Question about 1989 Ford F 150

1 Answer


Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

You have to remove steering wheel and lock plate. Under the lock plate is a screw that holds cyl in column.

Posted on Jun 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Removing Ignition cylinder

Us a small metal curved pick and a small screw driver and with a little Patience you can get the broke key out . Good luck

May 19, 2013 | Cars & Trucks

1 Answer

Broke key in ignition 1990 chevy silverado

See if you can get a pick or a small screwdriver and pull or pry the broken piece out. take that end of the key to the dealer or locksmith to cut a new key. if your handy with tools its not that hard just try not to break anything else while your doing it.

Jul 17, 2012 | Chevrolet C1500 Cars & Trucks

1 Answer

I broke my key in the ignition switch. How do I remove it

You can try a high powered magnet, i would try a pick set, get two needle point picks and pinch the key between them and pull out. You can pick up a pick set at your local parts store.

Aug 24, 2011 | 1993 Mazda Protege

1 Answer

Can't seem to see where the oil pressure switch is on my 1988 chevy pick - up 1/2 ton 5.7 liter. Need a diagram or picture to see where it is exactly

Hello: The oil pressure sensor is at the rear top of the engine near/under the ignition distributor, has one electrical connector. You may have to remove the ignition distributor to get to it unless you have a special oil pressure socket.

Jan 06, 2011 | 1988 Chevrolet C1500

1 Answer


Remove the horn ,then the nut holding the steering wheel on,then using a steering wheel puller,remove the steering wheel,then remove the lock plate,using a lock plate remover,then remove the turn signal switch,and there is a screw pin,that holds the ignition key cylinder in,remove it,and pull the key cylinder out.

Jan 29, 2010 | 1988 GMC Safari

1 Answer

2002 grand prix...key broke in ignition.

You may get it out using a pick, or a paperclip with a very small bend on the end. If you can't get it to come out from there, you may need to replace the ignition tumbler. Let me know, and I'll give you the steps if necessary.

May 23, 2009 | 1988 Pontiac Grand Prix

1 Answer

I turned my ignition switch and it turned in a circle without turning over. i think the switch broke. how can i hot wire it to get it home?

The ignition switch actuator broke. Turn the key on, on top of the column is the ignition switch. It has a rod going to it. Use some needle nose pliers and push the rod to the front of the truck. Good luck

May 05, 2009 | 1988 Ford F 150

Not finding what you are looking for?
Cars & Trucks Logo

191 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides