioner to the extreme counterclockwise position. Temporarily lock the tensioner in place.
    4. Align the timing marks of the camshaft and crankshaft sprockets.
    5. Install the timing belt on the crankshaft sprocket, then onto the rear camshaft sprocket.
    6. Route the belt to the coolant pump pulley, the front camshaft sprocket and the timing belt tensioner.
    7. Apply force counterclockwise to the rear camshaft sprocket with tension on the tight side of the belt and check that timing marks are aligned.
    8. Loosen the tensioner bolt 1–2 turns and tighten the timing belt to a tension of 57–84 lbs. (260–380 N).
    9. Turn the crankshaft two turns clockwise.
    10. Readjust the sprocket timing marks and tighten the tensioner bolts.
    11. Install the timing belt covers.
    12. Install the crankshaft pulley and tighten to 108–116 ft. lbs. (150–160 Nm).
    13. Install or connect the following:
      • Timing belt cover(s)
      • Crankshaft pulley
      • A/C compressor belt
      • Water pump pulley
      • V belt
      • Negative battery cable
      • Engine with coolant

    Feb 10, 2010 | 2004 Hyundai XG350

    1 Answer

    How do i replace a water pump on a 1994 mazda protege


    1.u need to jack the car up so u can take the passenger tire off. align the crank timing mark to top dead center with the front timing belt cover. 2. u need to loosen the crank bolt with am impact wrench, or secure the flywheel and lossen the crank bolt .3. u need a 10mm short 1/4 inch socket/or wrench inch to loosen the (4) water pump nuts. 4. i now recommend u loosen the alternator, u do not need to remove it. 5. if u have air-conditioning..i suggest u leave it on. remove the belt 6. powersteering can be loosened as well, 7. once u remove the crank pulley..u can take the 10 mm blots out of the timing belt/water pump covers.u will also need to support the engine(under the oli pan is ok) and remove the upper passenger side motor mount. 8. u will now see the timing belt. u need to remove it by loosening the tension pulley (14 mmm bolt) .u should make sure the crank is tdc. but u just need to make sure that when u re-install the new timing belt(whichu better do when u do a water pump)...,make sure the exhaust and intake cam shaft pulleys are aligned.(exhaust pulley is front side of car, intake is rear.)(e-for exhaust,i -for intake....they're aligned at center of each other (center of engine)now i must take a pee,brb in a minute. remove timing belt now 9. remove (5) 12 mm bolts from water pump. clean surface. 10. re-install in complete reverse order.i do recommend u use a black rtv gasket sealer on ur water pump gasket.(screw manufacturers statements on this use). tart with taking your two belts off, remove motor mount, remove power steering pump, crank pulley,next remove timing belt covers along with tensioners. Remove valve cover. timing belt tensioner, now you have access to the water pump. remember your timing marks before you remove. When installing timing belt hold camshaffts with vise grips to align. installation opposite of removal.



    see this video http://www.youtube.com/watch?v=c_QfsWd379A

    Jan 31, 2010 | 1994 Mazda Protege

    1 Answer

    Cange water pump on 94 nissan sentra


    Use tools quater inch socket set, remove all belts, use size 10 socket. loosen all bolts and one nut, remove at bottom, put new gasket and refitt new pump. replace all belts and refill water with antifreeze 40% and water 60%. Marco 0736775896

    Nov 06, 2009 | 1994 Nissan Sentra 4-Door

    2 Answers

    2005 Nissan Sentra 1.8S, with AC - how to replace belts?


    first of all you don't have to loosen the pulley,this will no solve the problem,well you already loosen the adjuster,good,bot thing you have not done i will tell you now,on the power steering pump where the belt pass there is also a bolt that hold it ,you must loosen that also,then after you will see the pump moving on the two position that means you will see the belt loosen on 1 position an d the position it will tight the belt,try that man.............

    Aug 23, 2009 | 2005 Nissan Sentra

    1 Answer

    Put new water pump on, cannot get belt back on


    Unbolt the pulley from the water pump, slip the belt over everything and refasten the the pulley to the pump while the belt is draped over it. Then tighten up the belt.

    Mar 13, 2009 | 1999 Nissan Sentra

    Not finding what you are looking for?
    2005 Nissan Sentra Logo

    Related Topics:

    172 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Nissan Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Phil Lovisek
    Phil Lovisek

    Level 3 Expert

    726 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Are you a Nissan Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...