Question about 2001 Hyundai XG300

1 Answer

How to change the alternator

What all has to be removed to get to the alternator for removal?

And how do you loosen the tension on the serpentine belt?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 776 Answers

Go to http://www.hmaservice.com/ and register (vehicle by VIN). Afterward, you'll have access to technical information (manuals, wiring diagrams, service bulletins, etc) about your vehicle.

Posted on Jun 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace altenator on 97 olds achieva


  1. Disconnect the negative battery cable.
  2. Label and disengage the electrical connections from the alternator.
  3. On the 2.5L engines, loosen the adjusting bolts and remove the alternator belt.
  4. If equipped with a serpentine belt, loosen the tensioner and turn it counterclockwise to remove the belt.
  5. Unfasten the alternator mounting bolts, then detach the alternator air inlet connector (3.1L engine only) and remove the alternator from the engine.
To install:
  1. Fasten the alternator to the mounting bracket, using the retaining bolts, washers and nuts. Tighten the retainers to the specifications listed in the accompanying figures.
  1. If equipped with the 3.1L engine, attach the alternator air inlet connector.
  2. Install the serpentine or alternator belt, as applicable. For details, please refer to Section 1 of this manual.
  3. Engage the alternator electrical connections. Tighten the "Bat" terminal nut to 65 inch lbs. (7 Nm).
  4. Check the belt tension, then adjust if necessary.
  5. Connect the negative battery cable, then check the alternator for proper operation.

Jul 22, 2013 | Cars & Trucks

2 Answers

I am trying to hange the serpentine belt on my 09 lancer rallyart and it keeps slipping off


Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2 Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.
  • 3 Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.
  • 4 Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.
  • 5 Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.
  • 6 Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.
  • 7 Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.
  • Oct 25, 2011 | 2008 Mitsubishi Lancer GTS CVT Sedan

    1 Answer

    How do I Change the alternator belt on my mazda?


    IF IT IS ON THE OUTSIDE OF THE OTHER BELTS, ALL YOU HAVE TO DO IS UNBOLT THE TOP OF THE ALTERNATOR, AND PUSH IT IN TO LOOSEN THE BELT FOR REMOVAL! IF IT IS IN BACK OF THE BELTS (ESPECIALLY A SERPENTINE BELT) YOU'LL HAVE TO REMOVE THE SERPENTINE BELT FIRST! THERE WILL BE A TENSION PULLEY HOLDING THE BELT TIGHT! YOU'LL NEED TO USE A WRENCH TO PULL THE TENSION PULLEY TOWARD YOU TO LOOSEN BELT! WATCH HOW YOU REMOVE IT, BCUS YOU'LL NEED TO PUT IT BACK ON THE SAME WAY! THEN REMOVE, AND REPLACE THE ALTERNATOR BELT AS BEFORE, THEN REPLACE THE SERPENTINE BELT!

    Mar 05, 2011 | Mazda Protege Cars & Trucks

    1 Answer

    I need to know how to change a serpentine belt on a 1997 plymouth breeze 2.0. Maybe have a schematic or something?


    Hello there,

    For your vehicle, the alternator serves as the tensioner in at least the 2.0 engine. Loosen the lower alternator mounting bolt. Then take off the nut on the top left of the alternator. Finally loosen the bolt on the top of the alternator, (it faces you). You can then remove the bolt that runs through the alternator. This will allow you to remove the old belt and replace it.

    Best regards...

    Jan 22, 2011 | 1997 Plymouth Breeze

    1 Answer

    How to replace alternator


    Remove the negative battery cable from the battery.
    2. Loosen the right front wheel lug nuts.
    3. Jack up the automobile and place jack stands in appropriate positions. Leave room to access the alternator from underneath the car.
    4. Complete removal of the right front wheel.
    5. Remove the right front lower splash shield.
    6. Release tension on the serpentine belt at the tensioner.
    7. Slip the belt off of the tensioner and the alternator.
    8. Attach an engine hoist at the front of the engine. This is a transverse mounted engine and the hoist will need to be attached near the engine mount located at the right front fender inner fender.
    9. Remove the top portion of this mount.
    10. Loosen the rear engine mount at the firewall. This mount is slotted and will permit you to pull the engine forward toward the right front corner of the engine compartment. This will give access to the alternator.
    11. Remove the two bolts that attach the serpentine belt tensioner and remove the tensioner.
    12. Remove the top alternator mounting bolt. Do this from the engine compartment side.
    13. Remove the lower alternator mounting bolt. Do this from underneath the car.
    14. Turn the rear of the alternator up to access and remove the electrical leads.
    15. Remove the alternator from the engine compartment.
    16. Install the new alternator in the REVERSE ORDER.


    hope this helps if it does please give a thumbs up rateing thank you have nice day

    Dec 28, 2010 | 2002 Saab 9-5

    2 Answers

    Changing alternator on 99 dodge ram truck 5.9L engine...anything I need to do before loosening the alternator bolts?


    always take the negative battery terminal off to avoid shorting the charge wire. Next, remove the serpentine belt by twisting the tensioner loose. Then you can remove the alternator bolts. Let me know if you have more questions.

    Oct 22, 2010 | Dodge Ram 1500 Cars & Trucks

    1 Answer

    Replace alternator belt


  • Locate the two belts on the left side (passenger side) of your Mitsubishi Lancer. The outer belt is a serpentine belt, operating four pulleys and the inner belt is your alternator belt.

  • 2

    Follow the serpentine (outer) belt to the three pulleys lined up vertically near the front of the engine compartment. Locate the middle pulley, which is the tension pulley for the belt.

  • 3

    Loosen the bolt on the middle pulley with a socket wrench by turning counter-clockwise. Do not remove the bolt, just turn it a couple of times. Loosen the tensioner bolt on the side of the of the pulley, facing the front of the vehicle.

  • 4

    Remove the serpentine belt and then loosen the bolt on the alternator. With the alternator loose, move it forward so that the alternator belt loosens up and then remove belt from the pulleys.

  • 5

    Install the new alternator belt by placing it over both inside pulleys. Tighten the tension on the alternator belt by moving the alternator back and keeping tension on it by holding it back with a long screwdriver. While the alternator belt is tight, use a socket wrench to tighten up the bolt on the alternator.

  • 6

    Place the serpentine belt back on the pulleys and then use a socket wrench on the bolt on the front of the tension pulley. Once the serpentine belt is tight, tighten up the bolt in the middle of the tension pulley.

  • 7

    Start the Mitsubishi Lancer's engine to test the alternator belt and make sure it is working properly. Once you have verified it is working, turn the engine off.

  • Oct 08, 2010 | 2002 Mitsubishi Lancer

    1 Answer

    How do change a water pump on 1998 ford escort


    You have too remove the alternator, tensioner pulley, and probably would help to disconnect the power steering hose too give you a little more room too work. Now getting the pulley off the water pump is always the pain, see if you can loosen those bolts before removing the tension on the serpentine belt. If not try using a rubber oil filter remover to hold while you loosen the bolts.

    Jan 16, 2010 | 1998 Ford Escort

    1 Answer

    Removal of serpentine belt on a 1996 Buick automobile?


    check if it has a tensioner, it look like a useless pully and put a breaker bar on it and pull it and the belt should loosen up, if theres no tensioner the alternator should have bolts to loosen up the belts.

    Jun 27, 2009 | 1996 Buick Skylark

    2 Answers

    How do I release the tension in the serpentine belt?


    there is an 8mm bolt right under the alternator. loosen that up then loosen the bolt on the idler pulley and itll come right off

    Jun 14, 2009 | 1996 Nissan Sentra

    Not finding what you are looking for?
    2001 Hyundai XG300 Logo

    126 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Hyundai Experts

    yadayada
    yadayada

    Level 3 Expert

    76132 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Hyundai Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...