Question about 2003 Ford Explorer Sport Trac

Open Question

I am getting no spark, ford explorer sport trac 2003, changed ciol plat, Cranks but won;t start, I see no spark at plugs, change coil plate and still no spark. Seems like a ECM issue?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
chuck943
  • 783 Answers

SOURCE: 2007 FORD EXPLORER SPORT TRAC 4X4 Change oil light on

Press and hold the SELECT/RESET
control switch to select SYSTEM
CHECK when “SYSTEM CHECK /
HOLD RESET” is displayed in the
message center. Selecting this
function from the SETUP MENU
causes the message center to cycle through each of the systems being
monitored. For each of the monitored systems, the message center will
indicate either an OK message or a warning message for two seconds.
Pressing the SELECT/RESET control switch cycles the message center
through each of the systems being monitored.

The sequence of the system check report and how it appears in the
message center is as follows:
1. OIL LIFE RESET
2. CHARGING SYSTEM
3. WASHER FLUID
4. DOOR AJAR
5. EXTERIOR LAMP
6. BRAKE SYSTEM
7. PARK BRAKE
8. MILES TO EMPTY
9. FUEL LEVEL LOW (will only display if 50 miles or less to empty)
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Enter SYSTEM CHECK to display
“OIL XXX% RESET IF NEW”.
2. Press SELECT/RESET control
switch to display “HOLD RESET IF
NEW OIL”.
3. Press and hold the
SELECT/RESET control switch for
more than 2 seconds. Oil life is set
to 100% and “OIL CHANGE SET TO
100%” is displayed.

Posted on Apr 02, 2009

Ad
  • 12 Answers

SOURCE: how to change fuel filter on 2001 ford explorer

it in the tank so your gonna either gonna have to drain the tank and lower it to the ground,it shouldn't take more than 30 minutes.make sure you put the seal back in right,so it won't leak,it aint very hard.

Posted on Jul 12, 2009

  • 5546 Answers

SOURCE: 2004 FORD EXPLORER SPORT TRAC POWER WINDOWS AND

Look in the owners manual and see if they have a circuit breaker or relay instead of a fuse. It could be bad and you would not see it.

Posted on Jul 23, 2009

morse008
  • 1111 Answers

SOURCE: Change spark plug wires on a 2004 Sport Trac

through the wheel wells

Posted on Aug 22, 2009

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the tools.....how else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford sport trac getting gas odor on passenger's side after driving several miles


have seen loose spark plugs do this. fuel leaks usually don't make it to ground hot engine evaporates it.

Sep 06, 2014 | 2003 Ford Explorer Sport Trac

1 Answer

03 ford explorer has orange spark from plug wires


check both the disributor cap. and your rotor arm.

Dec 18, 2013 | 2003 Ford Explorer Sport XLT

1 Answer

I have a Ford Explorer Sport Trac Limited Edition, V8. My Truck Seems to be miss firing more in the cold weather we have been having where I live. However, even in warm weather it miss fires just not as...


easy way to check coil pack and hi tension cable, use a spark plug cut some of the threaded part to leave a 10 mm gap to the center electrode weld on a clamp , clip the clamp to earth attach the Ht cable to the plug, the spark must jump this 10 mm gap. Note don't run the engine longer then one minute as the mixture will be rich and heat up the converter

Apr 19, 2017 | 2007 Ford Explorer Sport Trac

1 Answer

Truck won't turn over or start


if it wont turn over that means there is no spark to your spark plugs u mite check your distributor cap or it could more seriouse like the ECU in the vehicle which is the brain and I justthot of this how about changing the ignition in the steering column before anything else>

Apr 07, 2013 | 2003 Ford Explorer Sport Trac

1 Answer

Won't start after sitting yesterday and lastnight in cold


remove a spark plug and reconnect its cable, sit it on engine and crank. do you see a spark on the plug?

Dec 20, 2012 | 2004 Ford Explorer Sport Trac

1 Answer

How do I change spark plugs that I can't reach


Raise and support the vehicle. Remove the passenger side tire. Access the plugs through the wheel house opening.

Feb 27, 2012 | 2001 Ford Explorer Sport Trac

1 Answer

2001 ford explore sport cranks but will not start.


TUNEUP? WHAT WAS CHANGED?NEED TO CHANGE WIRES,PLUGS CAP&ROTOR ELECTRIC COIL, CHANGE THE FUEL FILTER,IF STILL THE SAME?TAKE OUT THE FUEL FILTER IF WET THEN OK, BUT IF DRY THEN ,FUEL NOT GETTING TO THE ENGINE,CK WIRES TO AND FROM THE PUMP,STILL THE SAME THEN NEW PUMP

Oct 30, 2009 | 2001 Ford Explorer Sport

Not finding what you are looking for?
2003 Ford Explorer Sport Trac Logo

Related Topics:

432 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...