Question about 1996 Honda Accord

1 Answer

1996 accord control panel

How do i remove control panel

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 39 Answers

Remove the center consule up to the radio. Remove the glove compartment. This will free up the radio consule. From there, you can remove the AC control panel

Posted on Aug 21, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1996 Honda accord cabin air control won't switch to full cold it's only warm air is it sticking in the air box or off track idk the knob won't turn all the way to cold either I force it and it clicks back...


the air control heat knob needs removing to determine if its the knob itself, this will just pull off, look at reverse of knod and look to see if the center locating pigot is worn "round" or broken , if this looks ok then the panel housing the knob controls will need removing and then check if the heat control wire is in place, if so trace this wire ,this is a bare steel control wire not an electrical wire, to the heater box lower dash behind the control panel and see if you can manually move the heat control flap this will look like two toothed semi circular cogs that inter lock , one may have jumped out of place try a little vaseline on the cogs to help lubricate the movement,this is just good practice, after all this i think you will have found the problem

May 04, 2014 | 1996 Honda Accord

1 Answer

1996 Honda Accord Wagon imported from Japan climate controll not working. Any ideas


problem could be in the heater control panel .if you dont find any bad fuses or any electrical faults.let garage check it out climate control systems dealing with electronics best let a garage check it out.

Dec 20, 2012 | 1996 Honda Accord

1 Answer

What can cause a no power condition to ac compresor on 1996 Lincoln town car?


Instructions1 See if the problem is as simple as a blown fuse. It is probably a blown fuse if the temperature controls on the dashboard seem to work correctly but have no effect on the air. The fuse box in a Lincoln Navigator is located by the brake on the left lower side of the steering wheel. Pry off the fuse panel cover and find the blown fuse.
2 Have a look at the control panel next, if the controls are not working at all. First disconnect the negative battery cable. Detach the shift lever cover, and then the electrical connector. Unscrew the screws holding the trim cover on the shift panel. Disengage the four clips to pull the trim panel off.
3 Unplug the electrical connectors, remove four more screws, open the audio unit cover the whole way, disengage the clips in each corner and remove the climate control panel.
4 Listen for the blower motor to be properly working while the engine is running with the air conditioning controls turned to high. Adjust them from low to high to make sure the blower motor noise increases and decrease accordingly.
5 Find the blower motor in a Lincoln Navigator underneath the passenger side lower trim panel. Push the carpet back. Unplug the electrical connection from the blower motor, remove four screws and pull the motor out.
Thanks

Apr 02, 2012 | 1996 Lincoln Town Car

1 Answer

1996 honda accord drivers window doesn't roll up and down well.


need to remove door panel remove window regulator grease regulator and re-install

Feb 07, 2010 | 1996 Honda Accord

1 Answer

1996 honda Accord drivers window stuck down


If you here a click when you push the switch up or down, then it could be your window regulator (motor). To change remove door panel, there should be 3 bolts holding regulator to door frame and 2 bolts connecting regulator arm to window.

Nov 17, 2009 | 1996 Honda Accord

2 Answers

The automatic door lock on my 96 Honda Accord makes a loud buzzing sound when locking. Is there anyway to fix it myself? How do I take off the door panel to


My 1996 Honda had the same thing on the driver side door.

It was caused by a deteriorated rubber stop inside the door lock actuator module. The module is buried down in the lower outside corner of the door. Inside the module there is a track on which two electrical contacts slide along with the actuator, and a small rubber bumper stop. When this stop deteriorates, the contacts over travel and run off the track. Evidently this confuses the actuator controller into oscillation. The control module limits the time this occurs, so the buzz stops after a short while. There is somewhat of a spring return action to the mechanism, so the contacts return to the track, making things good again.

The dealer couldn't get just the rubber part, so $130+ for the whole module. My make-shift o-ring replacement only lasted a few months.

Definitely a chore to get the module out and back in.

HTH

Jul 11, 2009 | 1996 Honda Accord

1 Answer

Replacing hazard swith for Honda Accord 1996


u must remove the center console....remove the ashtray..(pull it ) remove the plastic trim piece around the shifter , should just pop off ,,,held on by clips...u will see 2 phillips screws under that piece., the 2 screws that secure the trim panel that ur hazard switch is attached to.....remove those screws and gently pull the panel off , u may have to unplug the clock and otherm necessary connectors includeing the hazard switch connector to remove the panel..u should be able to remove the switch with a screwdriver..reinstall everything back the way u took it off...be sure to plug the cig lighter back in...

Apr 08, 2009 | 1996 Honda Accord

2 Answers

How to replace heater core 93 honda del sol


Heater Core Honda Civic/CRX/del Sol 1984-1995 Repair Guide REMOVAL&INSTALLATION
See Figures 1, 2 and 3
REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable and disable the SRS system (if equipped.)
WARNING All SRS wire harnesses are covered with a yellow insulation. Read the SRS precautions found in this section and install the short connectors as described.
  1. Properly drain the cooling system.
  2. Disconnect and plug the heater hoses at the firewall.
  3. Disconnect the heater valve control cable.
  4. Remove the heater unit attaching nut on the firewall.
  5. Remove the dashboard as follows:
    1. Remove the center panel.
    2. Disconnect the wire connectors at the fuse box.
    3. Disconnect the sunroof switch connector, if equipped.
    4. Disconnect the ground cable at the right of the steering column and the power mirror switch wire connector.
    5. Remove the side air vent knob and face plate.
    6. Remove the screws attaching the air vent control lever.
    7. Remove the center panel, radio and heater control head.
    8. Remove the gauge upper panel (4-door) or instrument panel (3-door).
    9. Disconnect the speedometer cable.
    10. Remove the center upper lid.
    11. Remove the side defroster garnishes on both ends of the dash.
    12. Lower the steering column.
    13. Remove the dashboard mounting bolts.
    14. Lift and remove the dashboard assembly.
  6. Remove the heater duct.
0900c15280061a21.jpgFig. 1: Removing the heater duct assembly
  1. Remove the steering column bracket and duct assembly.
  2. Remove the heater assembly mounting bolts.
  3. Remove the heater assembly and remove the heater core.
0900c15280061a22.jpgFig. 2: Removing the heater case assembly 0900c15280061a23.jpgFig. 3: Removing the heater core from the heater caseTo install:
  1. Install the heater core into the heater unit.
  2. Install the heater assembly and the attaching bolts.
  3. Install the heater duct and steering column bracket.
  4. Install the dashboard assembly. Tighten the mounting bolts until just snug.
  5. Raise and attach the steering column.
  6. Install the center upper panel.
  7. Connect the speedometer cable and install the instrument gauge assembly.
  8. Install the control head, radio and center panel.
  9. Install the side vent and face plate.
  10. Connect the ground cable at the right of the steering column and the power mirror switch wire connector.
  11. Connect the sunroof switch connector, if equipped.
  12. Connect wire connectors at fuse panel.
  13. Install the heater unit attaching nut on the firewall.
  14. Connect the heater valve control cable.
  15. Connect the heater hoses at the firewall.
  16. Connect the negative battery cable.
  17. Fill, bleed and leak check the cooling system.

Sep 01, 2008 | 1996 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...